User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.1 DIN-rail Mounting Installation
1
2
3.2 Wall-mount Plate Mounting
3.3 Side Wall-mount Plate Mounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
3.3 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP
port.
The SFP transceivers are hot-pluggable and hot-swappable. You can
plug in and out the transceiver to/from any SFP port without having
to power down the Industrial Gigabit Media Converter as Figure 3-1
shows.
MGB / MFB
Series Module
Figure 3-1: Inserting the SFP Transceiver
Note
It is recommended to use PLANET SFP transceiver on
the Industrial Gigabit Media Converter. If you insert an
SFP transceiver that is not supported, the Industrial
Gigabit Media Converter will not recognize it.
4. Product Specications
Model IGT-1205AT IGT-2205AT
Hardware Specications
Copper Interface
1 x 10/100/1000BASE-T
RJ45
2 x 10/100/1000BASE-T
RJ45
Fiber Optic
Interfaces
2 x 100/1G/2.5GBASE-X SFP interfaces
(Port-1 and Port-2)
Supports auto detection
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1;
Pin 3/4 for fault alarm;
Pin 5/6 for Power 2
DIP Switch
DIP Position Function
Fiber
Mode
ON Fiber Redundancy
OFF (default) Switch Mode
Alarm
Provides one relay output for power failure
Alarm Relay current carry ability: 1A @ DC 24V
Power
Requirements
DC 12~48V or AC 24V
Redundant power with reverse polarity protection
Power
Consumption /
Dissipation
4.8 watts/16BTU 4.92 watts/16.9BTU
Dimensions
(W x D x H)
32 x 87 x 135mm 32 x 87 x 135mm
Weight 412g 419g
Enclosure IP30 type metal case
Installation DIN-rail kit and wall mount ear
ESD Protection 6KV DC
Converter Specications
Processing
Scheme
Store-and-Forward
Fabric 12Gbps 14Gbps
Throughput
(packet per
second)
8.93Mpps@64bytes 10.42Mpps@64bytes
Flow Control
Back pressure for half duplex.
IEEE 802.3x pause frame for full duplex
Address Table 4K entries
Jumbo Frame 9216bytes
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.1p Class of Service
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
PLANET Industrial Gigabit Media Converter supports 100/1000/2500X
with both single mode and multi-mode SFP transceivers. Before we
connect Industrial Gigabit Media Converter to the other network device,
please do the following:
1. Set the DIP Switch of SFP Port 1 or Port 2 to the “OFF” position
with ber speed auto detection.
DIP Position Function
Fiber Mode
ON Fiber Redundancy
OFF (default) Switch Mode
2. Make sure both sides of the SFP transceivers are with the same
media type, for example, 1000BASE-SX to 1000BASE-SX, and
1000BASE-LX to 1000BASE-LX.
Note
Never pull out the module without pulling the lever or
the push bolts on the module. Directly pulling out the
module with force could damage the module and the
SFP port of the Industrial Gigabit Media Converter.
5. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.