IGS-6325-Series User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.6 Port Isolation
- 4.3.3.7 VLAN setting example:
- 4.3.3.7.1 Two Separate 802.1Q VLANs
- 4.3.3.7.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.7.3 Port Isolate
- 4.3.3.8 MAC-based VLAN
- 4.3.3.9 IP Subnet-based VLAN Membership Configuration
- 4.3.3.10 Protocol-based VLAN
- 4.3.3.11 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Ring
- 4.7 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-6325 series
40
10Gbps SFP+ (10G Ethernet/10GBASE)
Model
Speed (Mbps)
Connector
Interface
Fiber Mode
Distance
Wavelength (nm)
Operating Temp.
MTB-SR
10G
LC
Multi Mode
Up to 300m
850nm
0 ~ 60 degrees C
MTB-LR
10G
LC
Single Mode
10km
1310nm
0 ~ 60 degrees C
10Gbps SFP+ (10GBASE-BX, Single Fiber Bi-directional SFP)
Model
Speed (Mbps)
Connector
Interface
Fiber Mode
Distance
Wavelength (TX)
Wavelength (RX)
Operating Temp.
MTB-LA20
MTB-LB20
10G
WDM(LC)
Single Mode
20km
1270nm
1330nm
0 ~ 60 degrees C
10G
WDM(LC)
Single Mode
20km
1330nm
1270nm
0 ~ 60 degrees C
MTB-LA40
MTB-LB40
10G
WDM(LC)
Single Mode
40km
1270nm
1330nm
0 ~ 60 degrees C
10G
WDM(LC)
Single Mode
40km
1330nm
1270nm
0 ~ 60 degrees C
MTB-LA60
MTB-LB60
10G
WDM(LC)
Single Mode
60km
1270nm
1330nm
0 ~ 60 degrees C
10G
WDM(LC)
Single Mode
60km
1330nm
1270nm
0 ~ 60 degrees C
1. It is recommended to use PLANET SFP on the Industrial Managed Switch. If you insert an
SFP/SFP+ transceiver that is not supported, the Industrial Managed Switch will not
recognize it.
2. Please choose the SFP/SFP+ transceiver which can be operated under -40~75 degrees C
temperature if the switch device is working in a 0~50 degrees C temperature environment.
1. Before we connect the Industrial Managed Switch to the other network device, we have to make sure both sides of the
SFP transceivers are with the same media type, for example: 1000BASE-SX to 1000BASE-SX, 1000BASE-LX to
1000BASE-LX.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement.
To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male
duplex LC connector type.
To connect to 1000BASE-LX SFP transceiver, please use the single-mode fiber cable with one side being the male
duplex LC connector type.
Connect the fiber cable
1. Insert the duplex LC connector into the SFP/SFP+ transceiver.
2. Connect the other end of the cable to a device with SFP/SFP+ transceiver installed.
3. Check the LNK/ACT LED of the SFP/SFP+ slot on the front of the Managed Switch. Ensure that the SFP/SFP+
transceiver is operating correctly.
4. Check the Link mode of the SFP/SFP+ port if the link fails. To function with some fiber-NICs or Media Converters, user
has to set the port Link mode to “10G FDX”, “1000M FDX” or “100M FDX”.