User’s Manual of IGT-90x User’s Manual IGT-902 / 902T IGT-902S / 902TS IGT-905A 10/100/1000Base-T to 1000Base-SX / LX Industrial Managed Media Converter -1-
User’s Manual of IGT-90x Trademarks Copyright © PLANET Technology Corp. 2010. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
User’s Manual of IGT-90x TABLE OF CONTENTS 1. INTRODUCTION .............................................................................................................5 1.1 Package Contents ..................................................................................................................................................... 5 1.2 How to Use This Manual ...........................................................................................................................................
User’s Manual of IGT-90x 4.2.6 Factory Default ................................................................................................................................................. 33 4.2.7 System Reboot ................................................................................................................................................. 35 4.3 Port Management................................................................................................................................
User’s Manual of IGT-90x 1. INTRODUCTION 1.
User’s Manual of IGT-90x 1.3 Product Description The Industrial Managed Media Converter IGT-90X provide conversion between 10/100/1000Base-T and 1000Base-SX /LX network. There are SC / LC connectors and single-mode / multi-mode media for your needs. Ethernet signal that allows two type segments connect easily, efficiently and inexpensively. The Industrial Managed Media Converter equipped with remote Web / SNMP interface.
User’s Manual of IGT-90x 1.
User’s Manual of IGT-90x • Management VLAN ¾ Quality of Service Ingress/Egress Bandwidth control on TP / Fiber port 4 priority queues, strict priority and Weighted Round Robin (WRR) Traffic classification by: • IEEE 802.
User’s Manual of IGT-90x Power Input Power Consumption Operating Temperature Operating Humidity Storage Temperature 12 to 48V DC Redundant power with polarity reverse protection function 7.7 Watts/ 26 BTU (maximum) -10~60 -30~75 -10~60 -30~75 -30~75 Degree C Degree C Degree C Degree C Degree C 5~90% non-condensing -20~85 -40~85 -20~85 -40~85 -40~85 Degree C Degree C Degree C Degree C Degree C Storage Humidity 5~90% non-condensing Dimension (W x D x H) 13.5 x 8.5 x 3.
User’s Manual of IGT-90x 2. HARDWARE INSTALLATION This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Industrial Managed Media Converter and automatically distinguishes the speed of incoming connection. This section describes the functionalities of IGT-90X’s components and guides how to install it on the DIN Rail Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.
User’s Manual of IGT-90x 2.1.1 LED Indicators LED Color P1 P2 FAULT Green Green Green Fiber LNK /ACT Green Function Lit Lit Lit Lights TP 1000 Blinks To indicate the Fiber Optical Port is receiving or sending data. Lights To indicate that the Gigabit Ethernet Port is successfully connecting to the network at 1000Mbps. OFF indicate the Gigabit Ethernet Port is successfully connecting to the network at 10/100Mbps.
User’s Manual of IGT-90x 2.1.3 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Media Converter is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. 2. Tighten the wire-clamp screws for preventing the wires from loosing.
User’s Manual of IGT-90x 2.1.4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Management Media Converter will detect the fault status of the power failure, or port link failure (available for managed model) and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
User’s Manual of IGT-90x 2.2 Mounting Installation This section describes how to install the Industrial Managed Media Converter and make connections to it. Please read the following topics and perform the procedures in the order being presented. In the installation steps below, this Manual use IGS-801(PLANET 8 Port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Switch & Industrial Media / Serial Converter are similar.
User’s Manual of IGT-90x Step 3: Check the DIN-Rail is tightly on the track. Step 4: Please refer to following procedures to remove the Industrial Gigabit Ethernet Switch from the track. Step 5: Lightly press the button of DIN-Rail for remove it from the track. 2.2.2 Wall Mount Plate Mounting To install the Industrial Equipment on the wall, please follows the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Equipment; loose the screws to remove the DIN-Rail.
User’s Manual of IGT-90x Step 3: Use the screws to screw the wall mount plate on the Industrial Equipment. Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Equipment on the wall. Step 5: To remove the wall mount plate, reverse steps above. 2.2.
User’s Manual of IGT-90x Please refers to APPENDIX-A for detailed wiring information of the Industrial Managed Media Converter. To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the Industrial Managed Media Converter. IGT-905A Installation: IGT-905A is with high reliability and flexibility to extend the distance from 220m to 120Km. It depends on the Gigabit mini GBIC modules. The SFP transceivers are hot-plug and hot-swappable.
User’s Manual of IGT-90x MGB-LA10 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,10km MGB-LB10 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,10km MGB-LA20 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,20km MGB-LB20 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,20km MGB-LA40 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1310nm), SM,40km MGB-LB40 SFP-Port 1000Base-LX mini-GBIC module- LC WDM(TX:1550nm), SM,40km MGB-TSX SFP-Port 1000Bas
User’s Manual of IGT-90x 3. INDUSTRIAL MEDIA CONVERTER MANAGEMENT This chapter describes how to manage the Industrial Managed Media Converter. Topics include: - Overview - Management methods - Assigning an IP address to the Industrial Managed Media Converter - Logging on to the Industrial Managed Media Converter 3.1 Overview This chapter gives an overview of Industrial Managed Media Converter management. The IGT-90X provides a simply WEB browser interface.
User’s Manual of IGT-90x 3.3 Management Methods The way to manage the IGT-90X: -Web Management via a network or dial-up connection. -Using SNMP Network Management Station. 3.3.1 Web Management The PLANET Industrial Managed Media Converter provides a built-in browser interface. You can manage the Industrial Managed Media Converter remotely by having a remote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox. Figure 3-1 Web Management over Ethernet 3.3.
User’s Manual of IGT-90x Figure 3-2 Login Web Page screen 1. For security reason, please change and memorize the new password after this first setup. 2. Only accept command in lowercase letter under web interface. 3.3.3 SNMP Management You can manage the Industrial Managed Media Converter across a LAN using an SNMP Network Management Station with a graphical user interface.
User’s Manual of IGT-90x Figure 3-3 Planet Smart Discovery Utility Screen If there are two LAN cards or above in the same administrator PC, choose different LAN card by use the “Select Adapter” tool. 3. Press “Refresh” button for list current connected devices in the discovery list, the screen is shown as follow. Figure 3-4 Planet Smart Discovery Utility Screen 1.
User’s Manual of IGT-90x 3. To click the “Control Packet Force Broadcast” function, it can allow assign new setting value to the Managed Media Converter under different IP subnet address. 4. Press “Connect to Device” button then the Web login screen appears in Figure 3-2. 5. Press “Exit” button to shutdown the planet Smart Discovery Utility.
User’s Manual of IGT-90x 4. WEB MANAGEMENT The IGT-90X Industrial Managed Media Converter provide remote Web interface for management function configuration and make the Industrial Managed Media Converter operate more effectively - They can be configured through the Web Browser. A network administrator can manage and monitor the Industrial Managed Media Converter from the local LAN. This section indicates how to configure the Industrial Managed Media Converter to enable its management function. 4.
User’s Manual of IGT-90x 4.2 System 4.2.1 System Information The System Information Web page provides information for the current device. System Information Web page helps network administrator to identify the firmware versions, IP Subnet Address and etc. The screen in Figure 4-2 appears and Table 4-1 describes the System Information object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.2.2 IP Configuration The IP Configuration includes the DHCP Client, IP Address, Subnet Mask, Gateway and Description. The screen in Figure 4-3 appears and Table 4-2 describes the IP Configuration object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.2.3 Password Setting This function provides administrator to secure Web login. The screen in Figure 4-4 & 4-5 appears and Table 4-3 describes the Password Setting object of Industrial Managed Media Converter.
User’s Manual of IGT-90x The Password Setting Web page includes the following configurable data: Login Name Displays the user name (admin). Old Password Enter the old password is required before entering the new password. New Password Specifies the new password. The password is not displayed. As it entered an “y” corresponding to each character is displayed in the field. (The maximum length is 16 characters) Confirm This confirms the new password.
User’s Manual of IGT-90x Figure 4-7 Firmware Upgrade Web page screen After find the firmware location from administrator PC, press “Upgrade” button to start the firmware upgrade process. The screen in Figure 4-8 & 4-9 appears. Figure 4-8 Firmware Upgrade Web page screen Do not power off the converter until the update progress is complete. Do not quit the Firmware Upgrade page without press the “Upgrade” button - after the image is loaded. Or the system won’t apply the new firmware.
User’s Manual of IGT-90x Figure 4-9 Firmware Upgrade Web page screen When firmware upgrade process is completed then the following screen appears, please click “here” to re-login the IGT-90X with latest firmware and the screen in Figure 4-10 & 4-11 appears.
User’s Manual of IGT-90x Figure 4-11 Login Web page screen 4.2.5 SNMP Management This function provides SNMP Management and SNMP Trap Receiver Configuration function of the Industrial Managed Media Converter and the screen in Figure 4-12 & 4-13 appears and Table 4-4 & 4-5 describes the SNMP Management and SNMP Trap Receiver object of Industrial Managed Media Converter.
User’s Manual of IGT-90x The SNMP Management Web page includes the following configurable data: SNMP Agent Allow disable or enable the SNMP Agent function, the default mode is “Disable”. SNMP Read Community Allow input the characters for SNMP Read Community, up to maximum 16 characters allow. SNMP Write Community Allow input the characters for SNMP Write Community, up to maximum 16 characters allow. System Name Allow input the characters for System Name, up to maximum 16 characters allow.
User’s Manual of IGT-90x Link Up When TP or Fiber port connection is build up, the administrator PC (SNMP Trap Destination) will receive a Link Up Trap. Link Down When TP or Fiber port connection is Disconnect, the administrator PC (SNMP Trap Destination) will receive a Link Down Trap. Apply Button Press “Apply” button for save current configuration of IGT-90X Table 4-5 Descriptions of the SNMP Trap Receiver Configuration Web Page Screen Objects 4.2.
User’s Manual of IGT-90x Figure 4-15 Factory Default Web page screen Figure 4-16 Login Web page screen -34-
User’s Manual of IGT-90x 4.2.7 System Reboot This function provides System Reboot function of the Industrial Managed Media Converter and the screen in Figure 4-17 & 4-18 & 4-19 appears.
User’s Manual of IGT-90x Figure 4-19 Login Web page screen -36-
User’s Manual of IGT-90x 4.3 Port Management 4.3.1 Port Configuration This function allows displaying TP / Fiber port status. The Link Status in the screen displays the current connection speed and duplex mode; else this function will show red “Down” when the TP / Fiber port is disconnected. Press the “Refresh” button to renew the screen. The screen in Figure 4-20 appears and Table 4-6 describes the Port Configuration object of IGT-90X.
User’s Manual of IGT-90x Disable: No Flow Control or backpressure function on no matter Full-Duplex or Half-Duplex mode Default mode: Disable Ingress Rate Limit The value of inbound traffic limitation in kilobit-per-second (kbps). The available options are : • No Limit • 512K • 1M • 2M • 4M • 8M • 10M • 50M • 100M • 500M Default mode: No Limit The Ingress Rate Limit configuration field as show in Figure 4-21. Egress Shaping The value of outbound traffic limitation in kilobit-per-second (kbps).
User’s Manual of IGT-90x Figure 4-21 Port Configuration-Ingress Rate Limit Web Page screen Figure 4-22 Port Configuration-Egress Shaping Web Page screen -39-
User’s Manual of IGT-90x 4.3.2 Port Status This function allows displaying TP / Fiber port detail status, such as Link Status, Duplex Mode, Flow control, Speed and Auto negotiation. Press the “Refresh” button to renew the screen, the screen in Figure 4-23 appears and Table 4-7 describes the Port Status object of Industrial Managed Media Converter. Figure 4-23 Port Status Web Page screen The Port Status Web page includes the following configurable data: Port Indicate the TP port and Fiber port.
User’s Manual of IGT-90x 4.3.3 Port Statistics This function allows displaying TP / Fiber port detail statistics, press the “Clear” button to clear current counter information. Press the “Refresh” button to renew the screen, the screen in Figure 4-24 appears.
User’s Manual of IGT-90x 4.4 Converter Configuration This function provides useful setting for the IGT-90X as Maximum Packet length, Loop detection, storm control and etc. The screen in Figure 4-25 appears and Table 4-8 describes the Converter Configuration object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 200ms 100ms Default mode is 800ms. Apply Button Press this button for save current configuration of Managed Media Converter. Table 4-8 Descriptions of the Converter Configuration Web Page Screen Objects 4.5 VLAN A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members.
User’s Manual of IGT-90x 802.1Q Tag User Priority 3 bits TPID (Tag Protocol Identifier) 2 bytes Preamble Destination Address Source Address 6 bytes CFI 1 bits 12 bits TCI (Tag Control Information) 2 bytes Ethernet Type VLAN TAG 6 bytes VLAN ID (VID) 4 bytes 2 bytes Data FCS 46-1500 bytes 4 bytes The Ether Type and VLAN ID are inserted after the MAC source address, but before the original Ether Type/Length or Logical Link Control.
User’s Manual of IGT-90x Default VLANs The Industrial Managed Media Converter initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the Industrial Managed Media Converter to the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed from the "default." 4.5.1 VLAN Group This function allows disable or enable the IEEE 802.1Q VLAN operation mode.
User’s Manual of IGT-90x Figure 4-27 VLAN Group Web Page screen The VLAN Group Web page includes the following configurable data: VLAN Mode Provide Disable or enable the IEEE 802.1Q VLAN operation mode. Default mode is Disable. Management VLAN Group Provide define the Management VLAN group. Default mode is VLAN1. VLAN Group Indicate the VLAN Group from 1 to 16. VID Provide define the VLAN Group ID and the available options are 1 to 4094.
User’s Manual of IGT-90x 4.5.2 VLAN Per Port Setting This function provides IEEE 802.1Q VLAN per port setting for TP and Fiber port of IGT-90X. Press the “Apply” button to save the current configuration of IGT-90X. The screen in Figure 4-28 appears and Table 4-10 describes the VLAN Per Port Setting object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.5.3 Q-in-Q VLAN Setting When enable Q-in-Q function, IGT-90X can insert or remove 4-bytes Q-in-Q tag in the received 802.3 frames after SA. User can define Q-in-Q tag value freely. And in default condition, Q-in-Q tag format is same as VLAN tag. In normal application, enable two port’s Q-in-Q function. UTP Port set to insert Q-in-Q tag and Fiber port set to remove Q-in-Q Tag.
User’s Manual of IGT-90x 4.6 Quality of Service Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific, time critical, and file-backup traffic. QoS reduces bandwidth limitations, delay, loss, and jitter.
User’s Manual of IGT-90x The Quality of Service Web page includes the following configurable data: QoS Mode Provide 4 different QoS mode for operation, the available options are: Disable 802.1p Tag Priority The 802.1p Tag Priority field as show in Figure 4-31. IP Address Priority The IP Address Priority field as show in Figure 4-32. IP DSCP Priority The IP DSCP Priority field as show in Figure 4-33. Default mode is Disable.
User’s Manual of IGT-90x Figure 4-32 IP Address Priority Web Page screen Figure 4-33 IP DSCP Priority Web Page screen -51-
User’s Manual of IGT-90x On the top of DSCP Value table have two could be set. The default DSCP value is 63. These two fields are both for customize DSCP value. 4.7 OAM Setup 4.7.1 Local TS-1000 OAM Setup This function provides Local TS-1000 OAM Setup of IGT-90X. Press the “Apply” button to save the current configuration of Industrial Managed Media Converter. The screen in Figure 4-34 appears and Table 4-13 describes the Local TS-1000 OAM Setup object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.7.2 Remote TS-1000 OAM Setup The Remote TS-1000 OAM Setup is an advanced remote device monitor feature that allows you to remote monitor and automatic notify status indication. Remote monitor 1. User instructs center Media Converter to issue a status notification request frame defined in TS-1000 to get status of terminal Media Converter. 2.
User’s Manual of IGT-90x Figure 4-36 IGT-90X Remote TS-1000 OAM Setup Web Page screen Please use the PLANET GT-80X / GT-90X / IGT-90X as the Remote device.
User’s Manual of IGT-90x 4.7.3 TS-1000 Loop Back Test The TS-1000 Loop Back Test allows manual run this loop back test to check the interconnection between two Industrial Media Converter devices. To assure the Remote TS-1000 OAM function can work correctly. In-band and out-band Loop back 1. Instruct center Industrial Media Converter to issue an OAM frame to request a loop back test. Terminal return start response OAM frame to center Media Converter. 2. Terminal Media Converter runs at loop back mode. 3.
User’s Manual of IGT-90x Figure 4-37 Remote TS-1000 Loop Back Test Web Page screen The TS-1000 Loop Back Test Web page includes the following configurable data: TS-1000 Loop Back Test Send Packet Number Allow input the number for packet send and the available options is 1 to 255. Default is 16. Apply Button Press this button for save current configuration of Industrial Managed Media Converter. Refresh Button Press “Refresh” button to refresh current status.
User’s Manual of IGT-90x 4.7.4 802.3ah Setup When enable 802.3ah OAM function, all 802.3ah OAMPDU packets will trap to embedded CPU. Software will implement auto discovery procedure. With hardware support, software controls the 802.3ah remote loop back procedure. Hardware can also detect dying gasp even and interrupt CPU to send dying gasp even notification OAMPDU. All other functions defined by 802.3ah are implemented using embedded CPU.
User’s Manual of IGT-90x 4.7.5 802.3ah Loop Back Test The 802.3ah Loop Back Test allows manual run this loop back test to check the interconnection between two Industrial Media Converter devices. To assure the Remote 802.3ah function can work correctly. This function provides 802.3ah Loop Back Test of Industrial Managed Media Converter. Press the “Apply” button to run 802.3ah Loop Back Test and see the 802.
User’s Manual of IGT-90x The 802.3ah Loop Back Test Web page includes the following configurable data: 802.3ah Loop Back Test Send Packet Number Allow input the number for packet send and the available options is 1 to 255. Default is 16. Packet Length (Not include CRC) Allow input the number for Packet Length and the available options is 60 to 1514. Default is 60. Apply Button Press this button for save current configuration of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.8 Security This function provides TCP / UDP Filter setting of Industrial Managed Media Converter. Press the “Apply” button to save the current configuration of Industrial Managed Media Converter. The screen in Figure 4-40 appears and Table 4-17 describes the TCP / UDP Filter setting object of Industrial Managed Media Converter.
User’s Manual of IGT-90x 4.9 Logout This function provides Logout function of Industrial Managed Media Converter, when the “Are you sure to logout” pop window appears; press the “OK” button to logout Web page of Industrial Managed Media Converter. The screen in Figure 4-41 & 4-42 appears.
User’s Manual of IGT-90x 5. TROUBLE SHOOTING This chapter contains information to help you solve problems. If the media converter is not functioning properly, make sure the media converter was set up according to instructions in this manual. The Link LED is not lit Solution: 1. Check the cable connection and remove duplex mode of the Industrial Managed Media Converter. 2. Check the port configuration of the link partner; make sure the two side devices with the same link configuration.
User’s Manual of IGT-90x APPENDIX A NETWORKING CONNECTION A.
User’s Manual of IGT-90x There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : Industrial Managed Gigabit Ethernet Media Converter : IGT-902, IGT-902S, IGT-905A, IGT-902T, IGT-902TS * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
