User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
 PoE
LED Color Function
PoE-in-Use Amber
Lit: Lit: Indicates that the port is providing
PoE power to remote powered device.
O: Indicates that the port is not providing
PoE power to remote powered device.
3.3 Wiring the Power Inputs
The terminal block connector on the top panel of Industrial PoE+
Media Converter is used for 12~48V DC power inputs. Please follow
the steps below to insert the power wire.
Caution
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.
1. Insert positive and negative DC power wires into contacts 1 and
2 for POWER 1, or 5 and 6 for POWER 2.
Max. Fault Alarm Loading: 24V, 1A
V1+
V2+
PWR1
PWR2Alarm
DC Input: 12-48V
, 3A max.
AC Input: 24V
, 1.5A max.
1 2 3 4 5 6
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
Note
1. The wire gauge for the terminal block should be in
the range of 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A
currents.
3.5 Grounding the Device
Users MUST complete grounding wired with the device; otherwise,
a sudden lightning could cause fatal damage to the device. EMD
(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.
Max. Fault Alarm Loading: 24V, 1A
V1+
V2+
PWR1
PWR2Alarm
DC Input: 12-48V
, 3A max.
AC Input: 24V
, 1.5A max.
1 2 3 4 5 6
Earth Ground
4. Hardware Installation
This section describes the functionalities of the Industrial PoE+
Media Converter’s components and guides you to installing it on
the DIN rail and wall. Please read this chapter completely before
continuing.
Note
This following picture tells the user how to install the
device, and the device is not IGTP-80xT series.
1 2 3 4 5 6
Power 1 Alarm Power 2
+ - + -
Note
1. The wire gauge for the terminal block should be in
the range between 12 and 24 AWG.
2. The DC power input range is 12V ~ 48V DC and
supports 24V AC.
3. Please just use one power input when using 24V AC.
3.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial PoE+ Media Converter will detect the fault status of
the power failure, and then forms an open circuit. The following
illustration shows an application example for wiring the fault alarm
contacts.
Fault Alarm Contacts
Alarm
1 2 3 4 5 6
The Fault Alarm Contacts are energized
(CLOSE) for normal operation and will
OPEN when failure occurs
4.1 DIN-rail Mounting Installation
1
2
4.2 Wall-mount Plate Mounting
4.3 Side Wall-mount Plate Mounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
5. Link Fault Passthrough
The LFP function includes Link Loss Carry Forward (LLCF), Link
Loss Return (LLR) and the DIP switch design. LLCF and LLR can
immediately alarm administrators the issue of the link media
and provide ecient solution to monitor the net. The DIP switch
provides the disabling or enabling of the LFP function.
IP Camera
LFP
Enabled
LFP
Enabled
Copper Cable Copper Cable
Monitoring Center
IP Camera
Fiber Cable
LFP
Enabled
LFP
Enabled
Copper Cable
Copper Cable
Monitoring Center
Copper Link Broken
1
Copper
Link Down
5
LFP disconnects
Fiber Link
2
LFP disconnects
Copper Link
4
Fiber Link Down
3
1000
1000
Fiber Cable
Remote Link
Broken
Remote Link
Normal
1000BASE-SX/LX Fiber-optic
1000
1000BASE-T UTP
Note
LFP function is turned off by default. This feature can
also be turned on via the DIP switch. If you are not
familiar with the network installation and for diag-
nostic purpose (i.e. check which end is broken), you
can turn it on. Otherwise, please remain it in the
default position.
Customer Support
Thank you for purchasing PLANET products. You can browse our
online FAQ resource on PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address:
support @planet.com.tw
Copyright © PLANET Technology Corp. 2021
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.