(V2) User Manual
- 5 - - 6 - - 7 - - 8 -
When primary port link failure occurs, the trac will swap to backup port
automatically.
Once the primary port status is back to link-up, the trac will swap from
backup port to primary port.
5. Product Specications
Model IGS-620TF
Hardware Specications
Copper Ports
4 x 10/100/1000BASE-T RJ45 TP
Auto-MDI/MDI-X, auto-negotiation
SFP Ports
2 x 100/1G/2.5GBASE-X SFP interfaces
Supports auto detection
DIP Switch
DIP Position Function
Fiber Mode
ON Fiber Redundancy
OFF (default) Switch Mode
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1;
Pin 3/4 for fault alarm;
Pin 5/6 for Power 2
Alarm
Provides one relay output for power failure
Alarm relay current carry ability: 1A @ DC 24V
ESD Protection 6KV DC
Enclosure IP30 type metal case
Installation DIN-rail kit and wall mount ear
Dimensions
(W x D x H)
32 x 87 x 135mm
Weight 425g
Power
Requirements
DC 12~48V or AC 24V
Redundant power with reverse polarity protection
Power Consumption /
Dissipation
7.5 watts/26BTU
Switch Specications
Switch Processing
Scheme
Store-and-Forward
Switch Fabric 18Gbps
Throughput
(packet per second)
13.39Mpps@64bytes
Address Table 4K entries
Jumbo Frame 9216 bytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Standards Conformance
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit
Ethernet
IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.1p Class of Service
Regulatory Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (Free fall)
IEC60068-2-27 (Shock)
IEC60068-2-6 (Vibration)
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
3.3 Installing the SFP Transceiver
The sections describe how to insert an SFP transceiver into an SFP port.
The SFP transceivers are hot-pluggable and hot-swappable. You can plug in
and out the transceiver to/from any SFP port without having to power down
the Industrial Gigabit Ethernet Switch as Figure 3-1 shows.
MGB / MFB
Series Module
Figure 3-1: Inserting the SFP Transceiver
Note
It is recommended to use PLANET SFP transceiver on the
Industrial Gigabit Ethernet Switch. If you insert an SFP
transceiver that is not supported, the Industrial Gigabit
Ethernet Switch will not recognize it.
PLANET Industrial Gigabit Ethernet Switch supports 100/1000/2500X with
both single mode and multi-mode SFP transceivers. Before we connect
Industrial Gigabit Ethernet Switch to the other network device, please do the
following:
1. Set the DIP Switch of SFP Port 1 or Port 2 to the “OFF” position with
ber speed auto detection.
DIP Position Function
Fiber Mode
ON Fiber Redundancy
OFF (default) Switch Mode
2. Make sure both sides of the SFP transceivers are with the same media
type, for example, 1000BASE-SX to 1000BASE-SX, and 1000BASE-LX to
1000BASE-LX.
Note
Never pull out the module without pulling the lever or the
push bolts on the module. Directly pulling out the module
with force could damage the module and the SFP port of the
Industrial Gigabit Ethernet Switch.
4. Fiber Redundancy Overview
The Industrial Gigabit Ethernet Switch provides rapid ber redundancy of
link for highly critical Ethernet applications. The redundancy mode supports
auto-recover function. If the destination port of a packet is link-down, it will
forward the packet to the other port of the backup pair. The following gure
shows the redundancy function.
Main Primary
Backup
Redundancy
< Primary Port >
Link Status : Up
Traffic Flow : Forwarding
< Backup Port >
Link Status : Down
Traffic Flow : Blocking
Main Primary
Backup
Redundancy
< Primary Port >
Link Status : Down
Traffic Flow : N/A
< Backup Port >
Link Status : Up
Traffic Flow : Forwarding
Traffic is changed from Primary-Port to Backup-Port
Link status auto detection and redundancy on dual ports with the same
connector type are featured.
Only when primary port is active, the backup port is blocked.
6. Physical Dimensions
The IGS-620TF Industrial Gigabit Ethernet Switch dimensions (W x D x H):
32 x 87.8 x 135mm
32.00
135.00
87.80
97.10
48.8046.50 39.70
28.00
48.80
53.50 53.50
18.00
15.20
30.00
9.20
40.00
28.00
18.00
28.00
18.00
28.00
28.00
40.00
163.00
Top View
Side View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Side View
Rear View
Unit: mm
Bottom View
LNK /
ACT
IGS-620TF
LNK /
ACT
SFP
P1 P2 Alarm
100/1G/2.5G
100/1G/2.5G
SFP
4
3
2
1
5
6
LNK/ACT
LNK/ACT
2.5G
1000
100
DC Input: 12-48V
, 0.8A
AC Input: 24V
, 0.6A
Switch
Redundant
Fiber
Mode
Fault Alarm loading: 24V, 1A
V1+ V2+
PWR1
PWR2Alarm
10/100
1000
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource on PLANET web site rst to check if it could solve your issue. If
you need more support information, please contact PLANET switch support
team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address:
support@planet.com.tw
Copyright PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.