User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET compact industrial 100/1000X
to 10/100/1000T 802.3bt PoE++ Media Converter series, IGUP-
1205AT and IGUP-2205AT. In the following section, the term
“Industrial PoE++ Media Converter” means the IGUP-1205AT
or IGUP-2205AT.
Open the box of the Industrial PoE++ Media Converter and carefully
unpack it. The box should contain the following items:
1. Industrial PoE++ Media Converter x 1
2. User’s Manual x 1
3. DIN-rail Kit
4. Wall-mount Kit
5. Dust Cap (Please refer to the table below.)
RJ45 Dust Cap SFP Dust Cap
IGUP-1205AT 1 2
IGUP-2205AT 2 2
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Weight 612 g 665 g
Power
Requirements
12-56V DC, supports reverse polarity
protection
Power
Consumption
System ON without
loading
12V DC: 4.56W
48V DC: 5.28W
Full loading with PoE
12V DC: 46.6W
48V DC: 100.3W
System ON without
loading
12V DC: 4.56W
48V DC: 5.28W
Full loading with PoE
12V DC: 67.44W
48V DC: 205W
DIP Switch Standard/Legacy mode
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV DC
Cables
10/100/1000BASE-T:
2-pair UTP Cat. 3, 4, 5, 5e, 6
(maximum 100 meters)
EIA/TIA-568 100-ohm STP
(maximum 100 meters)
100BASE-FX/1000BASE-SX/LX:
Multi-mode: 50/125μm or 62.5/125μm
optical ber
Single-mode: 9/125μm optical ber
Power Over Ethernet
PoE Standard IEEE 802.3bt Power over Ethernet Plus Plus
PoE Power Output
Standard (BT) mode: 90W
Legacy (PoH) mode: 95W
 Front View
P1 P2 Fault
30W 60W 90W
3
2
1
IGUP-1205AT
802.3bt PoE
++
LNK ACT
PoE-in-Use
LNK ACT
LNK
1000
100 ACT
Standard Legacy
P1 P2 Fault
60W 120W 180W
Standard Legacy
4
3
1
IGUP-2205AT
802.3bt PoE
++
LNK ACT
PoE-in-Use
LNK ACT
LNK
1000
100 ACT
2
Figure 3: IGUP-1205AT/IGUP-2205AT Front View
3. Hardware Introduction
3.1 Three-View Diagram
The three-view diagram of the Industrial PoE++ Media Converter
consists of Ethernet interfaces and one removable 6-pin terminal
block. The LED indicators are also located on the front panel.
50.00
87.80
97.10
48.8047.30 38.90
135
15.2
9.2
56
3.00
107.00 [4.21]
28.00 [1.10]
18.00 [0.71]
40.00 [1.57]
50.00 [1.97]
18.00 [0.71]
40.00
50.00
48.80
50.00
P1 P2 Fault
30W 60W 90W
3
2
1
IGUP-1205AT
802.3bt PoE
++
LNK ACT
PoE-in-Use
LNK ACT
LNK
1000
100 ACT
Standard Legacy
Top View
Side View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Bottom View
Max. fault loading: 24V, 1A
V1+
V2+
PWR1
PWR2Fault
DC Input: 12-56V , 6A max.
Figure 1: IGUP-1205AT Three-View Diagram
2.ProductSpecications
Model IGUP-1205AT IGUP-2205AT
Hardware Specications
Copper Port
1 x
10/100/1000BASE-T
2 x
10/100/1000BASE-T
SFP Slots
2 x 1000BASE-SX/LX/BX SFP interface
Compatible with 100BASE-FX SFP
Flow Control
Back pressure for half duplex mode
IEEE 802.3x pause frame for full duplex
mode
Maximum Frame
Size
9K
LED
System:
Power 1 (Green), Power 2 (Green), Fault
Alarm (Red)
PoE Usage:
IGUP-1205AT: 30W/60W/90W (Amber)
IGUP-2205AT: 60W/120W/180W (Amber)
Fiber:
100BASE-X: LNK/ACT (Amber)
1000BASE-X: LINK/ACT (Green)
TP:
10/100/1000BASE-T: LNK/ACT (Green)
PoE: PoE-in-Use (Amber)
Dimensions
(W x D x H)
55 x 85 x 135 mm
PoE Power Supply
Type
End-span + Mid-span
Power Pin
Assignment
End-span: 1/2 (-), 3/6 (+);
Mid-span: 4/5 (+), 7/8 (-)
PoE Power Budget
95 watts@ 24-56V DC input
30 watts@ 12V DC input
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Protocols and
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber Optic
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3bt Power over Ethernet Plus Plus
IEEE 802.3az Energy Ecient Ethernet (EEE)
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
135
15.2
9.2
56
50.00
87.80
97.10
48.8047.30 38.90
3.00
107.00 [4.21]
28.00 [1.10]
18.00 [0.71]
40.00 [1.57]
50.00 [1.97]
18.00 [0.71]
40.00
50.00
48.80
50.00
P1 P2 Fault
60W 120W 180W
Standard Legacy
4
3
1
IGUP-2205AT
802.3bt PoE
++
LNK ACT
PoE-in-Use
LNK ACT
LNK
1000
100 ACT
2
Top View
Side View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Bottom View
Max. fault loading: 24V, 1A
V1+
V2+
PWR1
PWR2Fault
DC Input: 12-56V , 6A max.
Figure 2: IGUP-2205AT Three-View Diagram
3.2 LEDDenition:
■System
LED Color Function
P1 Green
Lights to indicate DC power input 1 has
power.
P2 Green
Lights to indicate DC power input 2 has
power.
Fault Red Lights to indicate that DC power has failed.
PoE Usage Amber
IGUP-1205AT (30W, 60W, 90W)
Lights to indicate the system consumes
over 30-/60-/90-watt PoE power budget.
Blinks to indicate the system consumes less
30-/60-/90-watt PoE power budget.
IGUP-2205AT (60W, 120W, 180W)
Lights to indicate the system consumes
over 60-/120-/180-watt PoE power budget.
Blinks to indicate the system consumes less
60-/120-/180-watt PoE power budget.
■GigabitTPInterface
LED Color Function
TP
LNK/ACT
Green
Lights to indicate that the copper port is
successfully connecting to the network at
10/100/1000Mbps.
Blinks to indicate the copper port is
receiving or sending data.
PoE-in-Use Amber
Lights to indicate that the port is providing
54V DC to remote powered device.
O to indicate that the port is not providing
54V DC to remote powered device.