Datasheet

11
IGS-6325-8UP2S2X
IGS-6325-8UP2S
Specications
Product
IGS-6325-8UP2S IGS-6325-8UP2S2X
HardwareSpecications
Copper Ports 8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP Ports
2 1000BASE-SX/LX/BX SFP slot interfaces (Port-9 and Port-10)
Compatible with 100BASE-FX SFP
SFP+ Ports --
2 10GbBASE-SR/LR SFP+ slot
interfaces (Port-11 to Port-12)
PoE Injector Ports 8 ports with 802.3bt PoE++ injector function with Port-1 to Port-8
Console 1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 20Gbps/non-blocking 60Gbps/non-blocking
Throughput (packet per second) 14.8Mpps@ 64 bytes packet 44.64Mpps@ 64 bytes packet
Address Table 16K entries, automatic source address learning and aging
Shared Data Buffer 32Mbits
Jumbo Frame 10Kbytes
SDRAM 512Mbytes
Flash Memory 64Mbytes
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
Digital Input (DI)
2 digital input:
Level 0: -24~2.1V (±0.1V)
Level 1: 2.1~24V (±0.1V)
Input load to 24V DC, 10mA max.
Digital Output (DO)
2 digital output:
Open collector to 24VDC, 100mA
Enclosure IP30 aluminum case
Installation DIN-rail or wall mounting
Dimensions (W x D x H) 76 x 107 x 152 mm
Weight 1,138g 1,152g
Power Requirements
Dual DC 48~56V, 7A max.
(>52V DC for 802.3bt PoE++ output recommended)
Power Consumption
Max. 27 watts/92.13BTU@56V DC input (System on)
Max. 395 watts/1,347.80BTU@56V DC input (Full loading
with 802.3bt PoE++ function)
Max. 29 watts/98.96BTU@56V DC input (System on)
Max. 401 watts/1,368.27BTU@56V DC input (Full loading
with 802.3bt PoE++ function)
ESD Protection 6KV DC
Surge Protection 4KV DC
LED Indicators
System:
Power 1 (Green), Power 2 (Green)
Fault Alarm (Red)
Ring (Green), Ring Owner (Green)
DIDO (Red)
Per 10/100/1000T RJ45 PoE++ Port:
1000Mbps LNK/ACT (Green)
10/100Mbps LNK/ACT (Amber)
802.3bt PoE++-in-use x 1 (Green)
802.3at/af PoE-in-use x 1 (Amber)
Per SFP Interface:
1000 LNK/ACT (Green)
100 LNK/ACT (Amber)
Per SFP+ Port:
10Gbps LNK/ACT (Green)
1Gbps LNK/ACT (Amber)
PoE Usage:
80W, 160W, 240W, 320W (Amber)