User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET IGS-824UPT Industrial 8-Port
Gigabit Ethernet Switch with 4-Port PoE++. The interfaces of
this model are shown below:
Model Name
10/100/1000T
RJ45 Port
100/1000X
SFP Slot
PoE Port
IGS-824UPT 6 2 4
Open the box of the Industrial PoE++ Switch and carefully
unpack it. The box should contain the following items:
Industrial PoE++
Switch x 1
User’s Manual x 1 Wall-mount Kit x 1
DIN-rail Kit x 1 RJ45 Dust Cap x 6 SFP Dust Cap x 2
If any of these are missing or damaged, please contact your
dealer immediately.
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
Switch Specications
Switch Architecture Store-and-Forward
Switch Fabric 16Gbps
Throughput
(packet per second)
11.9Mpps@64bytes
Address Table 4K entries
Buer Memory 1M bits on-chip buer memory
Jumbo Frame 9Kbytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Power over Ethernet
PoE Standard
IEEE 802.3bt PoE++ type 4 PSE
Backward compatible with IEEE 802.3at
PoE+ PSE
PoE Power Supply
Type
802.3bt/PoH
End-span/Mid-span
PoE Power Output
Max. 90 watts to 802.3bt PoE++ PD
Max. 95 watts to PoH PD
Max. 36 watts to 802.3at PoE+ PD
Power Pin
Assignment
End-span: 1/2(-), 3/6(+)
Mid-span: 4/5(+), 7/8(-)
802.3bt/PoH: 1/2(-), 3/6(+), 4/5(+),
7/8(-)
PoE Power Budget
240 watts maximum@52-54V DC input
160 watts maximum@48-51V DC input
 Per 802.3bt PoE++ 10/100/1000BASE-T Interface
(Port 1 to Port 4)
LED Color Function
LNK/ACT Green
Lights to indicate the link through that
port is successfully established at 10Mbps
or 100Mbps or 1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
PoE-in-
Use
Amber
Lights to indicate the port is providing DC
in-line power.
O to indicate the connected device is not
a PoE powered device (PD).
 Per 10/100/1000BASE-T Interface (Port 5 and Port 6)
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the port is successfully
established at 1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
10/100
LNK/ACT
Amber
Lights to indicate the port is successfully
established at 100Mbps or 10Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
3. Hardware Introduction
3.1 Switch Front Panel
4
2
3
65
1
IGS-824UPT
802.3bt PoE++
P1
P2 Fault
80W 160W 240W
PoE
Usage
ACTLNK
PoE-in-Use
1000 LNK/ACT
10/100 LNK/ACT
7
8
7
8
1
2
3
1. Gigabit Ethernet PoE++
Interfaces
802.3bt PoE++
10/100/1000BASE-T copper,
RJ45 twisted-pair: Up to 100
meters.
2. Gigabit Ethernet TP
Interfaces
10/100/1000BASE-T copper,
RJ45 twisted-pair: Up to 100
meters.
3. 100/1000BASE-X SFP Slot
The SFP slots built in the IGS-
824UPT supports SFP auto-
detection and dual speed as
it features 1000BASE-SX/
LX/BX and 100BASE-FX SFP
(small form-factor pluggable)
fiber-optic modules.
The distance can be extended
from 550 meters to 2
kilometers (multi-mode fiber)
and 10/20/40/60/80/120
kilometers (single-mode fiber
or WDM fiber).
Figure 1: IGS-824UPT
Front View
2. Product Features
Model IGS-824UPT
Hardware Specications
Copper Ports
6 10/100/1000BASET RJ45 auto-MDI/
MDI-X ports
SFP Slots
2 1000BASE-SX/LX/BX SFP interfaces
Compatible with 100BASE-FX SFP
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1
Pin 3/4 for fault alarm
Pin 5/6 for Power 2
Alarm
One relay output for power failure.
Alarm relay current carry ability: 1A@
DC 24V
Power Requirements
48~54V DC, 5A (max.)
Redundant power with reverse polarity
protection function
Power Consumption
Max. 2.24 watts/7.64BTU (System on)
Max. 5.2 watts/17.74BTU
(Ethernet Full Loading)
Max. 252 watts/860BTU
(Ethernet + PoE Full Loading)
Dimensions
(W x D x H)
55 x 85 x 135 mm
Weight 777g
Enclosure IP30 aluminum case
Standard Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3az Gigabit SX/LX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Ecient Ethernet
(EEE)
IEEE 802.3bt Power over Ethernet Plus
Plus
IEEE 802.3at Power over Ethernet Plus
PSE
IEEE 802.1p Class of Service
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
3.2 LED Indicators
 System
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
FAULT Red
Lights to indicate either power 1 or power
2 has no power.
 PoE Power Usage (Unit: Watt)
LED Color Function
80W Amber
Blinks to indicate that the PoE usage is
around 40W to 79W.
Lights to indicate the PoE usage is around/
over 80W.
160W Amber
Blinks to indicate that the PoE usage is
around 120W to 159W.
Lights to indicate the PoE usage is around/
over 160W.
240W Amber
Blinks to indicate that the PoE usage is
around 200W to 239W.
Lights to indicate the PoE usage is at the
maximum.
 Per 1000BASE-X SFP Slot (Port 7 and Port 8)
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the port is successfully
established at 1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
100
LNK/ACT
Amber
Lights to indicate the port is successfully
established at 100Mbps
Blinks to indicate that the Switch is
actively sending or receiving data over
that port.
3.3 Switch Upper Panel
The upper panel of the Industrial PoE++ Switch consists of one
terminal block connector within two DC power inputs.
Figure 3-2 shows the upper panel of the Industrial PoE++
Switch.
DC Input:
48-54V , 5A max.
PWR1
PWR2
Fault
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 3-2: Industrial PoE++ Switch Upper Panel