User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 4.8 Power over Ethernet
- 4.9 ONVIF
- 4.10 Routing
- 4.10.1 IP Configuration
- 4.10.2 IP Status
- 4.10.3 Routing Information Base
- 4.10.4 OSPF
- 4.10.4.1 Global Configuration
- 4.10.4.2 Network Area
- 4.10.4.3 Passive Interface
- 4.10.4.4 Stub Area
- 4.10.4.5 Area Authentication
- 4.10.4.6 Area Range
- 4.10.4.7 Interface Configuration
- 4.10.4.8 Virtual Link
- 4.10.4.9 Global Status
- 4.10.4.10 Area Status
- 4.10.4.11 Neighbor Status
- 4.10.4.12 Interface Status
- 4.10.4.13 Configuration Example of OSPFv4
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-6325 series
41
System
LED
Color
Function
DC1 Green
Lights to indicate DC power input 1 has power.
DC2 Green
Lights to indicate DC power input 2 has power.
Fault Red
Lights to indicate that Switch DC or port has failed.
Ring Green
Lights to indicate that the ERPS Ring has been created successfully.
R.O. Green
Lights to indicate that Ring state is in idle mode.
Blinks to indicate that the Ring state is in protected mode.
DI/DO Red
Blinks to indicate that Switch DC or port has failed or DI has event.
LED Color Function
10/100 Amber
Lights to indicate that the port is operating at 10/100Mbps.
Blinks to indicate that the switch is actively sending or receiving data over that port.
1000 Green
Lights to indicate that the port is operating at 1000Mbps.
Off to indicate that the switch is actively sending or receiving data over that port.
802.3at PoE Amber
Lights: To indicate the port is providing DC in-line power with 802.3af/at PoE+ mode.
Off to indicate the connected device is not a PoE Powered Device (PD
802.3bt PoE Green
Lights: To indicate the port is providing DC in-line power with 802.3bt PoE++ mode.
Off to indicate the connected device is not a PoE Powered Device (PD
Per SFP Interface
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the port is running at 1000Mbps and successfully established.
Blinks to indicate that the switch is actively sending or receiving data over that port.
100
LNK/ACT
Amber
Lights to indicate the port is running at 100Mbps and successfully established.
Blinks to indicate that the switch is actively sending or receiving data over that port.
Per 1/10G SFP+ Interface (IGS-6325-8UP2S2X)
LED Color Function
1000
LNK/ACT
Green
Lights to indicate the port is running at 1Gbps and successfully established.
Blinks to indicate that the switch is actively sending or receiving data over that port.
10G
LNK / ACT
Amber
Lights to indicate the port is running at 10Gbps and successfully established.
Blinks to indicate that the switch is actively sending or receiving data over that port.