Industrial 1-port 802.3at PoE+ to 2-port 802.
Trademarks Copyright © PLANET Technology Corp. 2017. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Contents 1. Introduction............................................................................... 5 1.1 Package Contents................................................................ 5 1.2 How to Use This Manual....................................................... 5 1.3 Product Features.................................................................. 5 1.4 Product Specifications.......................................................... 8 1.5 Power over Ethernet Budget....................
1. Introduction 1.1 Package Contents Check your package for the following parts: Industrial PoE Extender x 1 User’s Manual x 1 Waterproof RJ45 Connector x 3 Wall-mounted Kit x 1 If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 1.
Power over Ethernet 1-port data + power input Complies with IEEE 802.3at Power over Ethernet Plus endspan/mid-span PD Supports PoE input power up to 30.8 watts 2-port data + power output Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet/ end-span PSE Up to 2 IEEE 802.3af/802.3at devices powered Supports PoE power up to 25 watts for each PoE port Auto detects powered device (PD) Extends the range of PoE to an additional 100 meters (328ft.
Industrial Case and Installation IP63 aluminum case Wall-mount design Waterproof and dustproof Supports EFT protection of 2000 VDC for power line Supports 2000 VDC Ethernet ESD protection -40 to 75 degrees C operating temperature No external power cable required for installation Plug and Play installation Standard Compliance IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab 1000BASE-T IEEE 802.3x Flow Control IEEE 802.3at Power over Ethernet Plus IEEE 802.
1.4 Product Specifications Model IPOE-E202 Hardware Specifications Hardware Version 2 Network Connector PoE In Port 1 x 10/100/1000BASE-T Ethernet with High PoE “Data + Power” in, auto MDI/MDI-X, auto-negotiation RJ45 connector PoE Out Port 2 x 10/100/1000BASE-T Ethernet with IEEE 802.
Dimensions (W x D x H) 199.6 x 81 x 40 mm Weight 373g Power Consumption 30 watts/102.3BTU (Full loading with PoE function) Power over Ethernet PoE Standard PoE In Port IEEE 802.3at Power over Ethernet Plus end-span/mid-span PD class 4 PD Per PoE Out Port IEEE 802.3at Power over Ethernet Plus end-span PSE IEEE 802.3af Power over Ethernet end-span PSE PoE Power PoE In Port 50~57V DC, max. 30.8 watts Per PoE Out Port 44~55V DC, max.
1.5 Power over Ethernet Budget The following table lists how many PoE devices can be powered by IPOE-E202: PoE Output Budget* Power Source IEEE 802.3at PoE+ PSE 25 watts max. Max. Number of PDs supported Class 4 PD@25 watts 1 unit Class 3 PD@15 watts 2 units Class 2 PD@7 watts 2 units IEEE 802.3af PoE PSE Remarks 10 watts max. Class 2 PD@7 watts 1 unit The PoE output budget means the 2-port PD aggregated power output. The aggregated power consumption will be below 30 watts if with PoE+ PSE. 1.
20M 2M 25.8 20M 20M 24.8 20M 20M 60M 100M 18 13.2 60M 60M 2M 20M 18 16.7 60M 60M 60M 100M 13 10.3 100M 100M 2M 20M 13.2 12.4 100M 60M 9.8 100M 100M 8.9 1.6.2 When PSE/PoE Switch Output is DC 56V A (Distance) B (Distance) 2M 2M 26 2M 20M 25.8 2M 2M 60M 100M 24.7 23.5 20M 20M 2M 20M 25.7 25.4 20M 20M 60M 100M 24.4 22.2 60M 60M 2M 20M 24.5 24.2 60M 60M 60M 100M 21.7 17.5 100M 100M 2M 20M 22.2 20.9 100M 60M 17.2 100M 100M 15.
2. Installation This section describes the functionalities of the industrial PoE extender’s components and guides you to how to install it. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Physical Dimensions IPOE-E202 industrial 1-port 802.3at PoE+ to 2-port 802.3af PoE extender dimensions: (W x D x H): 199.
2.2 Front Panel Figure 2-1 shows the front panel of industrial Power over Ethernet extender PoE IN Budget Alert 1000 LNK/ACT 10/100/1000T PWR IPOE-E202 Figure 2-1: IPOE-E202 Front Panel System LED PWR Color Green Function Lights to indicate the IPOE-E202 has power. PoE Input Port LED Color Function LNK/ACT Orange Blinks to indicate that the IPOE-E202 is actively sending or receiving data over that port.
2.3 Rear Panel Figure 2-2 shows the rear panel of the industrial Power over Ethernet extender PoE 1 Out PoE 2 Out LNK ACT PoE In-use Figure 2-2: IPOE-E202 Rear Panel PoE Output Port (Port 1 ~ 2) LED Color Function Lights to indicate the port is linked up at 10/100/1000Mbps. LNK/ACT PoE-in-Use Green Orange Blinks to indicate that the IPOE-E202 is actively sending or receiving data over that port. Lights to indicate the port is providing PoE power.
2.4.1 Making Waterproof RJ45 Cable Step 1: Take a waterproof RJ45 jack out from the IPOE-E202 box and prepare one RJ45 cable. Step 2: Insert the RJ45 cable through the waterproof RJ45 jack. Step 3: Prepare an RJ45 connector. Step 4: Put the RJ45 connector in place with cable crimper.
Step 5: To lock in the RJ45 connector, pull back the cable till the connector nicely fit into the waterproof connector hole. 1. Use only the waterproof RJ45 connector provided in the package of IPOE-E202. 2. If the waterproof RJ45 connector is found missing or damage, please contact your local reseller where you purchased from. If the new waterproof RJ45 connector is obtained from PLANET, make sure its dimensions are the same. Note 3.
Step 1: Take the four screws from the box. Step 2: Place the IPOE-E202 on the wall. Step 3: Use a screwdriver to screw it into the wall. 2.4.3 Connecting waterproof RJ45 connector to the IPOE-E202 Step 1: Insert the waterproof RJ45 connector into the port of the IPOE-E202.
Step 2: Turn clockwise to tighten the screw nut.
2.5 Connecting IPOE-E202 to Power Source Equipment (PSE) This section describes how to install industrial Power over Ethernet extender and make connection to it. Please read the following topics and perform the procedures in the order being presented. There are 3 RJ45 ports in the industrial Power over Ethernet extender, of which the “PoE IN” port functions as “PoE (Data and Power) input” and the “PoE-in-Use” port on the other side functions as “PoE (Data and Power) output”.
2.6 Connecting IPOE-E202 to Powered Device (PD) Step 1: Connect the additional Cat5e/6 cable that will be used to connect to the remote Powered Device (PD) to the “PoE-in-Use” port of the IPOE-E202. PoE Wireless AP IPOE-E202 PoE Camera Step 2: The “PoE-in-Use” port is also the power injector which transmits DC voltage to the Cat5e/6 cable and transfer data and power simultaneously between the PSE and PD.
Step 3: Once the IPOE-E202 detects the existence of an IEEE 802.3at/af device, the “PoE-in-Use” LED indicator will be lit steadily, showing it is providing power. 1 In 1 Out 25W Power PoE+/30W 100m Data IEEE 802.3at/25W 100m PoE Injector/Switch PoE PTZ IP Camera PoE Extender 12W+12W 1 In 2 Out Power IEEE 802.3af/12W 100m PoE+/30W 100m Data IEEE 802.3af/12W 100m PoE Injector/Switch PoE Extender Note PoE Dome IP Camera 1. If the connected device is not fully complying with IEEE 802.
3. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource and user’s manual on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address: support_switch@planet.com.tw Copyright © PLANET Technology Corp. 2017. Contents are subject to revision without prior notice.
APPENDIX A: Networking Connection A.
A.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
