User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET industrial 100/1000X to
10/100/1000T 802.3at PoE+ Media Converter, IGTP-80xT series.
In the following sections, the term “Industrial PoE+ Media
Converter” means the IGTP-80xT series.
Open the box of the Industrial PoE+ Media Converter and carefully
unpack it. The box should contain the following items:
Industrial PoE+
Media Converter x 1
User’s Manual x 1 Wall-mount Kit x 1
DIN-rail Kit x 1 RJ45 Dust Caps x 1 SFP/SC Dust Cap x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Power Over Ethernet
PoE
Standard
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
PoE Power
Output
52V DC: 15.4 watts
52V DC: 30 watts
PoE Power
Supply Type
End-span
Power Pin
Assignment
1/2(+), 3/6(-)
PoE Power
Budget
30 watts
Hardware Specications
Speed
Twisted-pair:
10/20Mbps for half/full duplex
100/200Mbps for half/full duplex
1000/2000Mbps for full duplex
Fiber Optic:
200Mbps/2000Mbps for full duplex (IGTP-805AT)
2000Mbps for full duplex (IGTP-802T/IGTP-802TS)
Flow Control
Back pressure for half duplex mode
IEEE 802.3x pause frame for full duplex mode
Maximum
Frame Size
9K
LED
System: Power 1, Power 2 (Green) and
Alarm LED (Red)
Fiber 1000BASE-X: LNK/ACT (Green)
TP 10/100/1000BASE-T: LNK/ACT, 1000 LNK/ACT
(Green)
PoE: Power-in-use (Amber)
Note
The above drawing is based on IGTP-805AT. The only
difference between the three models is the fiber optic
interface.
 Front Panels
P1 P2
TX
RX
OFF ON
LNK/
ACT
LNK/
ACT
1000
PoE-
in-Use
Alarm
IGTP-802T
1000BASE-SX
LFP
Ethernet+DC
10/100/1000T
802.3at
P1 P2
TX
RX
OFF ON
LNK/
ACT
LNK/
ACT
1000
PoE-
in-Use
Alarm
IGTP-802TS
1000BASE-LX
LFP
Ethernet+DC
10/100/1000T
802.3at
P1 P2
OFF ON
LNK/
ACT
LNK/
ACT
1000
PoE-
in-Use
Alarm
IGTP-805AT
100/1000X
LFP
Ethernet+DC
10/100/1000T
802.3at
Figure 2: IGTP-802T Figure 3: IGTP-802TS Figure 4: IGTP-805AT
Cables
10/100/1000BASE-T:
2-pair UTP Cat. 3, 4, 5, 5e, 6
(maximum 100 meters)
EIA/TIA-568 100-ohm STP
(maximum 100 meters)
100BASE-FX/1000BASE-SX/LX:
Multi-mode: 50/125μm or 62.5/125μm optical ber
Single-mode: 9/125μm optical ber
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Protocols
and
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber Optic
IEEE 802.3x Flow Control
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
Stability
Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
2.ProductSpecications
Product IGTP-802T IGTP-802TS
IGTP-805AT
Ethernet Interface
Copper
10/100/1000BASE-T Ethernet TP interface.
Maximum 100m distance.
Auto-negotiation, auto MDI/MDI-X with PoE injector
function
1000BASE-X
Fiber-optic
Connector
Type
SC SC
SFP (LC)
Supports
1000BASE-SX/LX/BX
and 100BASE-FX SFP
module
Fiber Cable
Multi-mode:
50/125µm
or
62.5/125µm
optic ber
Single-mode:
9/125µm
optic ber
Varying on SFP Module
Fiber Cable
Distance
220m &
550m
20km
Fiber Optic
Frequency
850nm 1310nm
Launch
Power
Max. -3dBm
Min. -10dBm
Max. -3dBm
Min. -9dBm
Receive
Sensitivity
-20dBm -23dBm
Maximum
Input Power
-3dBm -3dBm
Dimensions
(W x D x H)
32 x 87 x 135 mm
Weight 416g 420g
Unit Input
Voltage
12 ~ 48V DC
24V AC
Power
Consumption
System on:
AC 24V: 4.5W/15BTU
DC 12V: 4.6W/15BTU
DC 48V: 4.5W/15BTU
Full Loading:
AC 24V: 23.5W/80BTU
DC 12V: 48W/163BTU
DC 48V: 47.5W/162BTU
System on:
AC 24V: 2.8W/9.5BTU
DC 12V: 2.6W/8.8BTU
DC 48V: 2.8W/9.5BTU
Full Loading:
AC 24V: 23.1W/78BTU
DC 12V: 46.8W/159BTU
DC 48V: 47W/160BTU
DIP Switch
OFF: LFP (Link Fault Passthrough) disable
ON: LFP (Link Fault Passthrough) enable
FEF (Far End Fault) works with LFP to prevent
data loss
LFP is turned o by default on the DIP switch.
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount ear
ESD
Protection
6KV DC
Alarm
Provides one relay output for power failure
Alarm relay current carry ability: 1A @ DC 24V
3. Hardware Introduction
3.1 Three-View Diagram
The three-view diagram of the Industrial PoE+ Media Converter
consists of Ethernet interfaces and one removable 6-pin terminal
block. The LED indicators are also located on the front panel.
 IGTP-805AT/IGTP-802T/IGTP-802TS:
32.00
135.00
87.80
97.10
48.8046.50 39.70
28.00
48.80
53.50 53.50
18.00
15.20
30.00
9.20
40.00
28.0018.00
28.00
18.0028.00
28.00
40.00
163.00
Top View
Side View Front View
Mounting Kit Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Bottom View
P1 P2
OFF ON
LNK/
ACT
LNK/
ACT
1000
PoE-
in-Use
Alarm
IGTP-805AT
100/1000X
LFP
Ethernet+DC
10/100/1000T
802.3at
Max. Fault Alar m Loading: 24V, 1A
V1+
V2+
PWR1
PWR2Alarm
DC Input: 12-48V
, 3A max.
AC Input: 24V
, 1.5A max.
Figure 1: Three-View Diagram
3.2 LEDDenition:
 System
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
Alarm Red
Lit: indicates either power 1 or power 2 has
no power.
 Gigabit Fiber Interface
LED Color Function
Fiber
LNK/ACT
Green
Lit: indicates that the ber optic port is
successfully connecting to the network at
100Mbps or 1000Mbps.
Blinks: Indicates the ber optic port is
receiving or sending data.
 Gigabit TP Interface
LED Color Function
TP
LNK/ACT
Green
Lit: indicates that the Gigabit Ethernet Port
is successfully connecting to the network at
10/100/1000Mbps.
Blinks: indicates the Gigabit Ethernet Port is
receiving or sending data.
TP 1000
LNK/ACT
Lit: indicates that the Gigabit Ethernet Port is
successfully connecting to the network at 1000Mbps.
Blinks: indicates the Gigabit Ethernet Port is
receiving or sending data.
OFF: indicates the Gigabit Ethernet Port is
successfully connecting to the network at
10/100Mbps.