Industrial 10/100/1000BASE-T to 100/1000BASE-X SFP Media Converter IGT-805AT Industrial 10/100/1000BASE-T to 2 100/1000BASE-X SFP Media Converter IGT-1205AT User's Manual
Trademarks Copyright © PLANET Technology Corp. 2015. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Contents 1. Introduction............................................................................... 6 1.1 Package Contents................................................................ 6 1.2 Product Overview................................................................. 6 1.3 Product Features.................................................................. 7 1.4 Product Specifications.......................................................... 9 2. Hardware Description......................
. Troubleshooting.........................................................................29 6. Cable Connection Parameters.....................................................30 Appendix A: Approved Planet SFP Transceivers..................................31 Appendix B: Networking Connection.................................................33 B.1 Converter’s RJ45 Pin Assignments.........................................33 B.2 RJ45 Cable Pin Assignments.................................................
1. Introduction 1.1 Package Contents The term “Industrial Gigabit Media Converter” mentioned in this user’s manual also means the IGT-805AT / IGT-1205AT.
Environmentally Hardened Design With IP30 industrial metal case, the Industrial Gigabit Media Converter provides a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curbside traffic control cabinets. It also possesses an integrated power supply source with a wide range of voltages (12 to 48V DC or 24V AC) for worldwide high availability applications requiring dual or backup power inputs.
IGT-1205AT Physical Port 1-port 10/100/1000BASE-T RJ45 with auto MDI / MDI-X function 2 SFP interfaces, 100/1000BASE-X dual mode (DIP switch control) Layer 2 Features IEEE 802.3 / 802.3u / 802.3ab / 802.3z Ethernet standard compliant Supports auto-negotiation and 10/100Mbps half / full duplex and 1000Mbps full duplex mode Prevents packet loss with back pressure (hjalf-duplex) and IEEE 802.
1.4 Product Specifications Model IGT-805AT IGT-1205AT Hardware Specifications Copper Interface Fiber Optic Interfaces 1 x 10/100/1000BASE-T 1 x 10/100/1000BASE-T RJ45 RJ45 1 x 1000BASE-SX/LX/ BX SFP interface.
Converter Specifications Processing Scheme Store-and-Forward Fabric Throughput (packet per second) 4Gbps 6Gbps 2.97Mpps 4.46Mpps Back pressure for half duplex. IEEE 802.3x pause frame for full duplex Flow Control Maximum Transmission Unit 9216bytes Standards Conformance Standards Compliance IEEE IEEE IEEE IEEE IEEE 802.3 Ethernet 802.3u Fast Ethernet 802.3ab Gigabit Ethernet 802.3z Gigabit Ethernet 802.
Bottom View 10/100/1000T 100/1000X P2 FAULT IGT-805AT 1000 LNK/ACT LNK/ACT P1 Top View Rear View Mounting Kit DIN-Rail Kit Mounting Kit 2. Hardware Description 2.
Mounting Kit DIN-Rail Kit Rear View Mounting Kit IGT-1205AT dimensions (W x D x H): 32 x 87 x 135mm V1+ V2PWR2 V2+ 1 2 3 Mode ON Port 1 Port 2 Input DC 12~48V, AC 24V 1 2 3 4 5 6 V1PWR1 Fault ON 100FX Top View Side View OFF 1000X 100FX 1000X Redundant Switch IGT-1205AT 100 1000 LNK/ACT LNK/ACT 3 LNK / ACT SFP 1000X 10/100/1000T 2 1 SFP Bottom View 12 LNK / ACT 1000X P1 P2 FAULT Front View
2.2 Converter Front Panel Figures 2-1 and 2-2 show the front panels of the Industrial Gigabit Media Converter.
2.3 LED Indicators System LED Color Function P1 Green Lit: indicates power 1 has power. P2 Green Lit: indicates power 2 has power. FAULT Green Lit: indicates either power 1 or power 2 has no power. Per 10/100/1000BASE-T Port (IGT-805AT) LED Color Function Lit: indicates that the Gigabit Ethernet Port is successfully connecting to the network at 10/100/1000Mbps. LNK/ACT Green Blinking: indicates that the Gigabit Ethernet Port is actively sending or receiving data over that port.
Per 10/100/1000BASE-T Port (IGT-1205AT) LED Color Function Lit: indicates the link through that port is successfully established at 100Mbps or 10Mbps. 100 Orange LNK/ACT Blinking: indicate that the Switch is actively sending or receiving data over that port. Off: indicates the link through that port is successfully established at 1000Mbps. Lit: indicates the link through that port is successfully established at 1000Mbps.
2.4 Converter Upper Panel The upper panel of the IGT-805AT and IGT-1205AT consist of one terminal block connector within two DC power inputs, and the IGT-1205AT also provides 3 DIP Switches for 100/1000X fiber support on two SFP slots and fiber redundant function.
3. INSTALLATION This section describes the functionalities of the Industrial Gigabit Media Converter’s components and guides you to how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 3.1 Quick Installation Steps Step 1: Unpack the Industrial Gigabit Media Converter. Step 2: Check whether the DIN-rail is screwed on the Industrial Gigabit Media Converter.
3.2 Mounting Installation This section describes how to install the Industrial Gigabit Media Converter and makes connections to it. Please read the following topics and perform the procedures in the order being presented. Note In the installation steps below, this Manual uses IGS-801 (PLANET 8-port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Switch and Industrial Media Converter are similar. 3.2.
1 2 Step 2: Lightly insert the DIN-rail into the track. Step 3: Make sure the DIN-rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial Gigabit Media Converter from the track.
Step 5: Lightly pull out the bottom of the DIN-Rail from the track to remove. 3.2.2 Wall-mount Plate Mounting To install the Industrial Gigabit Media Converter on the wall, please follow the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Gigabit Media Converter; loosen the screws to remove the DIN-rail. Step 2: Place the wall-mount plate on the rear panel of the Industrial Gigabit Media Converter.
3.3 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Gigabit Media Converter is used for two DC redundant power inputs. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2.
Note The wire gauge for the terminal block should be in the range between 12 and 24 AWG. 3.4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. When inserting the wires, the Industrial Gigabit Media Converter will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
3.5 Cable Connection Installing the SFP Transceiver The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Industrial Gigabit Media Converter as Figure 3-1 shows MGB / MFB Series Transceiver Figure 3-1: Plug in the SFP Transceiver Note It is recommended to use PLANET SFPs on the Industrial Gigabit Media Converter.
2. Make sure both sides of the SFP transceiver are with the same media type; for example, 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to 1000BASE-LX. 3. Check whether the fiber-optic cable type matches the SFP transceiver model. To connect to 1000BASE-SX SFP transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type. To connect to 1000BASE-LX SFP transceiver, use the single-mode fiber cable with one side being the male duplex LC connector type.
Connecting the fiber cable 1. Attach the duplex LC connector on the network cable to the SFP transceiver. 2. Connect the other end of the cable to a device, switches with SFP installed, to fiber NIC on a workstation or a Media Converter. 3. Check the LNK/ACT LED of the SFP slot of the switch / converter. Make sure that the SFP transceiver is operating correctly. Removing the Transceiver Module 1. Make sure there is no network activity by consulting or checking with the network administrator.
10/100/1000BASE-T The 10/100/1000BASE-T port comes with auto-negotiation capability. It automatically supports 1000BASE-T, 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into the 10/100/1000BASE-T port, and then turn on the Industrial Gigabit Media Converter. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation with the connected device.
3.6 Redundancy Overview (IGT-1205AT only) The IGT-1205AT provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant-mode supports autorecover function. If the destination port of a packet is link down, it will forward the packet to the other port of the backup pair. The following figure shows the redundant function.
4. Applications In this paragraph, we will describe how to install the Industrial Gigabit Media Converter.
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Gigabit Media Converter is not functioning properly, make sure the Industrial Gigabit Media Converter is set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Gigabit Media Converter. Performance is bad Solution: Check the speed duplex mode of the partner device.
6. Cable Connection Parameters The wiring details are shown below: 100FX Fiber Optic Cables: Standard Fiber Type Cable Specifications 100BASE-FX (1300nm) Multi-mode 50/125μm or 62.5/125μm Multi-mode 50/125μm or 62.5/125μm Single-mode 9/125μm Single-mode 9/125μm 100BASE-FX (1310nm) 100BASE-BX-U (TX :1310/RX :1550) 100BASE-BX-D (TX :1550/RX :1310) 1000X Fiber Optic Cables: Standard Fiber Type Cable Specifications 1000BASE-SX (850nm) Multi-mode 50/125μm or 62.
Appendix A: Approved Planet SFP Transceivers PLANET Industrial Gigabit Media Converter supports 100/1000 dual mode with both single mode and multi-mode SFP transceivers.
MGB-TLX SFP-Port 1000BASE-LX mini-GBIC module - 10km (-40~75°C) MGB-TL30 SFP-Port 1000BASE-LX mini-GBIC module - 30km (-40~75°C) MGB-TL70 SFP-Port 1000BASE-LX mini-GBIC module - 70km (-40~75°C) Fast Ethernet SFP Transceiver Modules MFB-FX SFP-Port 100BASE-FX Transceiver (1310nm) - 2km MFB-F20 SFP-Port 100BASE-FX Transceiver (1310nm) - 20km MFB-F40 SFP-Port 100BASE-FX Transceiver (1310nm) - 40km MFB-F60 SFP-Port 100BASE-FX Transceiver (1310nm) - 60km MFB-FA20 SFP-Port 100BASE-BX Transceiver (W
Appendix B: Networking Connection B.
B.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product : Industrial 10/100/1000BASE-T to 2 100/1000BASE-X SFP Media Converter (-40~75 degrees C) : IGT-1205AT *Model Number * Produced by: Manufacturer Name Manufacturer Address : Planet Technology Corp. : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
EC Declaration of Conformity For the following equipment: *Type of Product: *Model Number: Industrial 10/100/1000BASE-T to 100/1000BASE-X SFP Media Converter (-40~75 degrees C) IGT-805AT * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
