User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET IGS-504HPT/IGS-614HPT
Industrial 5-/6-Port Gigabit Ethernet Switch with 4-Port PoE+. The
interfaces of these models are shown below:
Model Name
10/100/1000T
RJ45 Port
100/1000X SFP
Slot
PoE Port
IGS-504HPT 5 - 4
IGS-614HPT 5 1 4
In the following section, the term “Industrial PoE+ Switch”
means the IGS-504HPT/IGS-614HPT.
Open the box of the Industrial PoE+ Switch and carefully unpack it.
The box should contain the following items:
Industrial PoE+
Switch x 1
User’s Manual x 1
SFP Dust Cap x 1
(IGS-614HPT only)
Wall-mount Kit x 1 DIN-rail Kit x 1 RJ45 Dust Caps x 5
If any of these are missing or damaged, please contact your dealer
immediately.
Power Consumption
Max. 5.94
watts/20BTU
(Ethernet Full
Loading)
Max. 127
watts/433BTU
(Ethernet + PoE Full
Loading)
Max. 6.52
watts/22BTU
(Ethernet Full
Loading)
Max. 127
watts/433BTU
(Ethernet + PoE Full
Loading)
Dimensions
(W x D x H)
50 x 86 x 135 mm
Weight 611g 617g
Enclosure IP40 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
Switch Specications
Switch Architecture Store-and-Forward
Switch Fabric 10Gbps 12Gbps
Throughput
(packet per second)
7.4Mpps@64bytes 8.93Mpps@64bytes
Address Table 2K entries
Buer Memory 4M bits on-chip buer memory
Jumbo Frame 9Kbytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
90W Amber
Blinks to indicate that the PoE usage is around
75W to 89W.
Lights to indicate the PoE usage is around/over
90W.
120W Amber
Blinks to indicate that the PoE usage is around
100W to 119W.
Lights to indicate the PoE usage is at the
maximum.
 Per 802.3at PoE+ 10/100/1000BASE-T Interface
(Port 1 to Port 4)
LED Color Function
LNK/
ACT
Green
Lights to indicate the link through that port is
successfully established at 10Mbps or 100Mbps or
1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
PoE-in-
Use
Amber
Lights to indicate the port is providing DC in-line
power.
O to indicate the connected device is not a PoE
powered device (PD).
 Per 10/100/1000BASE-T Interface (Port 5)
LED Color Function
1000
LNK/
ACT
Green
Lights to indicate the port is successfully
established at 1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
3. Hardware Introduction
3.1 Switch Front Panel
P1 P2 Alarm
120W
PoE Usage
90W
60W
30W
4
5
3
2
1
LNK ACT
PoE-in-Use
1000
10/100
LNK/ACT
LNK/ACT
IGS-504HPT
1
P1 P2 Alarm
120W
PoE Usage
90W
60W
30W
4
6
5
3
2
1
LNK ACT
PoE-in-Use
1000
100
LNK/ACT
LNK/ACT
IGS-614HPT
2
1
Figure 3-1:
IGS-504HPT Front View
Figure 3-2:
IGS-614HPT Front View
1. Gigabit Ethernet TP Interfaces
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100
meters.
2.ProductSpecications
Model IGS-504HPT IGS-614HPT
Hardware Specications
Copper Ports
5 10/100/1000BASE-T RJ45 auto-MDI/
MDI-X ports
PoE Injector Ports
Four ports with 802.3at PoE+ injector
function (Port-1 to Port-4)
PoE Budget
DC12V: 60W
DC24V: 90W
DC48V~56V: 120W
SFP Slots --
1 1000BASE-SX/LX/
BX SFP interface
Compatible with
100BASE-FX SFP
interface
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1;
Pin 3/4 for fault alarm;
Pin 5/6 for Power 2
Alarm
One relay output for power failure.
Alarm relay current carry ability: 1A@DC
24V
Power Requirements
12~56V DC, 7A (max.)
Redundant power with reverse polarity
protection function
Stability Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3az Gigabit SX/LX (IGS-614HPT
only)
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Ecient Ethernet
(EEE)
IEEE 802.3at Power over Ethernet Plus PSE
IEEE 802.3af Power over Ethernet Plus
IEEE 802.1p Class of Service
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
2. 100/1000BASE-X SFP Slot (IGS-614HPT)
The SFP slot built in the IGS-614HPT supports SFP auto-detec-
tion and dual speed as it features 1000BASE-SX/LX/BX and
100BASE-FX SFP (small form-factor pluggable) ber-optic
modules. The distance can be extended from 550 meters to 2
kilometers (multi-mode ber) and 10/20/40/60/80/120 kilome-
ters (single-mode ber or WDM ber).
3.2 LED Indicators
 System
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Alarm Red
Lights to indicate either power 1 or power 2 has
no power.
 PoE Power Usage (Unit: Watt)
LED Color Function
30W Amber
O to indicate the PoE usage is less than 14W.
Blinks to indicate that the PoE usage is around
15W to 29W.
Lights to indicate the PoE usage is around/over
30W.
60W Amber
Blinks to indicate that the PoE usage is around
45W to 59W.
Lights to indicate the PoE usage is around/over
60W.
10/100
LNK/
ACT
Amber
Lights to indicate the port is successfully
established at 100Mbps or 10Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
 Per 1000BASE-X SFP Slot (Port 6 of IGS-614HPT)
LED Color Function
1000
LNK/
ACT
Green
Lights to indicate the port is successfully
established at 1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
100
LNK/
ACT
Amber
Lights to indicate the port is successfully
established at 100Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
3.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one
terminal block connector within two DC power inputs.
Figure 3-3 shows the upper panel of the Industrial PoE+ Switch.
AlarmPWR1 PWR2
Max. Fault Alarm Loading: 24V, 1A
DC Input:
12-56V , 7A max.
1 2 3 4 5 6
Figure 3-3: Industrial PoE+ Switch Upper Panel