IPOE-171-Series (V3) User Manual

- 9 -
- 10 -
- 11 - - 13 -
- 12 - - 14 - - 15 -
Step 1: Insert Positive / Negative DC power wires into Contacts 1
and 2 for POWER 1, or 5 and 6 for POWER 2.
Max. fault loading: 24V, 1A
V1+
V2+
PWR1
PWR2Fault
DC Input:
12-48V , 5A max.
1 2 3 4 5 6
Figure 5: Power input pins.
Step 2: Tighten the wire-clamp screws for preventing the wires
from loosening.
1 2 3 4 5 6
Power 1 Fault Power 2
+ - + -
Figure 6: PWR1 & PWR2 Pins of Terminal Block.
Note
1. The wire gauge for the terminal block should be in
the range between 12 ~ 24 AWG.
2. As the DC input connector of the IPOE-171 series is
polarity protected, connecting Positive / Negative DC
power wires to the wrong pins will not damage the
unit.
4. Mounting Installation
This section describes how to install the industrial device and make
connections to it. Please read the following sections and perform
the procedures in the order being presented.
Note
In the installation steps below, this manual uses
PLANET Industrial Switch as an example. The steps for
PLANET Industrial Slim-type Switch, Industrial Media/
Serial Converter and Industrial PoE devices are similar.
4.1 DIN-rail Mounting Installation
1
2
4.2 Wall-mount Plate Mounting
3.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. After inserting the wires,
the IPOE-171 series will detect the fault status of the power failure
and then form an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
Figure 7: Fault Pin of Terminal Block.
Note
1. The wire gauge for the terminal block should be in
the range between 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A
currents.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
Figure 8: Fault Alarm Contact
5. Hardware Installation
The following section describes the hardware features of the IPOE-
171 series. Before connecting any network device to it, please read
this chapter carefully.
5.1 Before Installation
Before your installation, it is recommended to check your network
environment. If there is any IEEE 802.3bt device that needs to
be powered on and works normally, the IPOE-171 series is the
solution that supplies power to this Ethernet device conveniently
and easily. If there is diculty in nding a power socket for the
AC-DC connection to your non-IEEE 802.3at/bt networked device,
the IPOE-171 series with POE-172S / IPOE-171S can supply DC
power to this Ethernet device conveniently and easily.
Note
1. In the installation steps below, this manual uses
the IPOE-171-60W as an example. Except the input
voltage, the steps for the IPOE-171-95W are similar.
2. Note that the input power range of the IPOE-
171-60W is 52 ~ 56V DC and the input power
range of IPOE-171-95W is 12 ~ 48V DC.
5.2 IPOE-171-60W Installation
1. Connect the power ranging from 52V DC to 56V DC to the 6-pin
terminal block of the IPOE-171-60W. The power LED will be
steadily on.
2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to “Ethernet” port of the IPOE-171-60W.
3. Connect the long cable to the “Ethernet+DC” port.
4. Connect with IEEE 802.3af/at/bt devices. Due to the capability of
IEEE 802.3af/at/bt Power over Ethernet, the IPOE-171-60W can
directly connect with any IEEE 802.3at/bt end-nodes, such as
PTZ (Pan, Tilt & Zoom) IP cameras, PTZ speed dome cameras,
color touch screens, Voice over IP (VoIP) telephones and multi-
channel wireless LAN access points which support IEEE 802.3af/
at/bt In-line Power over Ethernet port.
IPOE-171 Series
Industrial
Switch
Power
Supply
Data
100 meters
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power
Data
PoE PTZ
IP Camera
PoE
Power
DC Input
DC
-40
75
Figure 9: Connecting architecture with IEEE 802.3at/bt device
Once the IPOE-171-60W detects the existence of an IEEE 802.3at/
bt device, the PoE-in-Use LED indicator will be steadily on to show
it is providing power.
Note
1. According to IEEE 802.3at/bt Power over Ethernet,
the IPOE-171-60W will not inject power to the cable
if not connected to IEEE 802.3at/bt device.
2. Depending on the length of cable, the PoE power
which PD receives is different.
6. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to check if
it could solve your issue. If you need more support information,
please contact PLANET support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq?method=category&c1=2
Support team mail address:
support@planet.com.tw
Copyright © PLANET Technology Corp. 2019.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
FCC Warning
This device has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the Instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
WEEE Warning
To avoid the potential eects on the environment and
human health as a result of the presence of hazardous
substances in electrical and electronic equipment, end
users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do
not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.