5-/8-Port 10/100/1000Mbps Industrial Gigabit Ethernet Switch IGS-501T / IGS-801T User's Manual
Trademarks Copyright © PLANET Technology Corp. 2014. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Contents 1. INTRODUCTION......................................................................... 5 1.1 Package Contents................................................................ 5 1.2 How to Use This Manual....................................................... 5 1.3 Product Features.................................................................. 6 1.4 Product Specifications.......................................................... 7 2. INSTALLATION.........................................
1. INTRODUCTION 1.1 Package Contents Check the contents of your package for the following parts: zz Industrial Gigabit Ethernet Switch x 1 zz User’s Manual x 1 zz DIN Rail Kit x 1 zz Wall Mount Kit x 1 If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 1.
1.3 Product Features Physical Port zz 5-Port 10/100/1000Base-T RJ-45 with auto MDI/MDI-X function (IGS-501T) zz 8-Port 10/100/1000Base-T RJ-45 with auto MDI/MDI-X function (IGS-801T) Layer 2 Features zz Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.
1.4 Product Specifications Model IGS-501T IGS-801T 5 8 Hardware Specifications 10/100/1000Base-T Ports Dimensions (W x D x H) Weight Power Requirements Power Consumption / Dissipation Installation 135mm x 87mm x 32mm 498g 498g 12~48V DC, redundant power with polarity reverse protection function, 24V AC power support 11.2 watts / 38.2BTU 5.
Standards Compliance IEEE IEEE IEEE IEEE Temperature Operating: -40~75 degrees C Storage: -40~75 degrees C Humidity Operating: 5% to 95%, Storage: 5% to 95% (non-condensing) Regulation Compliance FCC Part 15 Class A, CE 8 802.3 Ethernet 802.3u Fast Ethernet 802.3ab Gigabit Ethernet 802.
2. INSTALLATION This section describes the functionalities of the Industrial Gigabit Ethernet Switch’s components and guides how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. In the following section, the term “Industrial Gigabit Ethernet Switch” means the IGT-501T / IGT-801T. 2.
2.1.1 Product Overview PLANET Industrial Gigabit Ethernet Switch comes with 5/8 RJ-45 10/100/1000Mbps ports for high-speed network connectivity. The Industrial Gigabit Ethernet Switch can also automatically identify and determine the correct transmission speed and half / full duplex mode of the attached devices with its 5/8 ports. The Gigabit port with 9K jumbo frame feature supported can handle extremely large amounts of data transmission in a secure topology linking to a backbone or highpower servers.
2.1.3 LED Indicators LED Color Function P1 Green Lit: indicates power 1 has power. P2 Green Lit: indicates power 2 has power. FAULT Green Lit: indicates either power 1 or power 2 has no power. 1000 Green Lit: indicates the Switch is successfully connecting to the network at 1000Mbps. Off: indicates that the Switch is successfully connecting to the network at 10Mbps or 100Mbps. Blink: indicatse that the Switch is actively sending or receiving data over that port.
2.1.5 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Gigabit Ethernet Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. DC12~48V, AC 24V V1- V1 + V2 - V2 + 2. Tighten the wire-clamp screws for preventing the wires from loosening.
2.1.6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Gigabit Ethernet Switch will detect the fault status of the power failure, or port link failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts. Insert the wires into the fault alarm contacts Note 1.
2.2.1 DIN-Rail Mounting The DIN-Rail is screwed on the Industrial Gigabit Ethernet Switch when out of factory. When you need to replace the wall mount application with DIN-Rail application on Industrial Gigabit Ethernet, please refer to the following figures to screw the DIN-Rail on the Industrial Gigabit Ethernet Switch. To hang the Industrial Gigabit Ethernet Switch, follow the steps below: Step 1: Screw the DIN-Rail on the Industrial Gigabit Ethernet Switch.
Step 3: Check whether the DIN-Rail is tightly on the track. Step 4: Please refer to following procedures to remove the Industrial Gigabit Ethernet Switch from the track. Step 5: Lightly pull out the bottom of DIN-Rail to remove it from the track. 2.2.2 Wall Mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall, please follow the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Gigabit Ethernet Switch; loose the screws to remove the DIN-Rail.
Step 3: Use the screws to screw the wall mount plate on the Industrial Gigabit Ethernet Switch. Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Gigabit Ethernet Switch on the wall. Step 5: To remove the wall mount plate, reverse the steps above.
3. APPLICATIONS In this paragraph, we will describe how to install Industrial Gigabit Ethernet Switch and the installation points for the attention.
Step 3: To hang the Industrial Gigabit Ethernet Switch on the DIN-Rail track or wall, please refer to the Mounting Installation section. Step 4: Power on the Industrial Gigabit Ethernet Switch. (Please refer to the Wiring the Power Inputs section for power input.) The power LED on the Industrial Gigabit Ethernet Switch will light up. Please refer to the LED Indicators section for the definition of LED lights. Step 5: Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.
4. SWITCH OPERATION 4.1 Address Table The Industrial Gigabit Ethernet Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some nodes in the network, including MAC address, port no, etc. This information comes from the learning process of Industrial Gigabit Ethernet Switch. 4.
4.4 Store-and-Forward Store-and-Forward is one type of packet-forwarding techniques. A Store-and Forward Industrial Gigabit Ethernet Switch stores the incoming frame in an internal buffer, do the complete error checking before transmission. Therefore, no error packets occur as it is the best choice when a network needs efficiency and stability.
5. TROUBLESHOOTING This chapter contains information to help you solve issues. If the Industrial Gigabit Ethernet Switch is not functioning properly, make sure the Industrial Gigabit Ethernet Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Gigabit Ethernet Switch. Performance is bad Solution: Check the speed duplex mode of the partner device.
APPENDIX A: NETWORKING CONNECTION A.
A.2 RJ-45 Cable Pin Assignments The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is colorcoded.
EC Declaration of Conformity For the following equipment: *Type of Product : *Model Number : * Produced by: Manufacturer‘s Name Manufacturer‘s Address 5/8-Port 10/100/1000Mbps Industrial Ethernet Switch IGS-501T, IGS-801T : Planet Technology Corp. : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.
