User's Manual

- 2 - - 4 - - 6 - - 8 -
- 1 - - 3 - - 5 - - 7 -
1. Package Contents
Thank you for purchasing PLANET Industrial IP67 1-port 10/100/1000T
802.3bt PoE++ Injector, IPOE-175. In the following sections, the term
“Outdoor PoE Injector” means the IPOE-175.
Open the box of the Outdoor PoE Injector and carefully unpack it. The
box should contain the following items:
IPOE-175 x 1 User's Manual x 1 Wall-mounted Kit x 1
Spanner x 1
Power Cable with 2-pin
Terminal Block x 1
M22 Waterproof
Cable Gland x 3
Ground Wire x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
2.2 Power Input Port
Figure 2-2 shows the Power Input port side of the IPOE-175
Figure 2-2: Power Input Port
2.3 Data Input Port and 802.3bt PoE++ Output Port
Figure 2-3 shows the Data Input Port and PoE++ Output Port side of
the IPOE-175.
PoE++ Output Port Data Input Port
Figure 2-3: Two RJ45 Ports
Caution
Make sure the clamping nut is tightly attached to the
cable gland body and the sealing insert is squeezed
tightly.
Step 5: Repeat Steps 1 to 4 for “Data” Input Port and“PoE (Data +
Power)” Output Port
3. Installation
This section describes how to install the Outdoor PoE Injector and make
connections to it. Please read the following topics and perform the
procedure in the order being presented.
3.1 Installing Cable Gland with Power Cable and RJ45
UTP Cable
The cable gland consists of the following:
3.2 Connecting Waterproof Cable Kit to the Outdoor
PoE Injector
Step 1: Turn clockwise to tighten the gland body connected to the
Outdoor PoE Injector.
2. Hardware Introduction
This section describes the functionalities of the outdoor PoE Injector’s
components.
2.1 Product Outlook
Unit: mm
PoE-
in-Use
PoE
++
Data
IPOE-175
PWR
DC Input Range:
24-56V , 4A max.
V+
Figure 2-1: IPOE-175 product outlook
2.4 LED Indicators
LED Color Function
PWR Green Indicates it has power.
PoE-in-Use Amber
Indicates the port is providing 55V DC in-line
power.
To install the 2-pin Terminal Block Connector on the Outdoor PoE
Injector, simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power wire
into V-, and grounding wire into Ground.
V+
V
-
2-pin
Step 2: Tighten the wire-clamp screws for preventing the wires from
loosening and plug them into the Wall-mount Gigabit Ethernet
Router.
Note
1. The wire gauge should be in the range from 20 to 22
AWG.
2. The device must be grounded.
Step 2: Plug the power cable connector into the power input port.
Step 3: Insert the sealing insert into the cable gland body.
Step 4: Attach the clamping nut to the cable gland to complete the
cable assembly.
Note
1. Use only the waterproof cable gland provided in the
package of the IPOE-175.
2. If the above installation procedure is not properly
followed, the warranty will be invalidated.
11.31mm
40.78mm
5.00mm
30.22mm
29.80mm
20.18
13.72
14.00
30.10
3. If the waterproof cable gland is found missing or
damage, please contact your local reseller where you
purchased from.
4. Never use any waterproof cable gland that is not
purchased from PLANET or doesn’t have the same
dimensions of the IPOE-175; it will damage the device
permanently.
3.3 Wall-mount Installation
To install the Outdoor PoE Injector on the wall, please follow the
instructions described below.
Step 1: Find the wall that you want to mount the Outdoor PoE Injector
on.