IGS-6325-Series User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 4.8 Power over Ethernet
- 4.9 ONVIF
- 4.10 Routing
- 4.10.1 IP Configuration
- 4.10.2 IP Status
- 4.10.3 Routing Information Base
- 4.10.4 OSPF
- 4.10.4.1 Global Configuration
- 4.10.4.2 Network Area
- 4.10.4.3 Passive Interface
- 4.10.4.4 Stub Area
- 4.10.4.5 Area Authentication
- 4.10.4.6 Area Range
- 4.10.4.7 Interface Configuration
- 4.10.4.8 Virtual Link
- 4.10.4.9 Global Status
- 4.10.4.10 Area Status
- 4.10.4.11 Neighbor Status
- 4.10.4.12 Interface Status
- 4.10.4.13 Configuration Example of OSPFv4
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-6325 series
77
period expires, a configured IPv4 address will be used as IPv4 interface
address. A value of zero disables the fallback mechanism, such that
DHCP will keep retrying until a valid lease is obtained. Legal values are
0 to 4294967295 seconds.
Current
Lease
For DHCP interfaces with an active lease, this column shows the current
interface address, as provided by the DHCP server.
IPv4 Address
The IPv4 address of the interface in dotted decimal notation.
If DHCP is enabled, this field configures the fallback address. The field
may be left blank if IPv4 operation on the interface is not desired - or no
DHCP fallback address is desired.
Mask Length
The IPv4 network mask, in number of bits (prefix length). Valid values
are between 0 and 30 bits for an IPv4 address.
If DHCP is enabled, this field configures the fallback address network
mask. The field may be left blank if IPv4 operation on the interface is not
desired - or no DHCP fallback address is desired.
DHCPv6 Enable
Enable the DHCPv6 client by checking this box. If this option is enabled,
the system will configure the IPv6 address of the interface using the
DHCPv6 protocol.
Rapid
Commit
Enable the DHCPv6 Rapid-Commit option by checking this box. If this
option is enabled, the DHCPv6 client terminates the waiting process as
soon as a Reply message with a Rapid Commit option is received.
This option is only manageable when DHCPv6 client is enabled.
Current
Lease
For DHCPv6 interface with an active lease, this column shows the
interface address provided by the DHCPv6 server.
IPv6 Address
The IPv6 address of the interface. An IPv6 address is in 128-bit records
represented as eight fields of up to four hexadecimal digits with a colon
separating each field (:). For example, fe80::215:c5ff:fe03:4dc7. The
symbol :: is a special syntax that can be used as a shorthand way of
representing multiple 16-bit groups of contiguous zeros; but it can
appear only once.
System accepts the valid IPv6 unicast address only, except
IPv4-Compatible address and IPv4-Mapped address.
The field may be left blank if IPv6 operation on the interface is not
desired.
Mask Length
The IPv6 network mask, in number of bits (prefix length). Valid values
are between 1 and 128 bits for an IPv6 address.
The field may be left blank if IPv6 operation on the interface is not
desired.
• IP Routes Delete
Select this option to delete an existing IP route.
Network
The destination IP network or host address of this route. Valid format is