User's Manual

- 10 - - 12 - - 13 - - 14 -
- 9 - - 11 -
Step 2: Refer to the picture below to screw the four screws on the wall.
140.00mm
129.00mm
60.00mmØ4.50mm
Ø7.00mm
Step 3: Use a screwdriver to screw them into the wall.
3.4 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
Earth Ground
4.ProductSpecications
Product IPOE-175
Hardware Specications
Interface
Input Port
1 x 10/100/1000BASE-T “Data” in RJ45
port
Output Port
1 x 10/100/1000BASE-T Ethernet with
IEEE 802.3bt PoE++
“Data + DC” out RJ45 port
Input Power
Terminal Block
1 x 2-pin terminal block
- Pin 1/2 for Power (Pin 1: V+ / Pin 2: V-)
Data Rate 10/100/1000Mbps
LED Indicator
PWR (Green)
PoE-in-Use x 1 (Amber)
Input Voltage 24~56V DC
Power Consumption
Voltage System on Full Load (Max.)
DC 24V 1.2W 72W
DC 36V 1.44W 70.56W
DC 54V 1.71W 65.8W
DC 56V 2.24W 62.1W
ESD Protection
Air 8KV DC
Contact 6KV DC
Surge Protection 6KV
Enclosure IP67-rated and IK10 aluminum case
Installation Wall-mount ear
Standards Conformance
Regulatory Compliance
FCC Part 15 Class A
CE
Stability Testing
IEC 60068-2-32 (Free fall)
IEC 60068-2-27 (Shock)
IEC 60068-2-6 (Vibration)
Standards Conformances
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
Environment
Operating Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
Note
The PoE power output ability will depend on the distance.
5. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource and user’s manual on PLANET web site rst to check if it
could solve your issue. If you need more support information, please
contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=2
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Note
EMD (Lightning) DAMAGE IS NOT CONVERED UNDER
WARRANTY.
3.5 Connecting IPOE-175 to PD
Step 1: Connect the additional Cat5e/6 cable from the PoE++ Out of
the IPOE-175 to a remote PD.
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
PoE
Power
Data
PoE IP Camera
IPOE-175
Data
100m
802.3bt PoE++
Power Supply
Power
DC
DC24-56V
Ethernet Switch
Step 2: The PoE++ Out port is the power injector which transmits DC
voltage to the Cat5e/6 cable and transfer data from the Data
source.
Step 3: Once the IPOE-175 detects the existence of an IEEE 802.3at/
bt device or Ethernet device, the PoE-in-Use LED indicator
will be lit steadily, showing it is providing power.
Note
According to IEEE 802.3at/bt standard, the IPOE-175
will not inject power to the cable if not connected to a
standard IEEE 802.3at/bt device.
Dimensions (W x D x H)
150 x 43.8 x 72.94 mm
169.85 x 43.8 x 72.94 mm, with cable
gland
Weight
339g
373g (with three waterproof cable glands)
MTBF >100000 hours
Network Cable
10BASE-T: UTP category 3, 5 cable
(≤100m)
100BASE-TX: UTP category 5, 5e cable
(≤100m)
1000BASE-T: UTP category 5e, 6 cable
(≤100m)
Power over Ethernet
PoE Standard
IEEE 802.3bt PoE++ type 3 PSE
Backward compatible with IEEE 802.3at
PoE+
PoE Power Supply Type
802.3bt/PoH (Power over HDBaseT)
End-span/Mid-span
PoE Power Output
55V DC
Max. 60 watts to 802.3bt PoE++ PD
Max. 60 watts to PoH PD
Max. 30 watts to 802.3at PoE+ PD
Power Pin Assignment
802.3bt/PoH: 1/2 (-), 3/6 (+), 4/5 (+),
7/8 (-)
End-span: 1/2 (-), 3/6 (+)
Mid-span: 4/5 (+), 7/8 (-)