User's Manual

ManualsBrandsPLANET Technology ManualsIndustrial EthernetIndustrial Single-Port 10/100/1000Mbps 802.3bt PoE++ Splitter

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial 802.3bt PoE++

Splitter, IPOE-173S. “PoE Splitter” mentioned in this manual refers

to the IPOE-173S.

Open the box of the PoE Splitter and carefully unpack it. The box

should contain the following items:

PoE Splitter x 1 User’s Manual x 1 RJ45 Dust Cap x 2

DIN-rail Bracket w/Screws kit

x 1

Wall-mount Plate w/Screws kit

x 1

If any of these are missing or damaged, please contact your dealer

immediately.

2.2 4-pin Power Output Terminal Block

If there is no power socket in your network environment, PLANET

IPOE-173S provides DC power for this Ethernet device conveniently.

The IPOE-173S splits the transmission of the power and data.

From top to down, there are Negative (V-), Negative (V-), Positive

(V+) and Positive (V+), and two sets of DC power output contact.

Power Output

V+

12V

12V 24V

DC Voltage

24V

Figure 2-2: Terminal Block of IPOE-173S

Note

It comes with two DC outputs --12V, 5.8A or 24V,

2.9A, totaling 70 watts of DC output power, which

means that DC1 + DC2 cannot be over the 70-watt

DC output power limit. Otherwise, it might cause the

power output to malfunction or damage.

Step 5: Connect the network copper cable (RJ45) from an

802.3bt PoE++ PSE to the IPOE-173S Splitter where the

power and data are separately transmitted to a PD as

shown in the gure below:

Non-PoE

Device

802.3bt PoE++

PSE

802.3bt PoE++ Data in

Data Out

DC+

10/100/1000T Copper

Caution

Make sure the IPOE-173S output voltage (DC

12V/24V) is correct before applying power to a remote

device.

3. Installation

 Wiring the Power Outputs

Please follow the steps below to insert the power wires.

Step 1: Please nd one terminal block connector within two DC

power outputs shown below:

1 V-

DC Output 1

DC Output 2

2 V-

3 V+

4 V+

Note

The wire gauge for the terminal block should be in the

range of 12 ~ 24 AWG.

2. Hardware Introduction

2.1 Front Panel and LED Indicators

The front panels of the Industrial PoE+ Injector Hubs consist of

Ethernet interfaces and LED indicators.

PoE IN

10/100/1000T

Power Output

V+

Data Out

12V

12V 24V

DC Voltage

24V

30W 60W 90W

Industrial 802.3bt PoE++ Splitter

PoE Input

Figure 2-1:

Front View of IPOE-173S

 PoE input indicators

LED Color Function

30W Green

Lights to indicate the

PoE Splitter is working in

802.3at PoE mode.

60W Green

Lights to indicate the

PoE Splitter is working in

802.3bt type 3 PoE mode.

90W Green

Lights to indicate the

PoE Splitter is working in

802.3bt type 4 PoE mode.

 DC output voltage indicators

LED Color Function

12V Amber

Lights to indicate the PoE

Splitter’s output is in 12V

DC mode

24V Green

Lights to indicate the PoE

Splitter’s output is in 24V

DC mode

2.3 DC Voltage DIP Switch

It provides two kinds of DC power output through its DIP switch

and its voltage and current are shown below:

Power Output

V+

12V

12V 24V

DC Voltage

24V

Figure 2-3: DIP Switch of IPOE-173S

Caution

1. Please check the power requirements of the device

carefully that is going to get the power from the

IPOE-173S.

2. If the power requirement is higher than the IPOE-

173S can supply, current overload might shut down

the IPOE-173S itself. Thus, it will also shut down

your device as well.

3. Please ensure the output voltage is correct for

remote device. Otherwise, it will damage your

remote device.

Caution

Do not switch on/off the Power DIP during operation.

Otherwise, it will damage your IPOE-173S and remote

device. If you want to switch from one output voltage

to another via DIP switch, plug out the “PoE In”

cable and wait for 3 seconds until the PoE Input LEDs

are completely OFF.

Step 2: Insert the Negative/Positive DC wires into the V– / V+

terminal; Terminals 1 and 3 for Power 1; Terminals 2 and

4 for Power 2.

Step 3: Connect the other end of DC power wires to the power

devices. Tighten the wire-clamp screws for preventing the

wires from loosening.

Power Output

V+

12V

DC Voltage

24V

Power Output

12V

DC Voltage

24V

V+

Power Output

V+

12V

12V 24V

DC Voltage

24V

Power Output

12V

DC Voltage

24V

V+

Maximum Output 70 Watts

Powered

Device

Total Maximum

Output 70 Watts

Powered

Device

Powered

Device

Step 4: Install the terminal block on PLANET IPOE-173S Splitter.

4.ProductSpecications

Product IPOE-173S

Hardware Specications

Interface

PoE Input Port 1 10/100/1000 BASE-T RJ45

Data Output

Port

1 10/100/1000 BASE-T RJ45

DC Out Plug

Connector

1 removable 4-pin terminal block

DIP Switch 12V/24V DC output

LED Indicators

PoE Input:

30W (Green)

60W (Green)

90W (Green)

DC Voltage:

12V (Amber)

24V (Green)

Data Rate 10/100/1000Mbps

Dimensions (W x D x H) 32 x 87.8 x 135 mm

Weight 445g

Installation DIN-rail/wall mountable

Enclosure IP30 metal case

Power Requirements

802.3bt PoE++ or 4-pair 802.3at

PoE+

PoE DC 48 ~ 56V

Summary of content (2 pages)

PAGE 1
2.2 4-pin Power Output Terminal Block Thank you for purchasing PLANET Industrial 802.3bt PoE++ Splitter, IPOE-173S. “PoE Splitter” mentioned in this manual refers to the IPOE-173S. If there is no power socket in your network environment, PLANET IPOE-173S provides DC power for this Ethernet device conveniently. The IPOE-173S splits the transmission of the power and data. Open the box of the PoE Splitter and carefully unpack it.
PAGE 2
802.3 bt PoE++ 4-pair UTP Cat. 5e, 6, up to 100m input (328ft) (60W+) 48.80 12V 24V 24V DC Voltage V+ 1/2 (+), 3/6 (-); 4/5 (+), 7/8 (-) or 1/2 (-), 3/6 (+); 4/5 (+), 7/8 (-) 32.00 12V Power Pin Assignment Industrial 802.3bt PoE++ Splitter Power Output End-span + Mid-span End-span Mid-span V+ PoE Power Supply Type 97.10 135.00 10/100/1000T DC 12V/24V by DIP switch control Data Out Power Output 10/100/1000T 802.3 bt PoE++ 4-pair 802.3at PoE+ PoE IN PoE Standard 87.