User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 4.8 Power over Ethernet
- 4.9 ONVIF
- 4.10 Routing
- 4.10.1 IP Configuration
- 4.10.2 IP Status
- 4.10.3 Routing Information Base
- 4.10.4 OSPF
- 4.10.4.1 Global Configuration
- 4.10.4.2 Network Area
- 4.10.4.3 Passive Interface
- 4.10.4.4 Stub Area
- 4.10.4.5 Area Authentication
- 4.10.4.6 Area Range
- 4.10.4.7 Interface Configuration
- 4.10.4.8 Virtual Link
- 4.10.4.9 Global Status
- 4.10.4.10 Area Status
- 4.10.4.11 Neighbor Status
- 4.10.4.12 Interface Status
- 4.10.4.13 Configuration Example of OSPFv4
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-6325 series
25
Digital Output 2 Digital Output (DO) Open collector to 24V DC, 100mA max.
Dimensions (W x D x H) 84 x 107 x 152 mm 76 x 107 x 152 mm
Weight
1550g 1138g 1152g
Power Requirements
48~56V DC (>51V DC for
PoE+ output
recommended)
Dual DC 48~56V, 7A max.
(>52V DC for 802.3bt PoE++ output recommended)
Power
Consumption
System on Max. 12.1 watts Max. 27 watts Max. 29 watts
Full loading Max. 350 watts Max. 395 watts Max. 401 watts
Power Over Ethernet
PoE Standard
IEEE 802.3at Power over
Ethernet Plus/PSE
IEEE 802.3bt PoE++ Type-4 /PSE
PoE Power Supply Type End-span
End-span + Mid-span
End-span
Mid-span
Power Pin Assignment 1/2(+), 3/6(-) 1/2(-), 3/6(+), 4/5(+), 7/8(-)
PoE Power
Output
IEEE 802.3af
Per port 48V~51V DC
(depending on the power
supply), max. 15.4 watts
--
IEEE 802.3at
Per port 51V~56V DC
(depending on the power
supply), max. 36 watts
Per port 51V~56V DC (depending on the power
supply), max. 36 watts
IEEE 802.3bt --
Per port 51V~56V DC (depending on the power
supply), max. 95 watts
PoE Power
Budget
48V DC input - 240W maximum --
52~56V DC
input
- Single power input:
240W maximum
- Dual power input: 320W
maximum
- Single power input: 240W maximum
- Dual power input: 360W maximum
Max. number of Class 3 PDs
16 8
Max. number of Class 4 PDs 10 8
Max. number of bt Type-3 PDs -- 6
Max. number of bt Type-4 PDs
-- 4
PoE Management Functions
PoE Extend Mode
--
(next firmware version)
Yes, max. 160 to 200 meters
Active PoE device alive detects Yes
PoE Power Recycle
Yes, daily or predeinded schedule
PoE Schedule
4 schedule profiles
PoE System Management
System PoE Admin control
Total PoE power budget control
Auto power input and PoE budget control
PoE Legacy mode
Over-termperature threshold alarm
PoE usage threshold alarm
PoE Port Management
Port
Enable/Disable/Schedule
Port Enable/Disable/Schedule
PoE mode control