Industrial 1-/2-Port 10/100/1000T + 1-/2-Port 100/1000/2500X SFP Managed Media Converter IGT-900-Series Quick Installation Guide
Table of Contents 1. Package Contents....................................................................... 3 2. Requirements............................................................................. 4 3. Wiring the Power Inputs............................................................. 5 3.1 Grounding the Device........................................................... 6 4. Starting Web Management.......................................................... 7 4.1 Logging in to the Media Converter.....
1. Package Contents Thank you for purchasing PLANET Industrial Managed Media Converter, IGT-900-Series. The models are as follows: Model Port RJ45 Ports SFP Ports IGT-900-1T1S 1 1 IGT-900-2T2S 2 2 “Media Converter” mentioned in this Quick Installation Guide refers to the above two models. Open the box of the Media Converter and carefully unpack it.
2. Requirements The Media Converter provides remote login interface for management purposes. The following equipment is necessary for further management: zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/ IP Protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Ethernet Port Connection Network cables -- Use standard network (UTP) cables with RJ45 connectors.
3. Wiring the Power Inputs The Upper Panel of the Media Converter comes with one 6-contact terminal block. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5 and 6 for Power 2. IGT-900-1T1S and IGT-900-2T2S: DC 9-48V, AC 24V Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 V1+ PWR1 V2+ Alarm PWR2 DC Input: 9-48V , 1A max. AC Input: 24V , 0.6A max. Figure 3-1: IGT-900-1T1S/IGT-900-2T2S Upper Panel 2.
1.The wire gauge for the terminal block should be in the range from 12 to 24 AWG. Note 2.Please check the wire AWG Ampere specification before connecting Media Converter. 3.1 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 V1+ PWR1 6 V2+ Alarm PWR2 DC Input: 9-48V , 1A max. AC Input: 24V , 0.6A max.
4. Starting Web Management The following shows how to start up the Web Management of the Media Converter. Note the Media Converter is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Media Converter is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Figure 4-2: Login Screen 3. After entering the password, the main screen appears as shown in Figure 4-3. Figure 4-3: Web Main Screen of Industrial Managed Media Converter The Industrial Managed Media Converter Menu on the top and left of the Web page lets you access all the functions and status the Industrial Managed Media Converter provides.
more buttons, such as “System”, “Switching”, “QoS”, “Security”, “Ring” and “Maintenance”. Figure 4-4: Menu Now, you can use the Web management interface to continue the Media Converter management. Please refer to the user manual for more. Note If you are not familiar with Switching functions or the related parameter, press the “Help icon” anytime on the Web page to get the help description.
4.2 Saving Configuration via Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Menu bar. Figure 4-5: Save Config -- Hot Key 2. Press the “Save Configuration” button. 3. Or the other way to save the setting is to Click Maintenance, Save Startup Config.
5. Recovering Back to Default Configuration To reset the IP address to the default IP address “192.168.0.100” and the user password to factory default mode (default password is admin), press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can log in the management Web interface within the same subnet of 192.168.0.xx and default password. Be noted that all the previous setups will be disappeared after the factory default reset is made.
6. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET technical support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq Technical support team mail address: support@planet.com.tw IGT-900-Series User’s Manual: https://www.planet.com.
