User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial IEEE 802.3at High
Power over Ethernet Injector, IPOE-162. The “802.3at PoE+
Injector” mentioned in this User’s Manual refers to the IPOE-
162.
Open the box of the Industrial IEEE 802.3at High Power over
Ethernet Injector and carefully unpack it. The box should
contain the following items:
IPOE-162:
 Industrial IEEE 802.3at Gigabit High Power over Ethernet
Injector x 1
 User’s Manual x 1
 DIN-rail Kit x 1
 Wall-mount Kit x 1
 Dust Cap x 2
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.
2. Product Features
Interface
 2 RJ45 interfaces
 1-port Data + Power output
 1-port Data input
 One terminal block for master and slave power input. (Power
Range: 12 ~ 48V DC redundant power.)
LED Indicator
System:
Power 1 (Green),
Power 2 (Green),
Fault (Red)
PoE Port:
PoE-in-use x 1 (Orange)
Network Cable
10BASE-T: UTP Cat. 3, 4, 5, up to
100m (328ft)
100BASE-TX: UTP Cat. 3, 4, 5, up
to 100m (328ft)
1000BASE-T: UTP Cat. 5, 5e, 6 up
to 100m (328ft)
EIA/TIA-568 100-ohm STP (100m)
Data Rate 10/100/1000Mbps
Dimensions (W x D x H) 32 x 87 x 135 mm
Weight 489g
Unit Input Voltage 12 ~ 48V DC
Power Consumption 32 watts max.
Number of devices that
can be powered
1
Installation DIN-rail kit and wall-mount ear
Alarm
Provides one relay output for
power failure; alarm relay current
carry ability: 3A @ DC 24V
Enclosure IP30 slim metal case
Power over Ethernet
PoE Standard
IEEE 802.3at High Power over
Ethernet/mid-span PSE
PoE Power Output 30 watts
PoE Power Supply Type Mid-span
Power Pin Assignment 4/5(+), 7/8(-)
LED Indicators
LED Color Function
P1 Green Indicates Power 1 has power.
P2 Green Indicates Power 2 has power.
FAULT Red
Indicates either Power 1 or Power 2
has no power.
PoE-in-Use Orange
Indicates the port is providing 56V
DC in-line power.
4.3 Industrial PoE+ Injector Upper Panel
The upper panel of the Industrial PoE+ Injector consists of one
terminal block connector within two DC power inputs. Figure 1
shows the upper panel of the Industrial PoE+ Injector.
Input
DC 12~48V
V1+ V1- V2+ V2-
PWR1
PWR2Fault
1 2 3 4 5 6
Figure 4-3: Industrial PoE+ Injector Upper Panel
4.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial PoE+ Injector is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
4. Hardware Description
4.1 Physical Dimensions
32.00
135.00
87.80
97.10
48.8046.50
39.70
28.00
48.80
53.50
53.50
18.00
15.20
30.00
9.20
135.00
87.80
87.80
40.00
28.0018.00
28.00
18.0028.00
28.00
40.00
28.00
10/100/1000T 10/100/1000T
Ethernet+DC
Ethernet
PoE
In-Use
IPOE-162
P1 P2 FAULT
802.3at
Input
DC 12~48V
V1+ V1- V2+ V2-
PWR1
PWR2Fault
Top View
Side View Front View
Mounting Kit Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Figure 4-1: IPOE-162 dimensions
PoE
 Gigabit High Power over Ethernet mid-span PSE
 IEEE 802.3at/802.3af PoE compliant
 IEEE 802.3at/802.3af splitter devices compatible
 Supports PoE Power up to 30 watts for the PoE port
 Provides DC 56V power over RJ45 Ethernet cable to device
with Ethernet port
 Auto-detection of PoE IEEE 802.3at/802.3af devices
 Remote power feeding up to 100m
Hardware
 IP30 slim metal case
 LED indicators for power LED and PoE-in-use
Industrial Case and Installation
 DIN-rail and wall-mount designs
 Supports 6000 VDC Ethernet ESD protection
 -40 to 75 degrees C operating temperature
3.ProductSpecications
Product IPOE-162
Hardware Specications
Hardware Version 3
Interface
Input Port 1 x RJ45 STP (Data In)
Output Port 1 x RJ45 STP (Data + Power Out)
Input Power
Terminal Block
1
Standards Conformances
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet
Plus
FCC FCC Part 15B Class A
CE
EMI
EN 55022
EN 61000-3-2
EN 61000-3-3
EMS
EN 61000-4-2 (ESD)
EN 61000-4-3 (RS)
EN 61000-4-4 (EFT)
EN 61000-4-5 (Surge)
EN 61000-4-6 (CS)
EN 61000-4-8 (PFMF)
Stability Testing
IEC60068-2-32(Free fall)
IEC60068-2-27(Shock)
IEC60068-2-6(Vibration)
Environment
Operating Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
Note
The PoE power output ability will depend on the
distance.
4.2 Product Outlook
Figure 4-2: IPOE-162 outlook
1. Insert the positive and negative DC power wires into
Contacts 1 and 2 for Power 1, or 5 and 6 for Power 2.
Input
DC 12~48V
V1+ V1- V2+ V2-
PWR1
PWR2Fault
1 2 3 4 5 6
Figure 4-4: Power Input Pins
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4 5 6
Power 1 Fault Power 2
+ - + -
Figure 4-5: PWR1 & PWR2 Pin of Terminal Block
Note
The wire gauge for the terminal block should be in
the range of 12 to 24 AWG.