User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 ARP
- 4.2.1.5 Users Configuration
- 4.2.1.6 Privilege Levels
- 4.2.1.7 NTP Configuration
- 4.2.1.7.1 System Time Correction Manually
- 4.2.1.8 Time Configuration
- 4.2.1.9 UPnP
- 4.2.1.10 DHCP Relay
- 4.2.1.11 DHCP Relay Statistics
- 4.2.1.12 CPU Load
- 4.2.1.13 System Log
- 4.2.1.14 Detailed Log
- 4.2.1.15 Remote Syslog
- 4.2.1.16 SMTP Configuration
- 4.2.1.17 Fault Alarm
- 4.2.1.18 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 VLAN Translation
- 4.3.5 Spanning Tree Protocol
- 4.3.6 Multicast
- 4.3.7 MLD Snooping
- 4.3.8 MVR (Multicast VLAN Registration)
- 4.3.9 LLDP
- 4.3.10 MAC Address Table
- 4.3.11 Loop Protection
- 4.3.12 UDLD
- 4.3.13 GVRP
- 4.3.14 PTP
- 4.3.15 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-5225-16T4S/IGSW-24040T
20
1.5 Product Specifications
Product
IGS-5225-16T4S IGSW-24040T
Hardware Specifications
Hardware Version
2
3
10/100/1000T Copper Ports
16 24
100/1000X SFP Slots
4, port 17 to port 20 4, shared with Port-21 to Port-24
Console
1 x RS232-to-RJ45 serial port (115200, 8, N, 1)
SDRAM
128Mbytes
Flash Memory
64Mbytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm
One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
DI/DO
2 Digital Input (DI):
Level 0: -24~2.1V
Level 1: 2.1~24V
Max. input current: 10mA
2 Digital Output (DO): Open collector to 24VDC, 100mA
Dimensions (W x D x H)
444 x 200 x 44.2 mm, 1U height
Weight
2672g
2788g
Power Consumption
Max. 15.2 watts/51.8 BTU Max. 19.7 watts/67.2 BTU
Power Requirements – AC
AC 100~240V, 50/60Hz 0.4A AC 100~240V, 50/60Hz 0.5A
Power Requirements – DC
DC 36~60V, 0.6A DC 36~60V, 0.7A
EFT Protection
6KV DC
ESD Protection
6KV DC
LED
System:
AC (
Green), DC1 (Green), DC2 (Green),
Alarm (
Red), Ring (Green), R.O. (Green),
DI/DO (
Red)
10/100/1000T RJ45 Interfaces
(
Port 1 to Port 16):
1000Mbps LNK/ACT (
Green)
10/100Mbps LNK/ACT (
Amber)
100/1000Mbps SFP Combo Interfaces
(
Port 17 to Port 20):
1000Mbps LNK/ACT (
Green)
100Mbps LNK/ACT (Amber)
System:
AC (Green), DC1 (Green), DC2 (Green),
Alarm (Red), Ring (Green), R.O. (Green
),
DI/DO (Red)
10/100/1000T RJ45 Interfaces
(Port 1 to Port 24):
1000Mbps LNK/ACT (Green)
10/100Mbps LNK/ACT (Amber)
100/1000Mbps SFP Combo Interfaces
(Port 21 to Port 24):
1000Mbps LNK/ACT (Green)
100Mbps LNK/ACT (Amber)
Switching Specifications
Switch Architecture
Store-and-Forward
Switch Fabric
40Gbps/non-blocking 48Gbps/non-blocking
Throughput
29.76Mpps@64Bytes 35.71Mpps@64Bytes
Address Table
8K entries, automatic source address learning and aging
Shared Data Buffer
4M bits
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex