User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET industrial Gigabit Media Converter,
IGT-805AT. In the following sections, the term “Industrial Gigabit
Media Converter” mentioned in this user’s manual also means the
IGT-805AT.
Open the box of the Industrial Gigabit Media Converter and
carefully unpack it. The box should contain the following items:
Industrial Gigabit
Media Converter x 1
User's Manual x 1
Wall-mount Plate w/
Screws x 1
DIN-rail Bracket
w/Screws x 1
RJ45 Dust Cap x 1 SFP Dust Cap x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Weight 395g
Power Requirements
DC 12~48V, redundant power with reverse
polarity protection function.
AC 24V power adapter
Power
Consumption/
Dissipation
2.6 watts/8.8BTU (DC 48V)
Converter Specications
Flow Control
Back pressure for half duplex.
IEEE 802.3x pause frame for full duplex
Fabric 4Gbps
Throughput
(packet per second)
2.97Mpps@64bytes
Maximum
Transmission Unit
9216 bytes
Network Cables
10/100/1000BASE-T:
Cat3, 4, 5, 5e, 6 UTP cable
(100 meters, max.)
EIA/TIA-568 100-ohm STP
(100 meters, max.)
1000BASE-SX:
50/125μm or 62.5/125μm multi-mode
ber optic cable, up to 550m
(varying on SFP module)
1000BASE-LX:
9/125μm single-mode ber optic cable,
up to 10/20/40/60/80/120 kilometers
(varying on SFP module)
3.2 LED Indicators
 System
LED Color Function
P1 Green Lit: indicates power 1 has power.
P2 Green Lit: indicates power 2 has power.
Alarm Red
Lit: indicates either power 1 or power 2 has no
power.
 Per 100/1000BASE-X SFP Port
LED Color Function
LNK/
ACT
Green
Lit: indicates the link through that port is
successfully established at 100Mbps or 1000Mbps.
Blinking: indicates that the Converter is actively
sending or receiving data over that port.
 Per 10/100/1000BASE-T Port
LED Color Function
LNK/
ACT
Green
Lit: indicates that the Gigabit Ethernet Port
is successfully connecting to the network at
10/100/1000Mbps.
Blinking: indicates that the Gigabit Ethernet Port
is actively sending or receiving data over that port.
1000
LNK/
ACT
Green
Lit: indicates the link through that port is
successfully established at 1000Mbps.
Blinking: indicates that the Gigabit Ethernet Port
is actively sending or receiving data over that port.
O: indicates the link through that port is
successfully established at 10/100Mbps.
3. Hardware Introduction
3.1 Three-View Diagram
The three-view diagram of the Industrial Gigabit Media Converter
consists of Ethernet interfaces and one removable 6-pin terminal
block. The LED indicators are also located on the front panel.
 IGT-805AT:
32.00
135.00
87.80
97.10
48.8046.50 39.70
28.00
48.80
53.50 53.50
18.00
15.20
30.00
9.20
40.00
28.0018.00
28.00
18.0028.00
28.00
40.00
163.00
Top View
Side View Front View
Mounting Kit Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Bottom View
P1 P2
LNK/
ACT
LNK/
ACT
1000
Alarm
IGT-805AT
100/1000X
10/100/1000T
Max. Fault Ala rm Loading: 24V, 1A
DC Input: 12-48V
, 1A max.
AC Input: 24V
, 0.6A max.
V1+
V2+
PWR1
PWR2Alarm
2.ProductSpecications
Model IGT-805AT
Hardware Specications
Copper Interface
1 x 10/100/1000BASE-T RJ45 TP
Auto-MDI/MDI-X, auto-negotiation
Fiber Optic
Interface
1 1000BASE-SX/LX/BX SFP interface.
Compatible with 100BASE-FX SFP
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1, Pin 3/4 for fault alarm,
Pin 5/6 for Power 2
Alarm
Provides one relay output for power failure
Alarm relay current carry ability: 1A @ DC
24V
LED
3 x LED for System and Power:
 Green: DC Power 1
 Green: DC Power 2
 Red: Power Alarm
2 x LED for Per Copper Port:
 Green: LNK/ACT
 Green:1000 LNK/ACT
1 x LED for Per SFP Interface
 Green: LNK/ACT
ESD Protection 6KV DC
Enclosure IP30 type metal case
Installation DIN rail kit and wall mount ear
Dimensions
(W x D x H)
32 x 87 x 135 mm
Network Cables
100BASE-FX:
50/125μm or 62.5/125μm multi-mode
ber optic cable, up to 2 kilometers
(varying on SFP module)
9/125μm single-mode ber optic cable, up
to 20/40/60 kilometers
(varying on SFP module)
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet
IEEE 802.3x full-duplex ow control
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
 Front Panel
P1 P2
LNK/
ACT
LNK/
ACT
1000
Alarm
IGT-805AT
100/1000X
10/100/1000T
SFP Port
100/1000BASE-X SFP port
for transceiver module,
enabling to have a networking
distance of 550 meters to 2km
(multi-mode ber) and up to
10/20/40/60/80/120 kilometers
(single-mode ber or WDM
ber).
Gigabit TP Interface
10/100/1000BASE-T
copper RJ45 twisted-pair
with up to 100 meters in
distance.
Figure 2: IGT-805AT Front Panel
3.3 Wiring the Power Inputs
The terminal block connector on the top panel of Industrial Gigabit
Media Converter is used for 12~48V DC power inputs. Please follow
the steps below to insert the power wire.
Caution
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.
1. Insert positive/negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 12-48V
, 1A max.
AC Input: 24V
, 0.6A max.
V1+ V2+
PWR1
PWR2Alarm
1 2 3 4 5 6
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4 5 6
Power 1 Alarm Power 2
+ - + -