User’s Manual of IGS-604HPT-M12 1
User’s Manual of IGS-604HPT-M12 Trademarks Copyright © PLANET Technology Corp. 2016. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
User’s Manual of IGS-604HPT-M12 TABLE OF CONTENTS 1. INTRODUCTION.................................................................................................................. 10 1.1 Package Contents ..................................................................................................................................... 10 1.2 Product Description .................................................................................................................................. 11 1.
User’s Manual of IGS-604HPT-M12 4.2.2 IP Configuration.................................................................................................................................................. 51 4.2.3 IP Status ............................................................................................................................................................. 53 4.2.4 Users Configuration ........................................................................................................
User’s Manual of IGS-604HPT-M12 4.5.1 Static Aggregation............................................................................................................................................. 101 4.5.2 LACP Configuration .......................................................................................................................................... 102 4.5.3 LACP System Status ....................................................................................................................
User’s Manual of IGS-604HPT-M12 4.8.12 MLD Snooping Port Group Filtering................................................................................................................ 171 4.8.13 MLD Snooping Status ..................................................................................................................................... 172 4.8.14 MLD Group Information ................................................................................................................................
User’s Manual of IGS-604HPT-M12 4.11.8 RADIUS Overview .......................................................................................................................................... 253 4.11.9 RADIUS Details .............................................................................................................................................. 255 4.11.10 Windows Platform RADIUS Server Configuration.........................................................................................
User’s Manual of IGS-604HPT-M12 4.16.6 PoE Status...................................................................................................................................................... 325 4.16.7 PoE Schedule................................................................................................................................................. 327 4.16.8 PoE Alive Check Configuration......................................................................................................
User’s Manual of IGS-604HPT-M12 A.2 10/100Mbps, 10/100BASE-TX................................................................................................................. 369 APPENDIX B : GLOSSARY ..................................................................................................
User’s Manual of IGS-604HPT-M12 1. INTRODUCTION Thank you for purchasing PLANET Industrial L2+ Managed Ethernet Switch. “Industrial Managed Switch” is used as an alternative name in this user’s manual. 1.1 Package Contents Open the box of the Industrial Managed Switch and carefully unpack it. The box should contain the following items: The Industrial Managed Switch x1 Quick Installation Guide x1 1.
User’s Manual of IGS-604HPT-M12 1.2 Product Description Suitable for Industrial Environment PLANET IGS-604HPT-M12, an Industrial Managed Ethernet Switch, comes with an IP67-rated industrial case, 4-port 10/100/1000T 802.3at PoE, 2-port 10/100/1000T, and static Layer 3 routing, providing a high level of immunity against electromagnetic interference and heavy electrical surges which are usually found on plant floors or in curb-side traffic control cabinets.
User’s Manual of IGS-604HPT-M12 Environmentally Hardened Design The IGS-604HPT-M12 is able to protect itself from dust and water ingress, and to operate under the temperature range from -40 to 75 degrees C. All these features ensure the highest level of reliability for mission-critical applications in any difficult environment.
User’s Manual of IGS-604HPT-M12 Built-in Unique PoE Functions for Surveillance Management As a managed PoE Switch for surveillance network, the IGS-604HPT-M12 features the following intelligent PoE management functions: PD Alive Check Scheduled Power Recycling SMTP/SNMP Trap Event Alert PoE Schedule Intelligent Powered Device Alive Check The IGS-604HPT-M12 can be configured to monitor a connected PD (Powered Device) status in real time via ping action.
User’s Manual of IGS-604HPT-M12 SMTP/SNMP Trap Event Alert Though most NVR or camera management software offers SMTP email alert function, the IGS-604HPT-M12 further provides event alert function to help to diagnose the abnormal device owing to whether or not there is a break of the network connection, loss of PoE power or the rebooting response by the PD Alive Check process.
User’s Manual of IGS-604HPT-M12 Redundant Ring, Fast Recovery for Critical Network Applications The IGS-604HPT-M12 supports redundant ring technology and features strong, rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates advanced ITU-T G.8032 ERPS (Ethernet Ring Protection Switching) technology, Spanning Tree Protocol (802.
User’s Manual of IGS-604HPT-M12 Layer 3 IPv4 and IPv6 VLAN Routing for Secure and Flexible Management The IGS-604HPT-M12 not only provides ultra high transmission performance, and excellent layer 2 and layer 4 technologies, but also layer 3 IPv4/IPv6 VLAN routing feature which allows to crossover different VLANs and different IP addresses for the purpose of having a highly-secure, flexibly-managed and simple networking application.
User’s Manual of IGS-604HPT-M12 1.3 How to Use This Manual This User’s Manual is structured as follows: Section 2, INSTALLATION The section explains the functions of the Industrial Managed Switch and how to physically install the Industrial Managed Switch. Section 3, SWITCH MANAGEMENT The section contains the information about the software function of the Industrial Managed Switch. Section 4, WEB CONFIGURATION The section explains how to manage the Industrial Managed Switch by Web interface.
User’s Manual of IGS-604HPT-M12 1.4 Product Features Physical Port 6-port 10/100/1000BASE-T waterproof and dustproof M12 connectors with 4-port IEEE 802.3at/af Power over Ethernet Injector function Hardware Conformance Complies with IEEE 802.3at Power over Ethernet Plus end-span PSE Complies with IEEE 802.3af Power over Ethernet end-span PSE Up to 4 ports of IEEE 802.3af/802.
User’s Manual of IGS-604HPT-M12 Up to 255 VLANs groups, out of 4095 VLAN IDs Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad) Private VLAN Edge (PVE) Protocol-based VLAN MAC-based VLAN IP subnet-based VLAN Voice VLAN Supports Spanning Tree Protocol IEEE 802.1D Spanning Tree Protocol (STP) IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) IEEE 802.1s Multiple Spanning Tree Protocol (MSTP), spanning tree by VLAN BPDU Guard Supports Link Aggregation 802.
User’s Manual of IGS-604HPT-M12 Security Authentication - IEEE 802.1x port-based/MAC-based network access authentication - IEEE 802.
User’s Manual of IGS-604HPT-M12 1.5 Product Specifications Product IGS-604HPT-M12 Hardware Specifications Copper Ports 6 x M12, 8-pin A-Coded female connector, 10/100/1000BASE-T auto-MDI/MDI-X ports PoE Injector Port 4 ports with 802.3at/af PoE injector function (Port-3 to Port-6) Power Connector 1 x M12, 5-pin A-Coded male connector Switch Architecture Store-and-Forward Switch Fabric 12Gbps/non-blocking Throughput 8.
User’s Manual of IGS-604HPT-M12 Port disable/enable Port Configuration Auto-negotiation 10/100/1000Mbps full and half duplex mode selection Flow control disable/enable Port Status Port Mirroring Display each port’s speed duplex mode, link status, flow control status, auto-negotiation status, trunk status TX/RX/Both Many-to-1 monitor 802.
User’s Manual of IGS-604HPT-M12 RFC 2863 Interface MIB RFC 4292 IP Forward MIB RFC 2665 Ether-Like MIB RFC 4293 IP MIB RFC 2819 RMON MIB RFC 4836 MAU-MIB (Groups 1, 2, 3 and 9) IEEE 802.1X PAE RFC 2737 Entity MIB LLDP RFC 2618 RADIUS Client Power over Ethernet MIB MIB Standards Conformance Regulatory Compliance FCC Part 15 Class A, CE IEC60068-2-32 (free fall) Stability Testing IEC60068-2-27 (shock) IEC60068-2-6 (vibration) Railway Traffic *EN50155 IEEE 802.1ab LLDP IEEE 802.
User’s Manual of IGS-604HPT-M12 2. INSTALLATION 2.1 Hardware Description This section describes the hardware features of Industrial Managed Switch. For easier management and control of the Industrial Managed Switch, familiarize yourself with its display indicators and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Industrial Managed Switch, read this chapter carefully. 2.1.
User’s Manual of IGS-604HPT-M12 2.1.2 Front Panel The front panel provides a simple interface monitoring the Managed Switch. Figure 2-1 shows the front panel of the Managed Switch. IGS-604HPT-M12 Front Panel Figure 2-1: IGS-604HPT-M12 Switch Front Panel ■ Gigabit TP Interface 10/100/1000BASE-T M12 copper: Up to 100 meters. ■ M12 DC Power Connector The front panel of the Managed Switch has an M12 DC power connector, which accepts DC power input voltage from -48V to -56V DC.
User’s Manual of IGS-604HPT-M12 2.1.3 LED Indications The front panel LEDs indicate instant status of power and system status, fan status, port links, PoE-in-use and data activity; they help monitor and troubleshoot when needed. Figure 2-2 shows the LED indications of the Managed Switch. IGS-604HPT-M12 LED Indication Figure 2-2: IGS-604HPT-M12 LED on Front Panel ■ LED Definition ■ System LED Color Function PWR1 Green Lights to indicate DC power input 1 has power.
User’s Manual of IGS-604HPT-M12 Lights to indicate that Ring state is in idle mode. R.O. Green Blinks to indicate that the Ring state is in protected mode. ■ Per 10/100/1000BASE-T Port (port 1~2) LED Color Function Lights 1000 LNK/ACT Indicating the port is running in 10/100/1000Mbps speed and successfully established. Green Blinks Indicating that the switch is actively sending or receiving data over that port.
User’s Manual of IGS-604HPT-M12 2.1.4 M12 10/100/1000T Connector Pin Assignment The Industrial Managed Switch front panel provides six 10/100/1000BASE-T Ethernet ports in the form of M12 8-pin A-coded female connector. These ports are designed for Ethernet equipment connection through Cat5/5e UTP cables. The M12 input interface pinout is shown below: 8-pin M12 Female 10/100/1000T Connector Pin Assignment 2.1.
User’s Manual of IGS-604HPT-M12 The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and colors of straight-through cable connection: Please make sure your waterproof RJ45 cables are with the same pin assignment and colors as the above picture before deploying the cables into your network. 2.1.
User’s Manual of IGS-604HPT-M12 M12 DC power cable pin assignment & wire code V1 positive (+) pin = black cable V1 negative (-) pin = brown cable V2 positive (+) pin = blue cable V2 negative (-) pin = white cable Make sure you connect the correct power pin to your DC power source. 1. The wire gauge for the power cable should be in the range of 12 ~ 24 AWG. 2. The DC power input range is 48 ~ 56V DC.
User’s Manual of IGS-604HPT-M12 2.2 Installing the Industrial Managed Switch This section describes how to install your Industrial Managed Switch and make connections to the Industrial Managed Switch. Please read the following topics and perform the procedures in the order being presented. To install your Industrial Managed Switch on a desktop or shelf, simply complete the following steps.
User’s Manual of IGS-604HPT-M12 Follow all the DIN-rail installation steps as shown in the example. Step 1: Screw the DIN-rail on the Industrial Managed Switch. Step 2: Lightly slide the DIN-rail into the track. Step 3: Check whether the DIN-rail is tightly on the track. Please refer to the following procedures to remove the Industrial Managed Switch from the track.
User’s Manual of IGS-604HPT-M12 Step 4: Lightly remove the DIN-rail from the track.
User’s Manual of IGS-604HPT-M12 2.2.3 Wall-mount Plate Mounting To install the Industrial Managed Switch on the wall, please follow the instructions below. Follow all the DIN-rail installation steps as shown in the example. Step 1: Remove the DIN-rail from the Industrial Managed Switch. Use the screwdriver to loosen the screws to remove the DIN-rail. Step 2: Place the wall-mount plate on the rear panel of the Industrial Managed Switch.
User’s Manual of IGS-604HPT-M12 Step 4: Use the hook holes at the corners of the wall mount plate to hang the Industrial Managed Switch on the wall. Step 5: To remove the wall-mount plate, reverse the steps above.
User’s Manual of IGS-604HPT-M12 2.2.4 Recovering Back to Default Configuration IP address has been changed or admin password has been forgotten – 1. Power off the Industrial Managed Switch and remove all the existing connections. 2. Use the M12 cable to connect to port 1 and port 2 in the loop topology as shown below: 3. Power on the Industrial Managed Switch and 6 LNK/ACT LEDs will be lit. 4. Resetting Industrial Managed Switch to the factory default is done when 6 LNK/ACT LEDs are lit again.
User’s Manual of IGS-604HPT-M12 3. SWITCH MANAGEMENT This chapter explains the methods that you can use to configure management access to the Industrial Managed Switch. It describes the types of management applications and the communication and management protocols that deliver data between your management device (workstation or personal computer) and the system. It also contains information about port connection options.
User’s Manual of IGS-604HPT-M12 3.2 Management Access Overview The Industrial Managed Switch gives you the flexibility to access and manage it using any or all of the following methods: Remote Telnet Interface Web browser Interface An external SNMP-based network management application The remote Telnet and Web browser interfaces are embedded in the Industrial Managed Switch software and are available for immediate use. Each of these management methods has their own advantages.
User’s Manual of IGS-604HPT-M12 3.3 CLI Mode Management Remote telnet is an IP-based protocol and console port is for user to operate the Industrial Managed Switch locally only; however, their operations are the same. The command line user interface is for performing system administration, such as displaying statistics or changing option settings.
User’s Manual of IGS-604HPT-M12 3.4 Web Management The Industrial Managed Switch offers management features that allow users to manage the Industrial Managed Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address for the Industrial Managed Switch, you can access the Industrial Managed Switch’s Web interface applications directly in your Web browser by entering the IP address of the Industrial Managed Switch.
User’s Manual of IGS-604HPT-M12 3.5 SNMP-based Network Management You can use an external SNMP-based application to configure and manage the Industrial Managed Switch, such as SNMP Network Manager, HP Openview Network Node Management (NNM) or What’s Up Gold. This management method requires the SNMP agent on the Industrial Managed Switch and the SNMP Network Management Station to use the same community string.
User’s Manual of IGS-604HPT-M12 3.6 PLANET Smart Discovery Utility To easily list the Industrial Managed Switch in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual CD-ROM is an ideal solution. The following install instructions guide you to running the Planet Smart Discovery Utility. 1. Open the Planet Smart Discovery Utility in administrator PC. 2. Run this utility and the following screen appears.
User’s Manual of IGS-604HPT-M12 1. This utility shows all the necessary information from the devices, such as MAC Address, Device Name, firmware version and Device IP Subnet address. A new password, IP Subnet address and description can be assigned to the devices. 2. After setup is completed, press the “Update Device”, “Update Multi” or “Update All” button to take effect. The meanings of the 3 buttons above are shown below: Update Device: Use the current setting on one single device.
User’s Manual of IGS-604HPT-M12 4. WEB CONFIGURATION This section introduces the configuration and functions of the Web-based management. About Web-based Management The Industrial Managed Switch offers management features that allow users to manage the Industrial Managed Switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. The Web-based Management supports Internet Explorer 8.0.
User’s Manual of IGS-604HPT-M12 http://192.168.0.100 2. When the following login screen appears, please enter the default username "admin" with password “admin” (or the username/password you have changed via console) to login the main screen of Industrial Managed Switch. The login screen in Figure 4-1-2 appears. Figure 4-1-2: Login Screen Default User name: admin Default Password: admin After entering the username and password, the main screen appears as Figure 4-1-3.
User’s Manual of IGS-604HPT-M12 Now, you can use the Web management interface to continue the switch management or manage the Industrial Managed Switch by Web interface. The Switch Menu on the left of the web page lets you access all the commands and statistics the Industrial Managed Switch provides. 1. It is recommended to use Internet Explore 8.0 or above to access Industrial Managed Switch. 2. The changed IP address takes effect immediately after clicking on the Save button.
User’s Manual of IGS-604HPT-M12 4.1 Main Web page The Industrial Managed Switch provides a Web-based browser interface for configuring and managing it. This interface allows you to access the Industrial Managed Switch using the Web browser of your choice. This chapter describes how to use the Industrial Managed Switch’s Web browser interface to configure and manage it.
User’s Manual of IGS-604HPT-M12 Main Menu Using the onboard web agent, you can define system parameters, manage and control the Industrial Managed Switch, and all its ports, or monitor network conditions. Via the Web-Management, the administrator can set up the Industrial Managed Switch by selecting the functions those listed in the Main Function. The screen in Figure 4-1-5 appears.
User’s Manual of IGS-604HPT-M12 4.2 System Use the System menu items to display and configure basic administrative details of the Industrial Managed Switch. Under System the following topics are provided to configure and view the system information. ■ System Information The Managed Switch system information is provided here. ■ IP Configuration Configures the Managed Switch with IPv4/IPv6 interface and IP routes on this page. ■ IP Status This page displays the status of the IP protocol layer.
User’s Manual of IGS-604HPT-M12 4.2.1 System Information The System Info page provides information for the current device information. System Info page helps a switch administrator to identify the hardware MAC address, software version and system uptime. The screen in Figure 4-2-1 appears. Figure 4-2-1: System Information Screenshot The page includes the following fields: Object Description Contact The system contact configured in Configuration | System | Information | System Contact.
User’s Manual of IGS-604HPT-M12 4.2.2 IP Configuration The IP Configuration includes the IP Configuration, IP Interface and IP Routes. The configured column is used to view or change the IP configuration. The maximum number of interfaces supported is 128 and the maximum number of routes is 32. The screen in Figure 4-2-2 appears. Figure 4-2-2: IP Configuration Screenshot The current column is used to show the active IP configuration.
User’s Manual of IGS-604HPT-M12 From this DHCP interface Specify from which DHCP-enabled interface a provided DNS server should be preferred. DNS Proxy When DNS proxy is enabled, system will relay DNS requests to the currently configured DNS server, and reply as a DNS resolver to the client devices on the network. IP Address Delete Select this option to delete an existing IP interface. VLAN The VLAN associated with the IP interface. Only ports in this VLAN will be able to access the IP interface.
User’s Manual of IGS-604HPT-M12 4.2.3 IP Status IP Status displays the status of the IP protocol layer. The status is defined by the IP interfaces, the IP routes and the neighbour cache (ARP cache) status. The screen in Figure 4-2-3 appears. Figure 4-2-3: IP Status Screenshot The page includes the following fields: Object Description IP Interfaces IP Routes Neighbor Cache Interface The name of the interface. Type The address type of the entry. This may be LINK or IPv4.
User’s Manual of IGS-604HPT-M12 4.2.4 Users Configuration This page provides an overview of the current users. Currently the only way to login as another user on the web server is to close and reopen the browser. After setup is completed, press the “Apply” button to take effect. Please login web interface with new user name and passwordas Figure 4-2-4 shows.
User’s Manual of IGS-604HPT-M12 Figure 4-2-5: Add/Edit User Configuration Screenshot The page includes the following fields: Object Description Username A string identifying the user name that this entry should belong to. The allowed string length is 1 to 31. The valid user name is a combination of letters, numbers and underscores. Password The password of the user. The allowed string length is 1 to 31. Password (again) Please enter the user’s new password here again to confirm.
User’s Manual of IGS-604HPT-M12 Generally, the privilege level 15 can be used for an administrator account, privilege level 10 for a standard user account and privilege level 5 for a guest account. Once the new user is added, the new user entry is shown on the Users Configuration page.
User’s Manual of IGS-604HPT-M12 4.2.5 Privilege Levels This page provides an overview of the privilege levels. After setup is completed, please press the “Apply” button to take effect. Please login web interface with new user name and password and the screen in Figure 4-2-7 appears.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Group Name The name identifying the privilege group. In most cases, a privilege level group consists of a single module (e.g. LACP, RSTP or QoS), but a few of them contain more than one. The following description defines these privilege level groups in details: System: Contact, Name, Location, Timezone, Log.
User’s Manual of IGS-604HPT-M12 4.2.6 NTP Configuration Configure NTP on this page. NTP is an acronym for Network Time Protocol, a network protocol for synchronizing the clocks of computer systems. NTP uses UDP (data grams) as transport layer. You can specify NTP Servers. The NTP Configuration screen in Figure 4-2-8 appears. Figure 4-2-8: NTP Configuration Screenshot The page includes the following fields: Object Description Mode Indicates the NTP mode operation.
User’s Manual of IGS-604HPT-M12 4.2.7 Time Configuration Configure Time Zone on this page. A Time Zone is a region that has a uniform standard time for legal, commercial, and social purposes. It is convenient for areas in close commercial or other communication to keep the same time, so time zones tend to follow the boundaries of countries and their subdivisions.
User’s Manual of IGS-604HPT-M12 the Daylight Saving Time configuration. Select 'Recurring' and configure the Daylight Saving Time duration to repeat the configuration every year. Select 'Non-Recurring' and configure the Daylight Saving Time duration for single time configuration. ( Default : Disabled ). Start Time Settings Week - Select the starting week number. Day - Select the starting day. Month - Select the starting month. Hours - Select the starting hour.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Mode Indicates the UPnP operation mode. Possible modes are: Enabled: Enable UPnP mode operation. Disabled: Disable UPnP mode operation. When the mode is enabled, two ACEs are added automatically to trap UPnP related packets to CPU. The ACEs are automatically removed when the mode is disabled. TTL The TTL value is used by UPnP to send SSDP advertisement messages. Valid values are in the range of 1 to 255.
User’s Manual of IGS-604HPT-M12 4.2.9 DHCP Relay Configure DHCP Relay on this page. DHCP Relay is used to forward and to transfer DHCP messages between the clients and the server when they are not on the same subnet domain. The DHCP option 82 enables a DHCP relay agent to insert specific information into a DHCP request packets when forwarding client DHCP packets to a DHCP server and remove the specific information from a DHCP reply packets when forwarding server DHCP packets to a DHCP client.
User’s Manual of IGS-604HPT-M12 forward and transfer DHCP messages between the clients and the server when they are not on the same subnet domain. Relay Information Mode Indicates the DHCP relay information mode option operation. Possible modes are: Enabled: Enable DHCP relay information mode operation.
User’s Manual of IGS-604HPT-M12 4.2.10 DHCP Relay Statistics This page provides statistics for DHCP relay. The DHCP Relay Statistics screen in Figure 4-2-13 appears. Figure 4-2-13: DHCP Relay Statistics Screenshot The page includes the following fields: Server Statistics Object Description Transmit to Server The packets number that is relayed from client to server. Transmit Error The packets number whose errors are sending to clients.
User’s Manual of IGS-604HPT-M12 Receive from Client The packets number that is received from server. Receive Agent Option The packets number that is received with relay agent information option. Replace Agent Option The packets number that is replaced with relay agent information option. Keep Agent Option The packets number that keeps relay agent information option. Drop Agent Option The packets number that drops relay agent information option.
User’s Manual of IGS-604HPT-M12 4.2.11 CPU Load This page displays the CPU load, using an SVG graph. The load is measured as average over the last 100ms, 1sec and 10 seconds intervals. The last 120 samples are graphed, and the last numbers are displayed as text as well. In order to display the SVG graph, your browser must support the SVG format. Consult the SVG Wiki for more information on browser support.
User’s Manual of IGS-604HPT-M12 4.2.12 System Log The Industrial Managed Switch system log information is provided here. The System Log screen in Figure 4-2-15 appears. Figure 4-2-15: System Log Screenshot The page includes the following fields: Object Description ID The ID (>= 1) of the system log entry. Level The level of the system log entry. The following level types are supported: Info: Information level of the system log. Warning: Warning level of the system log.
User’s Manual of IGS-604HPT-M12 : Downloads the selected log entries. : Updates the system log entries, starting from the first available entry ID. : Updates the system log entries, ending at the last entry currently displayed. : Updates the system log entries, starting from the last entry currently displayed. : Updates the system log entries, ending at the last available entry ID. 4.2.13 Detailed Log The Industrial Managed Switch system detailed log information is provided here.
User’s Manual of IGS-604HPT-M12 4.2.14 Remote Syslog Configure remote syslog on this page. The Remote Syslog screen in Figure 4-2-17 appears. Figure 4-2-17: Remote Syslog Screenshot The page includes the following fields: Object Description Mode Indicates the server mode operation. When the mode operation is enabled, the syslog message will send out to syslog server.
User’s Manual of IGS-604HPT-M12 4.2.15 SMTP Configuration This page facilitates an SMTP Configuration on the switch. The SMTP Configure screen in Figure 4-2-18 appears. Figure 4-2-18: SMTP Configuration Screenshot The page includes the following fields: Object Description SMTP Mode Controls whether SMTP is enabled on this switch. SMTP Server Type the SMTP server name or the IP address of the SMTP server. SMTP Port Set port number of SMTP service.
User’s Manual of IGS-604HPT-M12 4.2.16 Fault Alarm This page facilitates an update of the firmware controlling the switch. The Web Firmware Upgrade screen in Figure 4-2-19 appears. Figure 4-2-19: Fault Alarm Control Configuration Screenshot The page includes the following fields: Object Description Enable Controls whether Fault Alarm is enabled on this switch. Record Controls whether Record is sending System log or SNMP Trap or both.
User’s Manual of IGS-604HPT-M12 4.2.17 Web Firmware Upgrade This page facilitates an update of the firmware controlling the switch. The Web Firmware Upgrade screen in Figure 4-2-20 appears. Figure 4-2-20: Web Firmware Upgrade Screenshot To open Firmware Upgrade screen, perform the following: 1. Click System -> Web Firmware Upgrade. 2. The Firmware Upgrade screen is displayed as in Figure 4-2-21. 3. Click the “ 4. Select on the firmware then click “ 5.
User’s Manual of IGS-604HPT-M12 4.2.18 TFTP Firmware Upgrade The Firmware Upgrade page provides the functions to allow a user to update the Industrial Managed Switch firmware from the TFTP server in the network. Before updating, make sure you have your TFTP server ready and the firmware image is on the TFTP server. The TFTP Firmware Upgrade screen in Figure 4-2-22 appears.
User’s Manual of IGS-604HPT-M12 4.2.19 Save Startup Config This function allows to save the current configuration, thereby ensuring that the current active configuration can be used at the next reboot screen in Figure 4-2-23 as shown below. After saving the configuration, the screen in Figure 4-2-24 appears. Figure 4-2-23: Configuration Save Screenshot Figure 4-2-24: Finish Saving Screenshot 4.2.20 Configuration Download The switch stores its configuration in a number of text files in CLI format.
User’s Manual of IGS-604HPT-M12 4.2.21 Configuration Upload Configuration Upload page allows the uploads of the running-config and startup-config on the switch. Please refer to Figure 4-2-26 shown below. Figure 4-2-26: Configuration Upload Screenshot If the destination is running-config, the file will be applied to the switch configuration. This can be done in two ways: Replace mode: The current configuration is fully replaced with the configuration in the uploaded file.
User’s Manual of IGS-604HPT-M12 It is possible to activate any of the configuration files present on the switch, except for running-config which represents the currently active configuration. . This will initiate the process of completely replacing the existing Select the file to activate and click configuration with that of the selected file. 4.2.23 Configuration Delete Configuration Delete page allows to delete the startup-config and default-config files which are stored in FLASH.
User’s Manual of IGS-604HPT-M12 Figure 4-2-29: Software Image Selection Screenshot The page includes the following fields: Object Description Image The flash index name of the firmware image. The name of primary (preferred) image is image, the alternate image is named image.bk. Version The version of the firmware image. Date The date where the firmware was produced. Buttons : Click to use the alternate image. This button may be disabled depending on system state. 4.2.
User’s Manual of IGS-604HPT-M12 Buttons : Click to reset the configuration to Factory Defaults. : Click to return to the Port State page without resetting the configuration. To reset the Industrial Managed Switch to the Factory default setting, you can also press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of 192.168.0.xx. 4.2.
User’s Manual of IGS-604HPT-M12 4.3 Simple Network Management Protocol 4.3.1 SNMP Overview The Simple Network Management Protocol (SNMP) is an application layer protocol that facilitates the exchange of management information between network devices. It is part of the Transmission Control Protocol/Internet Protocol (TCP/IP) protocol suite. SNMP enables network administrators to manage network performance, find and solve network problems, and plan for network growth.
User’s Manual of IGS-604HPT-M12 SNMP community An SNMP community is the group that devices and management stations running SNMP belong to. It helps define where information is sent. The community name is used to identify the group. A SNMP device or agent may belong to more than one SNMP community. It will not respond to requests from management stations that do not belong to one of its communities.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Mode Indicates the SNMP mode operation. Possible modes are: Enabled: Enable SNMP mode operation. Disabled: Disable SNMP mode operation. Version Indicates the SNMP supported version. Possible versions are: SNMP v1: Set SNMP supported version 1. SNMP v2c: Set SNMP supported version 2c. SNMP v3: Set SNMP supported version 3.
User’s Manual of IGS-604HPT-M12 4.3.3 SNMP Trap Configuration Configure SNMP trap on this page. The SNMP Trap Configuration screen in Figure 4-3-2 appears. Figure 4-3-2: SNMP Trap Configuration Screenshot The page includes the following fields: Object Description Trap Config Indicates which trap Configuration's name for configuring. The allowed string length is 0 to 255, and the allowed content is ASCII characters from 33 to 126. Trap Mode Indicates the SNMP trap mode operation.
User’s Manual of IGS-604HPT-M12 Trap Community Indicates the community access string when send SNMP trap packet. The allowed string length is 0 to 255, and the allowed content is the ASCII characters from 33 to 126. Trap Destination Indicates the SNMP trap destination address. Address Trap Destination Port Indicates the SNMP trap destination port. SNMP Agent will send SNMP message via this port, the port range is 1~65535. Trap Inform Mode Indicates the SNMP trap inform mode operation.
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.3.4 SNMP System Information The switch system information is provided here. The SNMP System Information screen in Figure 4-3-3 appears.
User’s Manual of IGS-604HPT-M12 4.3.5 SNMPv3 Configuration 4.3.5.1 SNMPv3 Communities Configure SNMPv3 communities table on this page. The entry index key is Community. The SNMPv3 Communities screen in Figure 4-3-4 appears. Figure 4-3-4: SNMPv3 Communities Configuration Screenshot The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. Community Indicates the community access string to permit access to SNMPv3 agent.
User’s Manual of IGS-604HPT-M12 4.3.5.2 SNMPv3 Users Configure SNMPv3 users table on this page. The entry index keys are Engine ID and User Name. The SNMPv3 Users screen in Figure 4-3-5 appears. Figure 4-3-5: SNMPv3 Users Configuration Screenshot The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. Engine ID An octet string identifying the engine ID that this entry should belong to.
User’s Manual of IGS-604HPT-M12 MD5: An optional flag to indicate that this user using MD5 authentication protocol. SHA: An optional flag to indicate that this user using SHA authentication protocol. The value of security level cannot be modified if entry already exist. That means must first ensure that the value is set correctly. Authentication A string identifying the authentication pass phrase. For MD5 authentication protocol, the allowed string length is 8 to 32.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. Security Model Indicates the security model that this entry should belong to. Possible security models are: v1: Reserved for SNMPv1. v2c: Reserved for SNMPv2c. usm: User-based Security Model (USM). Security Name A string identifying the security name that this entry should belong to.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. View Name A string identifying the view name that this entry should belong to. The allowed string length is 1 to 32, and the allowed content is the ASCII characters from 33 to 126. View Type Indicates the view type that this entry should belong to.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. Group Name A string identifying the group name that this entry should belong to. The allowed string length is 1 to 32, and the allowed content is the ASCII characters from 33 to 126. Security Model Indicates the security model that this entry should belong to.
User’s Manual of IGS-604HPT-M12 4.4 Port Management Use the Port Menu to display or configure the Industrial Managed Switch's ports. This section has the following items: Port Configuration Configures port connection settings Port Statistics Overview Lists Ethernet and RMON port statistics Port Statistics Detail Lists Ethernet and RMON port statistics Port Mirror Sets the source and target ports for mirroring 4.4.1 Port Configuration This page displays current port configurations.
User’s Manual of IGS-604HPT-M12 Flow Control Disable - Shutdown the port manually. When Auto Speed is selected on a port, this section indicates the flow control capability that is advertised to the link partner. When a fixed-speed setting is selected, that is what is used. The Current Rx column indicates whether pause frames on the port are obeyed, and the Current Tx column indicates whether pause frames on the port are transmitted.
User’s Manual of IGS-604HPT-M12 4.4.2 Port Statistics Overview This page provides an overview of general traffic statistics for all switch ports. The Port Statistics Overview screen in Figure 4-4-2 appears. Figure 4-4-2: Port Statistics Overview Screenshot The displayed counters are: Object Description Port The logical port for the settings contained in the same row. Packets The number of received and transmitted packets per port. Bytes The number of received and transmitted bytes per port.
User’s Manual of IGS-604HPT-M12 4.4.3 Port Statistics Detail This page provides detailed traffic statistics for a specific switch port. Use the port select box to select which switch port details to display. The selected port belong to the currently selected stack unit, as reflected by the page header. The displayed counters are the totals for receive and transmit, the size counters for receive and transmit, and the error counters for receive and transmit.
User’s Manual of IGS-604HPT-M12 Receive and Transmit Size Counters The number of received and transmitted (good and bad) packets split into categories based on their respective frame sizes. Receive and Transmit Queue Counters The number of received and transmitted packets per input and output queue. Receive Error Counters Object Description Rx Drops The number of frames dropped due to lack of receive buffers or egress congestion.
User’s Manual of IGS-604HPT-M12 4.4.4 Port Mirror Configure port Mirroring on this page. This function provides monitoring network traffic that forwards a copy of each incoming or outgoing packet from one port of a network Switch to another port where the packet can be studied. It enables the manager to keep close track of switch performance and alter it if necessary.
User’s Manual of IGS-604HPT-M12 Figure 4-4-5: Mirror Configuration Screenshot The page includes the following fields: Object Description Port to mirror on Frames from ports that have either source (rx) or destination (tx) mirroring enabled are mirrored to this port. Disabled disables mirroring. Port The logical port for the settings contained in the same row. Mode Select mirror mode. ■ Rx only: Frames received at this port are mirrored to the mirroring port.
User’s Manual of IGS-604HPT-M12 4.5 Link Aggregation Port Aggregation optimizes port usage by linking a group of ports together to form a single Link Aggregated Groups (LAGs). Port Aggregation multiplies the bandwidth between the devices, increases port flexibility, and provides link redundancy. Each LAG is composed of ports of the same speed, set to full-duplex operations. Ports in a LAG, can be of different media types (UTP/Fiber, or different fiber types), provided they operate at the same speed.
User’s Manual of IGS-604HPT-M12 The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner Systems that require high speed redundant links. Link aggregation lets you group up to eight consecutive ports into a single dedicated connection. This feature can expand bandwidth to a device on the network. LACP operation requires full-duplex mode, more detail information refer to the IEEE 802.3ad standard.
User’s Manual of IGS-604HPT-M12 4.5.1 Static Aggregation This page is used to configure the Aggregation hash mode and the aggregation group. The aggregation hash mode settings are global, whereas the aggregation group relate to the currently selected stack unit, as reflected by the page header. Hash Code Contributors The Static Aggregation screen in Figure 4-5-2 appears.
User’s Manual of IGS-604HPT-M12 Figure 4-5-3: Aggregation Group Configuration Screenshot The page includes the following fields: .Object Description Group ID Indicates the group ID for the settings contained in the same row. Group ID "Normal" indicates there is no aggregation. Only one group ID is valid per port. Port Members Each switch port is listed for each group ID. Select a radio button to include a port in an aggregation, or clear the radio button to remove the port from the aggregation.
User’s Manual of IGS-604HPT-M12 Figure 4-5-4 : LACP Port Configuration Screenshot The page includes the following fields: Object Description Port The switch port number. LACP Enabled Controls whether LACP is enabled on this switch port. LACP will form an aggregation when 2 or more ports are connected to the same partner. LACP can form max 12 LAGs per switch and 2G LAGs per stack. Key The Key value incurred by the port, range 1-65535 .
User’s Manual of IGS-604HPT-M12 4.5.3 LACP System Status This page provides a status overview for all LACP instances. The LACP Status page displays the current LACP aggregation Groups and LACP Port status. The LACP System Status screen in Figure 4-5-5 appears. Figure 4-5-5: LACP System Status Screenshot The page includes the following fields: Object Description Aggr ID The Aggregation ID associated with this aggregation instance.
User’s Manual of IGS-604HPT-M12 4.5.4 LACP Port Status This page provides a status overview for LACP status for all ports. The LACP Port Status screen in Figure 4-5-6 appears. Figure 4-5-6: LACP Status Screenshot The page includes the following fields: Object Description Port The switch port number. LACP 'Yes' means that LACP is enabled and the port link is up. 'No' means that LACP is not enabled or that the port link is down.
User’s Manual of IGS-604HPT-M12 4.5.5 LACP Port Statistics This page provides an overview for LACP statistics for all ports. The LACP Port Statistics screen in Figure 4-5-7 appears. Figure 4-5-7: LACP Statistics Screenshot The page includes the following fields: Object Description Port The switch port number. LACP Received Shows how many LACP frames have been sent from each port. LACP Transmitted Shows how many LACP frames have been received at each port.
User’s Manual of IGS-604HPT-M12 4.6 VLAN 4.6.1 VLAN Overview A Virtual Local Area Network (VLAN) is a network topology configured according to a logical scheme rather than the physical layout. VLAN can be used to combine any collection of LAN segments into an autonomous user group that appears as a single LAN. VLAN also logically segment the network into different broadcast domains so that packets are forwarded only between ports within the VLAN.
User’s Manual of IGS-604HPT-M12 4.6.2 IEEE 802.1Q VLAN In large networks, routers are used to isolate broadcast traffic for each subnet into separate domains. This Industrial Managed Switch provides a similar service at Layer 2 by using VLANs to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This also provides a more secure and cleaner network environment. An IEEE 802.
User’s Manual of IGS-604HPT-M12 ■ 802.1Q VLAN Tags The figure below shows the 802.1Q VLAN tag. There are four additional octets inserted after the source MAC address. Their presence is indicated by a value of 0x8100 in the Ether Type field. When a packet's Ether Type field is equal to 0x8100, the packet carries the IEEE 802.1Q/802.1p tag.
User’s Manual of IGS-604HPT-M12 Every physical port on a switch has a PVID. 802.1Q ports are also assigned a PVID, for use within the switch. If no VLAN are defined on the switch, all ports are then assigned to a default VLAN with a PVID equal to 1. Untagged packets are assigned the PVID of the port on which they were received. Forwarding decisions are based upon this PVID, in so far as VLAN are concerned. Tagged packets are forwarded according to the VID contained within the tag.
User’s Manual of IGS-604HPT-M12 ■ Port Overlapping Port overlapping can be used to allow access to commonly shared network resources among different VLAN groups, such as file servers or printers. Note that if you implement VLANs which do not overlap, but still need to communicate, you can connect them by enabled routing on this switch. ■ Untagged VLANs Untagged (or static) VLANs are typically used to reduce broadcast traffic and to increase security.
User’s Manual of IGS-604HPT-M12 ■ IEEE 802.1Q Tunneling (Q-in-Q) IEEE 802.1Q Tunneling (QinQ) is designed for service providers carrying traffic for multiple customers across their networks. QinQ tunneling is used to maintain customer-specific VLAN and Layer 2 protocol configurations even when different customers use the same internal VLAN IDs.
User’s Manual of IGS-604HPT-M12 Global VLAN Configuration The Global VLAN Configuration screen in Figure 4-6-1 appears. Figure 4-6-1 : Global VLAN Configuration Screenshot The page includes the following fields: Object Description Allowed Access This field shows the allowed Access VLANs, it only affects ports configured as VLANs Access ports. Ports in other modes are members of all VLANs specified in the Allowed VLANs field. By default, only VLAN 1 is enabled.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Port This is the logical port number for this row. Mode Access Access ports are normally used to connect to end stations. Dynamic features like Voice VLAN may add the port to more VLANs behind the scenes.
User’s Manual of IGS-604HPT-M12 The Port VLAN is called an "Access VLAN" for ports in Access mode and Native VLAN for ports in Trunk or Hybrid mode. Port Type Ports in hybrid mode allow for changing the port type, that is, whether a frame's VLAN tag is used to classify the frame on ingress to a particular VLAN, and if so, which TPID it reacts on. Likewise, on egress, the Port Type determines the TPID of the tag, if a tag is required.
User’s Manual of IGS-604HPT-M12 Only untagged frames are accepted on ingress. Tagged frames are discarded. Egress Tagging This option is only available for ports in Hybrid mode. Ports in Trunk and Hybrid mode may control the tagging of frames on egress. ■ Untag Port VLAN Frames classified to the Port VLAN are transmitted untagged. Other frames are transmitted with the relevant tag. ■ Tag All All frames, whether classified to the Port VLAN or not, are transmitted with a tag.
User’s Manual of IGS-604HPT-M12 4.6.4 VLAN Membership Status This page provides an overview of membership status for VLAN users. The VLAN Membership Status screen in Figure 4-6-4 appears. Figure 4-6-4: VLAN Membership Status for Static User Screenshot The page includes the following fields: Object Description VLAN User A VLAN User is a module that uses services of the VLAN management functionality to configure VLAN memberships and VLAN port configuration such as PVID, UVID.
User’s Manual of IGS-604HPT-M12 Buttons : Select VLAN Users from this drop down list. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. : Updates the table starting from the first entry in the VLAN Table, i.e. the entry with the lowest VLAN ID. : Updates the table, starting with the entry after the last entry currently displayed. 4.6.5 VLAN Port Status This page provides VLAN Port Status.
User’s Manual of IGS-604HPT-M12 frames, untagged frames received on that port are discarded. Port VLAN ID Shows the PVID setting for the port. Tx Tag Shows egress filtering frame status whether tagged or untagged. Untagged VLAN ID Shows UVID (untagged VLAN ID). Port's UVID determines the packet's behavior at the egress side. Conflicts Shows status of Conflicts whether exists or Not.
User’s Manual of IGS-604HPT-M12 Figure 4-6-6 Private VLAN Membership Configuration Screenshot The page includes the following fields: Object Description Delete To delete a private VLAN entry, check this box. The entry will be deleted during the next save. Private VLAN ID Indicates the ID of this particular private VLAN. Port Members A row of check boxes for each port is displayed for each private VLAN ID. To include a port in a Private VLAN, check the box.
User’s Manual of IGS-604HPT-M12 : Click to refresh the page immediately. 4.6.7 Port Isolation Overview When a VLAN is configured to be a private VLAN, communication between ports within that VLAN can be prevented. Two application examples are provided in this section: Customers connected to an ISP can be members of the same VLAN, but they are not allowed to communicate with each other within that VLAN.
User’s Manual of IGS-604HPT-M12 Isolated ports — Ports from which traffic can only be forwarded to promiscuous ports in the private VLAN — Ports which can receive traffic from only promiscuous ports in the private VLAN The configuration of promiscuous and isolated ports applies to all private VLANs. When traffic comes in on a promiscuous port in a private VLAN, the VLAN mask from the VLAN table is applied.
User’s Manual of IGS-604HPT-M12 4.6.8 VLAN setting example: Separate VLAN 802.1Q VLAN Trunk Port Isolate 4.6.8.1 Two Separate 802.1Q VLANs The diagram shows how the Industrial Managed Switch handle Tagged and Untagged traffic flow for two VLANs. VLAN Group 2 and VLAN Group 3 are separated VLAN. Each VLAN isolate network traffic so only members of the VLAN receive traffic from the same VLAN members.
User’s Manual of IGS-604HPT-M12 The scenario is described as follows: Untagged packet entering VLAN 2 1. While [PC-1] transmit an untagged packet enters Port-1, the Industrial Managed Switch will tag it with a VLAN Tag=2. [PC-2] and [PC-3] will received the packet through Port-2 and Port-3. 2. [PC-4],[PC-5] and [PC-6] received no packet. 3. While the packet leaves Port-2, it will be stripped away it tag becoming an untagged packet. 4.
User’s Manual of IGS-604HPT-M12 2. Assign VLAN Member and PVID to each port: VLAN 2 : Port-1,Port-2 and Port-3 VLAN 3 : Port-4, Port-5 and Port-6 VLAN 1 : All other ports – Port-7~Port-28 Figure 4-6-10: Change Port VLAN of Port 1~3 to be VLAN2 and Port VLAN of Port 4~6 to be VLAN3 3. Enable VLAN Tag for specific ports Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3) Change Port 3 Mode as Trunk and select Egress Tagging as Tag All and Type 2 in the Allowed VLANs column.
User’s Manual of IGS-604HPT-M12 4.6.8.2 VLAN Trunking between two 802.1Q aware switches In most cases, they are used for “Uplink” to other switches. VLANs are separated at different switches, but they need to access to other switches within the same VLAN group. The screen in Figure 4-6-12 appears. Figure 4-6-12: VLAN Trunking Diagram Setup steps 1. Add VLAN Group Add two VLANs – VLAN 2 and VLAN 3 For Type 1-3 in Allowed Access VLANs column, the 1-3 includes VLAN1 and 2 and 3.
User’s Manual of IGS-604HPT-M12 2. Assign VLAN Member and PVID to each port: VLAN 2 : Port-1,Port-2 and Port-3 VLAN 3 : Port-4, Port-5 and Port-6 VLAN 1 : All other ports – Port-7~Port-48 Figure 4-6-14: Changes Port VLAN of Port 1~3 to be VLAN2 and Port VLAN of Port 4~6 to be VLAN3 For the VLAN ports connecting to the hosts, please refer to 4.6.10.1. The following steps focus on the VLAN Trunk port configuration. 1. Specify Port-7 to be the 802.1Q VLAN Trunk port. 2.
User’s Manual of IGS-604HPT-M12 VLAN 2 members of Port-1 to Port-3 and VLAN 3 members of Port-4 to Port-6 also belong to VLAN 1. But with different PVID settings, packets from VLAN 2 or VLAN 3 are not able to access to the other VLAN. 6. Repeat Steps 1 to 6 to set up the VLAN Trunk port at the partner switch. To add more VLANs to join the VLAN trunk, repeat Steps 1 to 3 to assign the Trunk port to the VLANs. 4.6.8.
User’s Manual of IGS-604HPT-M12 Figure 4-6-17: The Configuration of Isolated and Promiscuous Port 2. Assign VLAN Member : VLAN 1 : Port-5 and Port-6 VLAN 2 : Port-1, Port-2, Port-5 and Port-6 VLAN 3: Port-3~Port-6. The screen in Figure 4-6-18 appears.
User’s Manual of IGS-604HPT-M12 4.6.9 MAC-based VLAN The MAC-based VLAN entries can be configured here. This page allows for adding and deleting MAC-based VLAN entries and assigning the entries to different ports. This page shows only static entries. The MAC-based VLAN screen in Figure 4-6-18 appears. Figure 4-6-18: MAC-based VLAN Membership Configuration Screenshot The page includes the following fields: Object Description Delete To delete a MAC-based VLAN entry, check this box and press save.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add a new MAC-based VLAN entry. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. : Updates the table starting from the first entry in the MAC-based VLAN Table. : Updates the table, starting with the entry after the last entry currently displayed. 4.6.
User’s Manual of IGS-604HPT-M12 Note: On changing the Frame type field, valid value of the following text field will vary depending on the new frame type you selected. Value Valid value that can be entered in this text field depends on the option selected from the preceding Frame Type selection menu. Below is the criteria for three different Frame Types: 1. For Ethernet: Values in the text field when Ethernet is selected as a Frame Type is called etype.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add a new entry in mapping table. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately.
User’s Manual of IGS-604HPT-M12 4.6.11 Protocol-based VLAN Membership This page allows you to map a already configured Group Name to a VLAN for the switch. The Group Name to VLAN Mapping Table screen in Figure 4-6-20 appears. Figure 4-6-20 Group Name to VLAN Mapping Table Screenshot The page includes the following fields: Object Description Delete To delete a Group Name to VLAN map entry, check this box.
User’s Manual of IGS-604HPT-M12 4.7 Spanning Tree Protocol 4.7.1 Theory The Spanning Tree protocol can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers. This allows the switch to interact with other bridging devices in your network to ensure that only one route exists between any two stations on the network, and provide backup links which automatically take over when a primary link goes down.
User’s Manual of IGS-604HPT-M12 The path cost to the root from the transmitting port The port identifier of the transmitting port The switch sends BPDUs to communicate and construct the spanning-tree topology. All switches connected to the LAN on which the packet is transmitted will receive the BPDU. BPDUs are not directly forwarded by the switch, but the receiving switch uses the information in the frame to calculate a BPDU, and, if the topology changes, initiates a BPDU transmission.
User’s Manual of IGS-604HPT-M12 From forwarding to disabled From disabled to blocking Figure 4-7-1: STP Port State Transitions You can modify each port state by using management software. When you enable STP, every port on every switch in the network goes through the blocking state and then transitions through the states of listening and learning at power up. If properly configured, each port stabilizes to the forwarding or blocking state.
User’s Manual of IGS-604HPT-M12 The following are the user-configurable STP parameters for the switch level: Parameter Description Default Value Bridge Identifier(Not user A combination of the User-set priority and the 32768 + MAC configurable switch’s MAC address.
User’s Manual of IGS-604HPT-M12 User-Changeable STA Parameters The Switch’s factory default setting should cover the majority of installations. However, it is advisable to keep the default settings as set at the factory; unless, it is absolutely necessary. The user changeable parameters in the Switch are as follows: Priority – A Priority for the switch can be set from 0 to 65535. 0 is equal to the highest Priority. Hello Time – The Hello Time can be from 1 to 10 seconds.
User’s Manual of IGS-604HPT-M12 and Port Cost settings is, however, relatively straight forward. Figure 4-7-2: Before Applying the STA Rules In this example, only the default STP values are used.
User’s Manual of IGS-604HPT-M12 The switch with the lowest Bridge ID (switch C) was elected the root bridge, and the ports were selected to give a high port cost between switches B and C. The two (optional) Gigabit ports (default port cost = 20,000) on switch A are connected to one (optional) Gigabit port on both switch B and C. The redundant link between switch B and C is deliberately chosen as a 100 Mbps Fast Ethernet link (default port cost = 200,000).
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Basic Settings Object Description Protocol Version The STP protocol version setting. Valid values are: STP (IEEE 802.1D Spanning Tree Protocol) RSTP (IEEE 802.2w Rapid Spanning Tree Protocol) MSTP (IEEE 802.1s Multiple Spanning Tree Protocol) Bridge Priority Controls the bridge priority. Lower numeric values have better priority.
User’s Manual of IGS-604HPT-M12 Port Error Recovery Control whether a port in the error-disabled state automatically will be enabled after a certain time. If recovery is not enabled, ports have to be disabled and re-enabled for normal STP operation. The condition is also cleared by a system reboot. Port Error Recovery The time that has to pass before a port in the error-disabled state can be enabled. Valid values are between 30 and 86400 seconds (24 hours).
User’s Manual of IGS-604HPT-M12 sum of the Port Path Costs on the least cost path to the Root Bridge. Topology Flag The current state of the Topology Change Flag for this Bridge instance. Topology Change Last The time since last Topology Change occurred. Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to refresh the page immediately. 4.7.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Port The switch port number of the logical STP port. STP Enabled Controls whether RSTP is enabled on this switch port. Path Cost Controls the path cost incurred by the port. The Auto setting will set the path cost as appropriate by the physical link speed, using the 802.1D recommended values. Using the Specific setting, a user-defined value can be entered.
User’s Manual of IGS-604HPT-M12 A port entering error-disabled state due to this setting is subject to the bridge Port Error Recovery setting as well. Point-to-point Controls whether the port connects to a point-to-point LAN rather than a shared medium. This can be automatically determined, or forced either true or false. Transitions to the forwarding state is faster for point-to-point LANs than for shared media.
User’s Manual of IGS-604HPT-M12 Port Type Link Type IEEE 802.1w-2001 Ethernet Half Duplex 2,000,000 Full Duplex 1,000,000 Trunk 500,000 Half Duplex 200,000 Full Duplex 100,000 Trunk 50,000 Full Duplex 10,000 Trunk 5,000 Fast Ethernet Gigabit Ethernet Table 4-7-3: Default STP Path Costs 4.7.5 MSTI Priorities This page allows the user to inspect the current STP MSTI bridge instance priority configurations, and possibly change them as well.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description MSTI The bridge instance. The CIST is the default instance, which is always active. Priority Controls the bridge priority. Lower numerical values have better priority. The bridge priority plus the MSTI instance number, concatenated with the 6-byte MAC address of the switch forms a Bridge Identifier.
User’s Manual of IGS-604HPT-M12 4.7.6 MSTI Configuration This page allows the user to inspect the current STP MSTI bridge instance priority configurations, and possibly change them as well. The MSTI Configuration screen in Figure 4-7-8 appears. Figure 4-7-8: MSTI Configuration Screenshot The page includes the following fields: Configuration Identification Object Description Configuration Name The name identifying the VLAN to MSTI mapping.
User’s Manual of IGS-604HPT-M12 MSTI Mapping Object Description MSTI The bridge instance. The CIST is not available for explicit mapping, as it will receive the VLANs not explicitly mapped. VLANs Mapped The list of VLAN's mapped to the MSTI. The VLANs must be separated with comma and/or space. A VLAN can only be mapped to one MSTI. A unused MSTI should just be left empty. (I.e. not having any VLANs mapped to it.
User’s Manual of IGS-604HPT-M12 Figure 4-7-10 : MST1 MSTI Port Configuration Screenshot The page includes the following fields: MSTx MSTI Port Configuration Object Description Port The switch port number of the corresponding STP CIST (and MSTI) port. Path Cost Controls the path cost incurred by the port. The Auto setting will set the path cost as appropriate by the physical link speed, using the 802.1D recommended values. Using the Specific setting, a user-defined value can be entered.
User’s Manual of IGS-604HPT-M12 4.7.8 Port Status This page displays the STP CIST port status for port physical ports in the currently selected switch. The STP Port Status screen in Figure 4-7-11 appears. Figure 4-7-11: STP Port Status Screenshot The page includes the following fields: Object Description Port The switch port number of the logical STP port. CIST Role The current STP port role of the ICST port.
User’s Manual of IGS-604HPT-M12 4.7.9 Port Statistics This page displays the STP port statistics counters for port physical ports in the currently selected switch. The STP Port Statistics screen in Figure 4-7-12 appears. Figure 4-7-12: STP Statistics Screenshot The page includes the following fields: Object Description Port The switch port number of the logical RSTP port. MSTP The number of MSTP Configuration BPDUs received/transmitted on the port.
User’s Manual of IGS-604HPT-M12 4.8 Multicast 4.8.1 IGMP Snooping The Internet Group Management Protocol (IGMP) lets host and routers share information about multicast groups memberships. IGMP snooping is a switch feature that monitors the exchange of IGMP messages and copies them to the CPU for feature processing. The overall purpose of IGMP Snooping is to limit the forwarding of multicast frames to only ports that are a member of the multicast group.
User’s Manual of IGS-604HPT-M12 Figure 4-8-2: Multicast Flooding Figure 4-8-3: IGMP Snooping Multicast Stream Control 155
User’s Manual of IGS-604HPT-M12 IGMP Versions 1 and 2 Multicast groups allow members to join or leave at any time. IGMP provides the method for members and multicast routers to communicate when joining or leaving a multicast group. IGMP version 1 is defined in RFC 1112. It has a fixed packet size and no optional data.
User’s Manual of IGS-604HPT-M12 message, and query messages that are specific to a given group. The states a computer will go through to join or to leave a multicast group are shown below: Figure 4-8-4: IGMP State Transitions IGMP Querier – A router, or multicast-enabled switch, can periodically ask their hosts if they want to receive multicast traffic.
User’s Manual of IGS-604HPT-M12 4.8.2 Profile Table This page provides IPMC Profile related configurations. The IPMC profile is used to deploy the access control on IP multicast streams. It is allowed to create a maximum of 64 Profiles with a maximum of 128 corresponding rules for each. The Profile Table screen in Figure 4-8-5 appears.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add new IPMC profile. Specify the name and configure the new entry. Click "Save”. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.8.3 Address Entry This page provides address range settings used in IPMC profile. The address entry is used to specify the address range that will be associated with IPMC Profile. It is allowed to create a maximum of 128 address entries in the system.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add new address range. Specify the name and configure the addresses. Click "Save”. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. : Refreshes the displayed table starting from the input fields. : Updates the table starting from the first entry in the IPMC Profile Address Configuration. : Updates the table, starting with the entry after the last entry currently displayed. 4.8.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Snooping Enabled Enable the Global IGMP Snooping. Unregistered IPMCv4 Enable unregistered IPMCv4 traffic flooding. Flooding Enabled The flooding control takes effect only when IGMP Snooping is enabled. When IGMP Snooping is disabled, unregistered IPMCv4 traffic flooding is always active in spite of this setting.
User’s Manual of IGS-604HPT-M12 4.8.5 IGMP Snooping VLAN Configuration Each page shows up to 99 entries from the VLAN table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the VLAN Table. The first displayed will be the one with the lowest VLAN ID found in the VLAN Table. The "VLAN" input fields allow the user to select the starting point in the VLAN Table.
User’s Manual of IGS-604HPT-M12 PRI (PRI) Priority of Interface. It indicates the IGMP control frame priority level generated by the system. These values can be used to prioritize different classes of traffic. The allowed range is 0 (best effort) to 7 (highest), default interface priority value is 0 RV Robustness Variable. The Robustness Variable allows tuning for the expected packet loss on a network. The allowed range is 1 to 255, default robustness variable value is 2. QI Query Interval.
User’s Manual of IGS-604HPT-M12 4.8.6 IGMP Snooping Port Group Filtering In certain switch applications, the administrator may want to control the multicast services that are available to end users. For example, an IP/TV service based on a specific subscription plan. The IGMP filtering feature fulfills this requirement by restricting access to specified multicast services on a switch port, and IGMP throttling limits the number of simultaneous multicast groups a port can join.
User’s Manual of IGS-604HPT-M12 4.8.7 IGMP Snooping Status This page provides IGMP Snooping status. The IGMP Snooping Status screen in Figure 4-8-10 appears. Figure 4-8-10: IGMP Snooping Status Screenshot The page includes the following fields: Object Description VLAN ID The VLAN ID of the entry. Querier Version Working Querier Version currently. Host Version Working Host Version currently. Querier Status Show the Querier status is "ACTIVE" or "IDLE".
User’s Manual of IGS-604HPT-M12 Buttons : Click to refresh the page immediately. : Clears all Statistics counters. Auto-refresh : Automatic refresh occurs every 3 seconds. 4.8.8 IGMP Group Information Entries in the IGMP Group Table are shown on this page. The IGMP Group Table is sorted first by VLAN ID, and then by group. Each page shows up to 99 entries from the IGMP Group table, default being 20, selected through the "entries per page" input field.
User’s Manual of IGS-604HPT-M12 4.8.9 IGMPv3 Information Entries in the IGMP SSM Information Table are shown on this page. The IGMP SSM Information Table is sorted first by VLAN ID, then by group, and then by Port No. Diffrent source addresses belong to the same group are treated as single entry. Each page shows up to 99 entries from the IGMP SSM (Source Specific Multicast) Information table, default being 20, selected through the "entries per page" input field.
User’s Manual of IGS-604HPT-M12 4.8.10 MLD Snooping Configuration This page provides MLD Snooping related configuration. The MLD Snooping Configuration screen in Figure 4-8-13 appears. Figure 4-8-13: MLD Snooping Configuration Screenshot The page includes the following fields: Object Description Snooping Enabled Enable the Global MLD Snooping. Unregistered IPMCv6 Enable unregistered IPMCv6 traffic flooding. Flooding enabled The flooding control takes effect only when MLD Snooping is enabled.
User’s Manual of IGS-604HPT-M12 If an aggregation member port is selected as a router port, the whole aggregation will act as a router port. The allowed selection is Auto, Fix, Fone, default compatibility value is Auto. Fast Leave Enable the fast leave on the port. Throtting Enable to limit the number of multicast groups to which a switch port can belong. Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.8.
User’s Manual of IGS-604HPT-M12 network. The allowed selection is MLD-Auto, Forced MLDv1, Forced MLDv2, default compatibility value is MLD-Auto. PRI (PRI) Priority of Interface. It indicates the MLD control frame priority level generated by the system. These values can be used to prioritize different classes of traffic. The allowed range is 0 (best effort) to 7 (highest), default interface priority value is 0 RV Robustness Variable.
User’s Manual of IGS-604HPT-M12 4.8.12 MLD Snooping Port Group Filtering In certain switch applications, the administrator may want to control the multicast services that are available to end users. For example, an IP/TV service based on a specific subscription plan. The MLD filtering feature fulfills this requirement by restricting access to specified multicast services on a switch port, and MLD throttling limits the number of simultaneous multicast groups a port can join.
User’s Manual of IGS-604HPT-M12 4.8.13 MLD Snooping Status This page provides MLD Snooping status. The IGMP Snooping Status screen in Figure 4-8-16 appears. Figure 4-8-16: MLD Snooping Status Screenshot The page includes the following fields: Object Description VLAN ID The VLAN ID of the entry. Querier Version Working Querier Version currently. Host Version Working Host Version currently. Querier Status Shows the Querier status is "ACTIVE" or "IDLE".
User’s Manual of IGS-604HPT-M12 Buttons : Click to refresh the page immediately. : Clears all Statistics counters. Auto-refresh : Automatic refresh occurs every 3 seconds. 4.8.14 MLD Group Information Entries in the MLD Group Table are shown on this page. The MLD Group Table is sorted first by VLAN ID, and then by group.Each page shows up to 99 entries from the MLD Group table, default being 20, selected through the "entries per page" input field.
User’s Manual of IGS-604HPT-M12 4.8.15 MLDv2 Information Entries in the MLD SFM Information Table are shown on this page. The MLD SFM (Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port. Different source addresses belong to the same group are treated as single entry.
User’s Manual of IGS-604HPT-M12 : Updates the table, starting with the entry after the last entry currently displayed. 4.8.16 MVR (Multicast VLAN Registration) The MVR feature enables multicast traffic forwarding on the Multicast VLANs. ■ In a multicast television application, a PC or a network television or a set-top box can receive the multicast stream. ■ Multiple set-top boxes or PCs can be connected to one subscriber port, which is a switch port configured as an MVR receiver port.
User’s Manual of IGS-604HPT-M12 This page provides MVR related configuration. The MVR screen in Figure 4-8-19 appears. Figure 4-8-19: MVR Configuration Screenshot The page includes the following fields: Object Description MVR Mode Enable/Disable the Global MVR. The Unregistered Flooding control depends on the current configuration in IGMP/MLD Snooping. It is suggested to enable Unregistered Flooding control when the MVR group table is full. Delete Check to delete the entry.
User’s Manual of IGS-604HPT-M12 IGMP Address Define the IPv4 address as source address used in IP header for IGMP control frames. The default IGMP address is not set (0.0.0.0). When the IGMP address is not set, system uses IPv4 management address of the IP interface associated with this VLAN. When the IPv4 management address is not set, system uses the first available IPv4 management address. Otherwise, system uses a pre-defined value. By default, this value will be 192.0.2.1.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add new MVR VLAN. Specify the VID and configure the new entry. Click "Save" : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.8.17 MVR Status This page provides MVR status. The MVR Status screen in Figure 4-8-20 appears. Figure 4-8-20: MVR Status Screenshot The page includes the following fields: Object Description VLAN ID The Multicast VLAN ID.
User’s Manual of IGS-604HPT-M12 4.8.18 MVR Groups Information Entries in the MVR Group Table are shown on this page. The MVR Group Table is sorted first by VLAN ID, and then by group. Each page shows up to 99 entries from the MVR Group table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the MVR Group Table.
User’s Manual of IGS-604HPT-M12 4.8.19 MVR SFM Information Entries in the MVR SFM Information Table are shown on this page. The MVR SFM (Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port. Different source addresses belong to the same group are treated as single entry.
User’s Manual of IGS-604HPT-M12 4.9 Quality of Service 4.9.1 Understanding QoS Quality of Service (QoS) is an advanced traffic prioritization feature that allows you to establish control over network traffic. QoS enables you to assign various grades of network service to different types of traffic, such as multi-media, video, protocol-specific, time critical, and file-backup traffic. QoS reduces bandwidth limitations, delay, loss, and jitter.
User’s Manual of IGS-604HPT-M12 4.9.2 Port Policing This page allows you to configure the Policer settings for all switch ports. The Port Policing screen in Figure 4-9-1 appears. Figure 4-9-1: QoS Ingress Port Policers Screenshot The page includes the following fields: Object Description Port The port number for which the configuration below applies. Enable Controls whether the policer is enabled on this switch port. Rate Controls the rate for the policer.
User’s Manual of IGS-604HPT-M12 4.9.3 Port Classification This page allows you to configure the basic QoS Ingress Classification settings for all switch ports. The Port Classification screen in Figure 4-9-2 appears. Figure 4-9-2 : QoS Ingress Port Classification Screenshot The page includes the following fields: Object Description Port The port number for which the configuration below applies. CoS Controls the default class of service. All frames are classified to a CoS.
User’s Manual of IGS-604HPT-M12 All means all ports will have one specific setting. PCP Controls the default PCP value. All frames are classified to a PCP value. If the port is VLAN aware and the frame is tagged, then the frame is classified to the PCP value in the tag. Otherwise the frame is classified to the default PCP value. All means all ports will have one specific setting. DEI Controls the default DEI value. All frames are classified to a DEI value.
User’s Manual of IGS-604HPT-M12 4.9.4 Port Scheduler This page provides an overview of QoS Egress Port Schedulers for all switch ports. The Port Scheduler screen in Figure 4-9-3 appears. Figure 4-9-3: QoS Egress Port Schedule Screenshot The page includes the following fields: Object Description Port The logical port for the settings contained in the same row. Click on the port number in order to configure the schedulers. For more details, please refer to chapter 4.9.5.1.
User’s Manual of IGS-604HPT-M12 4.9.5 Port Shaping This page provides an overview of QoS Egress Port Shapers for all switch ports. The Port Shapping screen in Figure 4-9-4 appears. Figure 4-9-4: QoS Egress Port Shapers Screenshot The page includes the following fields: Object Description Port The logical port for the settings contained in the same row. Click on the port number in order to configure the shapers. For more details, please refer to chapter 4.9.5.1.
User’s Manual of IGS-604HPT-M12 4.9.5.1 QoS Egress Port Schedule and Shapers The Port Scheduler and Shapers for a specific port are configured on this page. The QoS Egress Port Schedule and Shaper screen in Figure 4-9-5 appears. Figure 4-9-5: QoS Egress Port Schedule and Shapers Screenshot The page includes the following fields: Object Description Schedule Mode Controls whether the scheduler mode is "Strict Priority" or "Weighted" on this switch port.
User’s Manual of IGS-604HPT-M12 Queue Shaper Unit Controls the unit of measure for the queue shaper rate as "kbps" or "Mbps". The default value is "kbps". Queue Shaper Excess Controls whether the queue is allowed to use excess bandwidth. Queue Scheduler Controls the weight for this queue. Weight This value is restricted to 1-100. This parameter is only shown if "Scheduler Mode" is set to "Weighted". The default value is "17".
User’s Manual of IGS-604HPT-M12 4.9.6 Port Tag Remarking This page provides an overview of QoS Egress Port Tag Remarking for all switch ports. The Port Tag Remarking screen in Figure 4-9-6 appears. Figure 4-9-6: QoS Egress Port Tag Remarking Screenshot The page includes the following fields: Object Description Port The logical port for the settings contained in the same row. Click on the port number in order to configure tag remarking. For more details, please refer to chapter 4.9.6.1.
User’s Manual of IGS-604HPT-M12 4.9.6.1 QoS Egress Port Tag Remarking The QoS Egress Port Tag Remarking for a specific port are configured on this page. The QoS Egress Port Tag Remarking screen in Figure 4-9-7 appears. Figure 4-9-7: QoS Egress Port Tag Remarking Screenshot The page includes the following fields: Object Description Mode Controls the tag remarking mode for this port. PCP/DEI Configuration (QoS class, DP level) to (PCP, DEI) Mapping ■ Classified: Use classified PCP/DEI values.
User’s Manual of IGS-604HPT-M12 4.9.7 Port DSCP This page allows you to configure the basic QoS Port DSCP Configuration settings for all switch ports. The Port DSCP screen in Figure 4-9-8 appears. Figure 4-9-8: QoS Port DSCP Configuration Screenshot The page includes the following fields: Object Description Port The Port column shows the list of ports for which you can configure dscp ingress and egress settings.
User’s Manual of IGS-604HPT-M12 Egress All: Classify all DSCP. The Configuration All with available options will assign to whole ports. Port Egress Rewriting can be one of –. All means all ports will have one specific setting. Disable: No Egress rewrite. Enable: Rewrite enabled without remapping. Remap DP Unaware: DSCP from analyzer is remapped and frame is remarked with remapped DSCP value. The remapped DSCP value is always taken from the 'DSCP Translation->Egress Remap DP0' table.
User’s Manual of IGS-604HPT-M12 4.9.8 DSCP-based QoS This page allows you to configure the basic QoS DSCP-based QoS Ingress Classification settings for all switches. The DSCP-based QoS screen in Figure 4-9-9 appears. Figure 4-9-9: DSCP-based QoS Ingress Classification Screenshot The page includes the following fields: Object Description DSCP Maximum number of supported DSCP values are 64. Trust Controls whether a specific DSCP value is trusted.
User’s Manual of IGS-604HPT-M12 4.9.9 DSCP Translation This page allows you to configure the basic QoS DSCP Translation settings for all switches. DSCP translation can be done in Ingress or Egress. The DSCP Translation screen in Figure 4-9-10 appears. Figure 4-9-10: DSCP Translation page Screenshot The page includes the following fields: Object Description DSCP Maximum number of supported DSCP values are 64 and valid DSCP value ranges from 0 to 63.
User’s Manual of IGS-604HPT-M12 Translate DSCP at Ingress side can be translated to any of (0-63) DSCP values. Classify Click to enable Classification at Ingress side. Egress There are the following configurable parameters for Egress side – Remap DP0 Controls the remapping for frames with DP level 0. Remap DP1 Controls the remapping for frames with DP level 1. Remap DP0 Select the DSCP value from select menu to which you want to remap. DSCP value ranges from 0 to 63.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description QoS Class Available QoS Class value ranges from 0 to 7. QoS Class (0-7) can be mapped to followed parameters. DPL Actual Drop Precedence Level. DSCP Select DSCP value (0-63) from DSCP menu to map DSCP to corresponding QoS Class and DPL value Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.9.
User’s Manual of IGS-604HPT-M12 ■ Broadcast: Only Broadcast MAC addresses are allowedd. The default value is 'Any'. SMAC Displays the OUI field of Source MAC address, i.e. first three octet (byte) of MAC address. Tag Type Indicates tag type. Possible values are: ■ Any: Match tagged and untagged frames. ■ Untagged: Match untagged frames. ■ Tagged: Match tagged frames. The default value is 'Any' VID Indicates (VLAN ID), either a specific VID or range of VIDs.
User’s Manual of IGS-604HPT-M12 4.9.11.1 QoS Control Entry Configuration The QCE Configuration screen in Figure 4-9-13 appears. Figure 4-9-13: QCE Configuration Screenshot The page includes the following fields: Object Description Port Members Check the checkbox button in case you want to make any port member of the QCL entry. By default all ports will be checked.
User’s Manual of IGS-604HPT-M12 3. LLC 4. SNAP 5. IPv4 6. IPv6 Note: All frame types are explained below. Any Allow all types of frames. EtherType Ethernet Type Valid Ethernet type can have value within 0x600-0xFFFF or 'Any' but excluding 0x800(IPv4) and 0x86DD(IPv6), default value is 'Any'.
User’s Manual of IGS-604HPT-M12 value or 'Any'. DSCP values are in the range of 0-63 including BE, CS1-CS7, EF or AF11-AF43 ■ Sport Source TCP/UDP port:(0-65535) or 'Any', specific or port range applicable for IP protocol UDP/TCP ■ Dport Destination TCP/UDP port:(0-65535) or 'Any', specific or port range applicable for IP protocol UDP/TCP Action Parameters ■ Class QoS class: (0-7) or 'Default'. ■ DPL Valid Drop Precedence Level can be (0-3) or 'Default'.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description User Indicates the QCL user. QCE# Indicates the index of QCE. Port Indicates the list of ports configured with the QCE. Frame Type Indicates the type of frame to look for incoming frames. Possible frame types are: ■ Any: The QCE will match all frame types. ■ Ethernet: Only Ethernet frames (with Ether Type 0x600-0xFFFF) are allowed. Action ■ LLC: Only (LLC) frames are allowed.
User’s Manual of IGS-604HPT-M12 4.9.13 Storm Control Configuration Storm control for the switch is configured on this page. There is a unicast storm rate control, multicast storm rate control, and a broadcast storm rate control. These only affect flooded frames, i.e. frames with a (VLAN ID, DMAC) pair not present on the MAC Address table. The configuration indicates the permitted packet rate for unicast, multicast or broadcast traffic across the switch.
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.9.14 QoS Statistics This page provides statistics for the different queues for all switch ports. The QoS Statistics screen in Figure 4-9-17 appears. Figure 4-9-16: Queuing Counters Screenshot The page includes the following fields: Object Description Port The logical port for the settings contained in the same row.
User’s Manual of IGS-604HPT-M12 4.9.15 Voice VLAN Configuration The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN, then the switch can classify and schedule network traffic. It is recommended that there be two VLANs on a port -- one for voice and one for data. Before connecting the IP device to the switch, the IP phone should configure the voice VLAN ID correctly. It should be configured through its own GUI. The Voice VLAN Configuration screen in Figure 4-9-18 appears.
User’s Manual of IGS-604HPT-M12 Aging Time Indicates the Voice VLAN secure learning age time. The allowed range is 10 to 10000000 seconds. It used when security mode or auto detect mode is enabled. In other cases, it will based hardware age time. The actual age time will be situated in the [age_time; 2 * age_time] interval. Traffic Class Indicates the Voice VLAN traffic class. All traffic on Voice VLAN will apply this class. Mode Indicates the Voice VLAN port mode.
User’s Manual of IGS-604HPT-M12 4.9.16 Voice VLAN OUI Table Configure VOICE VLAN OUI table on this page. The maximum entry number is 16. Modifying the OUI table will restart auto detection of OUI process. The Voice VLAN OUI Table screen in Figure 4-9-18 appears. Figure 4-9-18: Voice VLAN OUI Table Screenshot The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save.
User’s Manual of IGS-604HPT-M12 4.10 Access Control List ACL is an acronym for Access Control List. It is the list table of ACEs, containing access control entries that specify individual users or groups permitted or denied to specific traffic objects, such as a process or a program. Each accessible traffic object contains an identifier to its ACL. The privileges determine whether there are specific traffic object access rights.
User’s Manual of IGS-604HPT-M12 frames. ■ ARP: The ACE will match ARP/RARP frames. ■ IPv4: The ACE will match all IPv4 frames. ■ IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol. ■ IPv4/UDP: The ACE will match IPv4 frames with UDP protocol. ■ IPv4/TCP: The ACE will match IPv4 frames with TCP protocol. ■ IPv4/Other: The ACE will match IPv4 frames, which are not ICMP/UDP/TCP. ■ Action IPv6: The ACE will match all IPv6 standard frames. Indicates the forwarding action of the ACE.
User’s Manual of IGS-604HPT-M12 4.10.2 Access Control List Configuration This page shows the Access Control List (ACL), which is made up of the ACEs defined on this switch. Each row describes the ACE that is defined. The maximum number of ACEs is 512 on each switch. Click on the lowest plus sign to add a new ACE to the list. The reserved ACEs used for internal protocol, cannot be edited or deleted, the order sequence cannot be changed and the priority is highest.
User’s Manual of IGS-604HPT-M12 Disabled is displayed, the rate limiter operation is disabled. Port Redirect Indicates the port redirect operation of the ACE. Frames matching the ACE are redirected to the port number. The allowed values are Disabled or a specific port number. When Disabled is displayed, the port redirect operation is disabled. Mirror Specify the mirror operation of this port. Frames matching the ACE are mirrored to the destination mirror port.
User’s Manual of IGS-604HPT-M12 4.10.3 ACE Configuration Configure an ACE (Access Control Entry) on this page. An ACE consists of several parameters. These parameters vary according to the frame type that you select. First select the ingress port for the ACE, and then select the frame type. Different parameter options are displayed depending on the frame type selected. A frame that hits this ACE matches the configuration that is defined here. The ACE Configuration screen in Figure 4-10-3 appears.
User’s Manual of IGS-604HPT-M12 The allowed range is 0x0 to 0xff. Frame Type Select the frame type for this ACE. These frame types are mutually exclusive. ■ Any: Any frame can match this ACE. ■ Ethernet Type: Only Ethernet Type frames can match this ACE. The IEEE 802.3 describes the value of Length/Type Field specifications to be greater than or equal to 1536 decimal (equal to 0600 hexadecimal). ■ ARP: Only ARP frames can match this ACE. Notice the ARP frames won't match the ACE with Ethernet type.
User’s Manual of IGS-604HPT-M12 Note: The shutdown feature only works when the packet length is less than 1518(without VLAN tags). Counter The counter indicates the number of times the ACE was hit by a frame. MAC Parameters Object Description SMAC Filter (Only displayed when the frame type is Ethernet Type or ARP.) Specify the source MAC filter for this ACE. ■ Any: No SMAC filter is specified. (SMAC filter status is "don't-care".
User’s Manual of IGS-604HPT-M12 ■ Specific: If you want to filter a specific VLAN ID with this ACE, choose this value. A field for entering a VLAN ID number appears. VLAN ID When "Specific" is selected for the VLAN ID filter, you can enter a specific VLAN ID number. The allowed range is 1 to 4095. A frame that hits this ACE matches this VLAN ID value. Tag Priority Specify the tag priority for this ACE. A frame that hits this ACE matches this tag priority. The allowed number range is 0 to 7.
User’s Manual of IGS-604HPT-M12 appear. Target IP Address When "Host" or "Network" is selected for the target IP filter, you can enter a specific target IP address in dotted decimal notation. Target IP Mask When "Network" is selected for the target IP filter, you can enter a specific target IP mask in dotted decimal notation.
User’s Manual of IGS-604HPT-M12 ■ Any: No IP protocol filter is specified ("don't-care"). ■ Specific: If you want to filter a specific IP protocol filter with this ACE, choose this value. A field for entering an IP protocol filter appears. ■ ICMP: Select ICMP to filter IPv4 ICMP protocol frames. Extra fields for defining ICMP parameters will appear. These fields are explained later in this help file. ■ UDP: Select UDP to filter IPv4 UDP protocol frames.
User’s Manual of IGS-604HPT-M12 ■ Network: Source IP filter is set to Network. Specify the source IP address and source IP mask in the SIP Address and SIP Mask fields that appear. SIP Address When "Host" or "Network" is selected for the source IP filter, you can enter a specific SIP address in dotted decimal notation. SIP Mask When "Network" is selected for the source IP filter, you can enter a specific SIP mask in dotted decimal notation.
User’s Manual of IGS-604HPT-M12 SIP Filter Specify the source IPv6 filter for this ACE. ■ Any: No source IPv6 filter is specified. (Source IPv6 filter is "don't-care".) ■ Specific: Source IPv6 filter is set to Network. Specify the source IPv6 address and source IPv6 mask in the SIP Address fields that appear. SIP Address When "Specific" is selected for the source IPv6 filter, you can enter a specific SIPv6 address. The field only supported last 32 bits for IPv6 address.
User’s Manual of IGS-604HPT-M12 ICMP code value. The allowed range is 0 to 255. A frame that hits this ACE matches this ICMP code value. TCP/UDP Parameters Object Description TCP/UDP Source Filter Specify the TCP/UDP source filter for this ACE. ■ Any: No TCP/UDP source filter is specified (TCP/UDP source filter status is "don't-care"). ■ Specific: If you want to filter a specific TCP/UDP source filter with this ACE, you can enter a specific TCP/UDP source value.
User’s Manual of IGS-604HPT-M12 entry. TCP SYN ■ 1: TCP frames where the FIN field is set must be able to match this entry. ■ Any: Any value is allowed ("don't-care"). Specify the TCP "Synchronize sequence numbers" (SYN) value for this ACE. ■ 0: TCP frames where the SYN field is set must not be able to match this entry. TCP RST ■ 1: TCP frames where the SYN field is set must be able to match this entry. ■ Any: Any value is allowed ("don't-care").
User’s Manual of IGS-604HPT-M12 Ethernet Type Value When "Specific" is selected for the EtherType filter, you can enter a specific EtherType value. The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6). A frame that hits this ACE matches this EtherType value. Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. : Return to the previous page. 4.10.
User’s Manual of IGS-604HPT-M12 EVC Policer Select whether EVC policer is enabled or disabled. The default value is "Disabled". Note that ACL rate limiter and EVC policer can not both be enabled. EVC Policer ID Select which EVC policer ID to apply on this port. The allowed values are Disabled or the values 1 through 256. Port Redirect Select which port frames are redirected on. The allowed values are Disabled or a specific port number and it can't be set when action is permitted.
User’s Manual of IGS-604HPT-M12 4.10.5 ACL Rate Limiter Configuration Configure the rate limiter for the ACL of the switch. The ACL Rate Limiter Configuration screen in Figure 4-10-5 appears. Figure 4-10-5: ACL Rate Limiter Configuration Screenshot The page includes the following fields: Object Description Rate Limiter ID The rate limiter ID for the settings contained in the same row. Rate (pps) The allowed values are: 0-3276700 in pps or 0, 100, 200, 300, ..., 1000000 in kbps.
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.11 Authentication This section is to control the access of the Industrial Managed Switch, including the user access and management control. The Authentication section contains links to the following main topics: IEEE 802.1X Port-based Network Access Control MAC-based Authentication User Authentication Overview of 802.
User’s Manual of IGS-604HPT-M12 forwarded on the switch. There are no EAPOL frames involved in this authentication, and therefore, MAC-based Authentication has nothing to do with the 802.1X standard. The advantage of MAC-based authentication over 802.1X is that several clients can be connected to the same port (e.g. through a 3rd party switch or a hub) and still require individual authentication, and that the clients don't need special supplicant software to authenticate.
User’s Manual of IGS-604HPT-M12 Device Roles With 802.1X port-based authentication, the devices in the network have specific roles as shown below. Figure 4-11-1 Client—the device (workstation) that requests access to the LAN and switch services and responds to requests from the switch. The workstation must be running 802.1X-compliant client software such as that offered in the Microsoft Windows XP operating system. (The client is the supplicant in the IEEE 802.1X specification.
User’s Manual of IGS-604HPT-M12 frames and relays them to the authentication server, the Ethernet header is stripped and the remaining EAP frame is re-encapsulated in the RADIUS format. The EAP frames are not modified or examined during encapsulation, and the authentication server must support EAP within the native frame format.
User’s Manual of IGS-604HPT-M12 Figure 4-11-2: EAP Message Exchange Ports in Authorized and Unauthorized States The switch port state determines whether or not the client is granted access to the network. The port starts in the unauthorized state. While in this state, the port disallows all ingress and egress traffic except for 802.1X protocol packets. When a client is successfully authenticated, the port transitions to the authorized state, allowing all traffic for the client to flow normally.
User’s Manual of IGS-604HPT-M12 4.11.2 Authentication Configuration This page allows you to configure how a user is authenticated when he logs into the switch via one of the management client interfaces. The Authentication Method Configuration screen in Figure 4-11-3 appears.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Client The management client for which the configuration below applies. Authentication Method Authentication Method can be set to one of the following values: ■ None: authentication is disabled and login is not possible. ■ Local: use the local user database on the switch stack for authentication. ■ RADIUS: use a remote RADIUS server for authentication.
User’s Manual of IGS-604HPT-M12 Figure 4-11-4: Network Access Server Configuration Screenshot The page includes the following fields: System Configuration Object Description Mode Indicates if NAS is globally enabled or disabled on the switch. If globally disabled, all ports are allowed forwarding of frames. Reauthentication Enabled If checked, successfully authenticated supplicants/clients are reauthenticated after the interval specified by the Reauthentication Period. Reauthentication for 802.
User’s Manual of IGS-604HPT-M12 Reauthentication Period Determines the period, in seconds, after which a connected client must be reauthenticated. This is only active if the Reauthentication Enabled checkbox is checked. Valid values are in the range 1 to 3600 seconds. EAPOL Timeout Determines the time for retransmission of Request Identity EAPOL frames. Valid values are in the range 1 to 65535 seconds. This has no effect for MAC-based ports.
User’s Manual of IGS-604HPT-M12 The Hold Time can be set to a number between 10 and 1000000 seconds. RADIUS-Assigned QoS Enabled RADIUS-assigned QoS provides a means to centrally control the traffic class to which traffic coming from a successfully authenticated supplicant is assigned on the switch. The RADIUS server must be configured to transmit special RADIUS attributes to take advantage of this feature.
User’s Manual of IGS-604HPT-M12 enabled. Valid values are in the range [1; 255]. Allow Guest VLAN if EAPOL Seen The switch remembers if an EAPOL frame has been received on the port for the life-time of the port. Once the switch considers whether to enter the Guest VLAN, it will first check if this option is enabled or disabled. If disabled (unchecked; default), the switch will only enter the Guest VLAN if an EAPOL frame has not been received on the port for the life-time of the port.
User’s Manual of IGS-604HPT-M12 sent between the switch and the RADIUS server are RADIUS packets. RADIUS packets also encapsulate EAP PDUs together with other attributes like the switch's IP address, name, and the supplicant's port number on the switch. EAP is very flexible, in that it allows for different authentication methods, like MD5-Challenge, PEAP, and TLS.
User’s Manual of IGS-604HPT-M12 credentials within a certain amount of time, another supplicant will get a chance. Once a supplicant is successfully authenticated, only that supplicant will be allowed access. This is the most secure of all the supported modes. In this mode, the Port Security module is used to secure a supplicant's MAC address once successfully authenticated. Multi 802.1X Multi 802.1X is - like Single 802.
User’s Manual of IGS-604HPT-M12 particular client, using the Port Security module. Only then will frames from the client be forwarded on the switch. There are no EAPOL frames involved in this authentication, and therefore, MAC-based Authentication has nothing to do with the 802.1X standard. The advantage of MAC-based authentication over port-based 802.1X is that several clients can be connected to the same port (e.g.
User’s Manual of IGS-604HPT-M12 in the range [0; 7]. RADIUS-Assigned When RADIUS-Assigned VLAN is both globally enabled and enabled (checked) VLAN Enabled for a given port, the switch reacts to VLAN ID information carried in the RADIUS Access-Accept packet transmitted by the RADIUS server when a supplicant is successfully authenticated.
User’s Manual of IGS-604HPT-M12 Guest VLAN Enabled When Guest VLAN is both globally enabled and enabled (checked) for a given port, the switch considers moving the port into the Guest VLAN according to the rules outlined below. This option is only available for EAPOL-based modes, i.e.: Port-based 802.1X Single 802.1X Multi 802.1X For troubleshooting VLAN assignments, use the "Monitor→VLANs→VLAN Membership and VLAN Port" pages.
User’s Manual of IGS-604HPT-M12 ■ Unauthorized: The port is in Force Unauthorized or a single-supplicant mode and the supplicant is not successfully authorized by the RADIUS server. ■ X Auth/Y Unauth: The port is in a multi-supplicant mode. Currently X clients are authorized and Y are unauthorized. Restart Two buttons are available for each row. The buttons are only enabled when authentication is globally enabled and the port's Admin State is in an EAPOL-based or MAC-based mode.
User’s Manual of IGS-604HPT-M12 4.11.4 Network Access Overview This page provides an overview of the current NAS port states for the selected switch. The Network Access Overview screen in Figure 4-11-5 appears. Figure 4-11-5: Network Access Server Switch Status Screenshot The page includes the following fields: Object Description Port The switch port number. Click to navigate to detailed NAS statistics for this port. Admin State The port's current administrative state.
User’s Manual of IGS-604HPT-M12 Buttons : Click to refresh the page immediately. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. 4.11.5 Network Access Statistics This page provides detailed NAS statistics for a specific switch port running EAPOL-based IEEE 802.1X authentication. For MAC-based ports, it shows selected backend server (RADIUS Authentication Server) statistics only.
User’s Manual of IGS-604HPT-M12 Port Counters Object Description EAPOL Counters These supplicant frame counters are available for the following administrative states: ■ Force Authorized ■ Force Unauthorized ■ Port-based 802.1X ■ Single 802.1X ■ Multi 802.1X Direction Name IEEE Name Description Rx Total dot1xAuthEapolFrames The number of valid EAPOL Rx frames of any type that have been received by the switch.
User’s Manual of IGS-604HPT-M12 received by the switch in which the Packet Body Length field is invalid. Tx Total dot1xAuthEapolFrames The number of EAPOL Tx frames of any type that have been transmitted by the switch. Tx Request ID dot1xAuthEapolReqIdFr The number of EAPOL amesTx Request Identity frames that have been transmitted by the switch.
User’s Manual of IGS-604HPT-M12 table) or client (right-most table). Rx Other dot1xAuthBackendOther 802.1X-based: Requests RequestsToSupplicant Counts the number of times that the switch sends an EAP Request packet following the first to the supplicant. Indicates that the backend server chose an EAP-method. MAC-based: Not applicable. Rx Auth. dot1xAuthBackendAuth 802.1X- and MAC-based: Successes Successes Counts the number of times that the switch receives a success indication.
User’s Manual of IGS-604HPT-M12 Counts all the backend server packets sent from the switch towards the backend server for a given port (left-most table) or client (right-most table). Possible retransmissions are not counted. Last Supplicant/Client Info Information about the last supplicant/client that attempted to authenticate. This information is available for the following administrative states: ■ Port-based 802.1X ■ Single 802.1X ■ Multi 802.1X ■ MAC-based Auth.
User’s Manual of IGS-604HPT-M12 ■ MAC-based Auth. The table is identical to and is placed next to the Port Counters table, and will be empty if no MAC address is currently selected. To populate the table, select one of the attached MAC Addresses from the table below. Attached MAC Address Object Description Identity Shows the identity of the supplicant, as received in the Response Identity EAPOL frame.
User’s Manual of IGS-604HPT-M12 • Port-based 802.1X • Single 802.1X Click to clear the counters for the selected port. : This button is available in the following modes: • Multi 802.1X • MAC-based Auth.X Click to clear both the port counters and all of the attached client's counters. The "Last Client" will not be cleared, however. : This button is available in the following modes: • Multi 802.1X • MAC-based Auth.X Click to clear only the currently selected client's counters.
User’s Manual of IGS-604HPT-M12 4.11.6 RADIUS This page allows you to configure the RADIUS Servers. The RADIUS Configuration screen in Figure 4-11-7 appears. Figure 4-11-7: RADIUS Server Configuration Screenshot The page includes the following fields: Global Configuration These settings are common for all of the RADIUS Servers. Object Description Timeout Timeout is the number of seconds, in the range 1 to 1000, to wait for a reply from a RADIUS server before retransmitting the request.
User’s Manual of IGS-604HPT-M12 more than one server has been configured. Key The secret key -- up to 63 characters long -- shared between the RADIUS server and the switch. NAS-IP-Address The IPv4 address to be used as attribute 4 in RADIUS Access-Request packets. If this field is left blank, the IP address of the outgoing interface is used. NAS-IPv6-Address The IPv6 address to be used as attribute 95 in RADIUS Access-Request packets.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add a new RADIUS server. An empty row is added to the table, and the RADIUS server can be configured as needed. Up to 5 servers are supported. : Click to undo the addition of the new server. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.11.7 TACACS+ This page allows you to configure the TACACS+ Servers. The TACACS+ Configuration screen in Figure 4-11-8 appears.
User’s Manual of IGS-604HPT-M12 Setting the Deadtime to a value greater than 0 (zero) will enable this feature, but only if more than one server has been configured. Key The secret key - up to 63 characters long - shared between the TACACS+ server and the switch. Server Configuration The table has one row for each TACACS+ server and a number of columns, which are: Object Description Delete To delete a TACACS+ server entry, check this box. The entry will be deleted during the next Save.
User’s Manual of IGS-604HPT-M12 4.11.8 RADIUS Overview This page provides an overview of the status of the RADIUS servers configurable on the Authentication configuration page. The RADIUS Authentication/Accounting Server Overview screen in Figure 4-11-9 appears. Figure 4-11-9: RADIUS Authentication/Accounting Server Overview Screenshot The page includes the following fields: RADIUS Authentication Server Status Overview Object Description # The RADIUS server number.
User’s Manual of IGS-604HPT-M12 RADIUS Accounting Server Status Overview Object Description # The RADIUS server number. Click to navigate to detailed statistics for this server. IP Address The IP address and UDP port number (in : notation) of this server. Status The current state of the server. This field takes one of the following values: Disabled: The server is disabled. Not Ready: The server is enabled, but IP communication is not yet up and running.
User’s Manual of IGS-604HPT-M12 4.11.9 RADIUS Details This page provides detailed statistics for a particular RADIUS server. The RADIUS Authentication/Accounting for Server Overview screen in Figure 4-11-10 appears. Figure 4-11-10: RADIUS Authentication/Accounting for Server Overview Screenshot The page includes the following fields: RADIUS Authentication Statistics The statistics map closely to those specified in RFC4668 -- RADIUS Authentication Client MIB.
User’s Manual of IGS-604HPT-M12 Direction Name RFC4668 Name Description Rx Access radiusAuthClientExtA The number of RADIUS Accepts ccessAccepts Access-Accept packets (valid or invalid) received from the server. Rx Access Rejects radiusAuthClientExtA The number of RADIUS ccessRejects Access-Reject packets (valid or invalid) received from the server.
User’s Manual of IGS-604HPT-M12 Rx Packets radiusAuthClientExtP The number of RADIUS Dropped acketsDropped packets that were received from the server on the authentication port and dropped for some other reason. Tx Access radiusAuthClientExtA The number of RADIUS Requests ccessRequests Access-Request packets sent to the server. This does not include retransmissions.
User’s Manual of IGS-604HPT-M12 Other Info This section contains information about the state of the server and the latest round-trip time. Name RFC4668 Name Description IP Address - IP address and UDP port for the authentication server in question. State - Shows the state of the server. It takes one of the following values: Disabled: The selected server is disabled. Not Ready: The server is enabled, but IP communication is not yet up and running.
User’s Manual of IGS-604HPT-M12 Rx Responses radiusAccClientExt The number of RADIUS Responses packets (valid or invalid) received from the server. Rx Malformed radiusAccClientExt The number of malformed Responses MalformedRespons RADIUS packets received es from the server. Malformed packets include packets with an invalid length. Bad authenticators or or unknown types are not included as malformed access responses.
User’s Manual of IGS-604HPT-M12 variable is incremented when a Request is sent and decremented due to receipt of a Response, timeout, or retransmission. Tx Timeouts radiusAccClientExt The number of accounting Timeouts timeouts to the server. After a timeout, the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.
User’s Manual of IGS-604HPT-M12 when more than one server is enabled. Round-Trip radiusAccClientExtRo Time undTripTime The time interval (measured in milliseconds) between the most recent Response and the Request that matched it from the RADIUS accounting server. The granularity of this measurement is 100 ms. A value of 0 ms indicates that there hasn't been round-trip communication with the server yet. Buttons Auto-refresh : Check this box to refresh the page automatically.
User’s Manual of IGS-604HPT-M12 4.11.10 Windows Platform RADIUS Server Configuration Set up the RADIUS server and assign the client IP address to the Industrial Managed Switch. In this case, field in the default IP address of the Industrial Managed Switch with 192.168.0.100. And also make sure the shared secret key is the same as the one you have set at the Industrial Managed Switch’s 802.1x system configuration – 12345678 in this case. 1. Configure the IP address of remote RADIUS server and secret key.
User’s Manual of IGS-604HPT-M12 2. Add New RADIUS Client to the Windows 2003 server Figure 4-11-12: Windows Server – Add New RADIUS Client Setting 3.
User’s Manual of IGS-604HPT-M12 4. The shared secret key should be the same as the key configured on the Industrial Managed Switch. Figure 4-11-14: Windows Server RADIUS Server Setting 5. Configure ports attribute of 802.1X the same as “802.1X Port Configuration”. Figure 4-11-15: 802.
User’s Manual of IGS-604HPT-M12 6. Create user data. The establishment of the user data needs to be created on the Radius Server PC.
User’s Manual of IGS-604HPT-M12 7.
User’s Manual of IGS-604HPT-M12 Set the Port Authenticate Status to “Force Authorized” if the port is connected to the RADIUS server or the port is an uplink port that is connected to another switch. Or once the 802.1X starts to work, the switch might not be able to access the RADIUS server. 4.11.11 802.1X Client Configuration Windows XP is originally 802.1X support. As to other operating systems (windows 98SE, ME, 2000), an 802.1X client utility is needed.
User’s Manual of IGS-604HPT-M12 4. Select “Authentication” tab. 5. Select “Enable network access control using IEEE 802.1X” to enable 802.1x authentication. 6. Select “MD-5 Challenge” from the drop-down list box for EAP type. Figure 4-11-20 7. Click “OK”. 8. When client has associated with the Industrial Managed Switch, a user authentication notice appears in system tray. Click on the notice to continue.
User’s Manual of IGS-604HPT-M12 9. Enter the user name, password and the logon domain that your account belongs. 10. Click “OK” to complete the validation process.
User’s Manual of IGS-604HPT-M12 4.12 Security This section is to control the access of the Industrial Managed Switch, and includes the user access and management control. The Security page contains links to the following main topics: Port Limit Control Access Management HTTPs/SSH DHCP Snooping IP Source Guard ARP Inspection 4.12.1 Port Limit Control This page allows you to configure the Port Security Limit Control system and port settings.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: System Configuration Object Description Mode Indicates if Limit Control is globally enabled or disabled on the switchstack. If globally disabled, other modules may still use the underlying functionality, but limit checks and corresponding actions are disabled. Aging Enabled If checked, secured MAC addresses are subject to aging as discussed under Aging Period.
User’s Manual of IGS-604HPT-M12 Control on a given port. Limit The maximum number of MAC addresses that can be secured on this port. This number cannot exceed 1024. If the limit is exceeded, the corresponding action is taken. The switch is "born" with a total number of MAC addresses from which all ports draw whenever a new MAC address is seen on a Port Security-enabled port.
User’s Manual of IGS-604HPT-M12 Shutdown. Re-open Button If a port is shutdown by this module, you may reopen it by clicking this button, which will only be enabled if this is the case. For other methods, refer to Shutdown in the Action section. Note, that clicking the reopen button causes the page to be refreshed, so non-committed changes will be lost. Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. : Click to refresh the page.
User’s Manual of IGS-604HPT-M12 4.12.2 Access Management Configure access management table on this page. The maximum entry number is 16. If the application's type matches any one of the access management entries, it will allow access to the switch. The Access Management Configuration screen in Figure 4-12-2 appears. Figure 4-12-2: Access Management Configuration Overview Screenshot The page includes the following fields: Object Description Mode Indicates the access management mode operation.
User’s Manual of IGS-604HPT-M12 4.12.3 Access Management Statistics This page provides statistics for access management. The Access Management Statistics screen in Figure 4-12-3 appears. Figure 4-12-3: Access Management Statistics Overview Screenshot The page includes the following fields: Object Description Interface The interface that allowed remote host can access the switch. Receive Packets The received packets number from the interface under access management mode is enabled.
User’s Manual of IGS-604HPT-M12 4.12.4 HTTPs Configure HTTPS on this page. The HTTPS Configuration screen in Figure 4-12-4 appears. Figure 4-12-4: HTTPS Configuration Screen Screenshot The page includes the following fields: Object Description Mode Indicates the HTTPS mode operation. When the current connection is HTTPS, to apply HTTPS disabled mode operation will automatically redirect web browser to an HTTP connection.
User’s Manual of IGS-604HPT-M12 4.12.5 SSH Configure SSH on this page. This page shows the Port Security status. Port Security is a module with no direct configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for software-based learning.
User’s Manual of IGS-604HPT-M12 The status page is divided into two sections - one with a legend of user modules and one with the actual port status. The Port Security Status screen in Figure 4-12-6 appears. Figure 4-12-6: Port Security Status Screen Screenshot The page includes the following fields: User Module Legend The legend shows all user modules that may request Port Security services. Object Description User Module Name The full name of a module that may request Port Security services.
User’s Manual of IGS-604HPT-M12 not enabled, whereas a letter indicates that the user module abbreviated by that letter has enabled port security. State Shows the current state of the port. It can take one of four values: Disabled: No user modules are currently using the Port Security service. Ready: The Port Security service is in use by at least one user module, and is awaiting frames from unknown MAC addresses to arrive.
User’s Manual of IGS-604HPT-M12 4.12.7 Port Security Detail This page shows the MAC addresses secured by the Port Security module. Port Security is a module with no direct configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for software-based learning.
User’s Manual of IGS-604HPT-M12 4.12.8 DHCP Snooping DHCP Snooping is used to block intruder on the untrusted ports of DUT when it tries to intervene by injecting a bogus DHCP reply packet to a legitimate conversation between the DHCP client and server. Configure DHCP Snooping on this page. The DHCP Snooping Configuration screen in Figure 4-12-8 appears.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Snooping Mode Indicates the DHCP snooping mode operation. Possible modes are: Enabled: Enable DHCP snooping mode operation. When enable DHCP snooping mode operation, the request DHCP messages will be forwarded to trusted ports and only allowed reply packets from trusted ports. Disabled: Disable DHCP snooping mode operation. Port Mode Indicates the DHCP snooping port mode.
User’s Manual of IGS-604HPT-M12 : To start over 4.12.10 IP Source Guard Configuration IP Source Guard is a secure feature used to restrict IP traffic on DHCP snooping untrusted ports by filtering traffic based on the DHCP Snooping Table or manually configured IP Source Bindings. It helps prevent IP spoofing attacks when a host tries to spoof and use the IP address of another host. This page provides IP Source Guard related configuration. The IP Source Guard Configuration screen in Figure 4-12-10 appears.
User’s Manual of IGS-604HPT-M12 that are matched in static entries on the specific port. Buttons : Click to translate all dynamic entries to static entries. : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.12.11 IP Source Guard Static Table This page provides Static IP Source Guard Table. The Static IP Source Guard Table screen in Figure 4-12-11 appears.
User’s Manual of IGS-604HPT-M12 4.12.12 Dynamic IP Source Guard Table Entries in the Dynamic IP Source Guard Table are shown on this page. The Dynamic IP Source Guard Table is sorted first by port, then by VLAN ID, then by IP address, and then by IP mask. The Dynamic IP Source Guard Table screen in Figure 4-12-12 appears.
User’s Manual of IGS-604HPT-M12 Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Refreshes the displayed table starting from the "Start from MAC address" and "VLAN" input fields. : Flushes all dynamic entries. 4.12.13 ARP Inspection ARP Inspection is a secure feature. Several types of attacks can be launched against a host or devices connected to Layer 2 networks by "poisoning" the ARP caches.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Mode of ARP Inspection Enable the Global ARP Inspection or disable the Global ARP Inspection. Configuration Port Mode Configuration Specify ARP Inspection is enabled on which ports. Only when both Global Mode and Port Mode on a given port are enabled, ARP Inspection is enabled on this given port. Possible modes are: Enabled: Enable ARP Inspection operation. Disabled: Disable ARP Inspection operation.
User’s Manual of IGS-604HPT-M12 4.12.14 ARP Inspection Static Table This page provides Static ARP Inspection Table. The Static ARP Inspection Table screen in Figure 4-12-14 appears. Figure 4-12-14: Static ARP Inspection Table Screen Screenshot The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. Port The logical port for the settings. VLAN ID The VLAN ID for the settings.
User’s Manual of IGS-604HPT-M12 4.12.15 Dynamic ARP Inspection Table Entries in the Dynamic ARP Inspection Table are shown on this page. The Dynamic ARP Inspection Table contains up to 1024 entries, and is sorted first by port, then by VLAN ID, then by MAC address, and then by IP address. The Dynamic ARP Inspection Table screen in Figure 4-12-15 appears.
User’s Manual of IGS-604HPT-M12 : Updates the table starting from the first entry in the MAC Table, i.e. the entry with the lowest VLAN ID and MAC address. : Updates the table, starting with the entry after the last entry currently displayed.
User’s Manual of IGS-604HPT-M12 4.13 MAC Address Table Switching of frames is based upon the DMAC address contained in the frame. The Industrial Managed Switch builds up a table that maps MAC addresses to switch ports for knowing which ports the frames should go to (based upon the DMAC address in the frame ). This table contains both static and dynamic entries.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Aging Configuration By default, dynamic entries are removed from the MAC table after 300 seconds. This removal is also called aging. Object Description Disable Automatic Enables/disables the the automatic aging of dynamic entries Aging Aging Time The time after which a learned entry is discarded. By default, dynamic entries are removed from the MAC after 300 seconds. This removal is also called aging.
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.13.2 MAC Address Table Status Dynamic MAC Table Entries in the MAC Table are shown on this page. The MAC Table contains up to 8192 entries, and is sorted first by VLAN ID, then by MAC address. The MAC Address Table screen in Figure 4-13-2 appears.
User’s Manual of IGS-604HPT-M12 The “>>” will use the last entry of the currently displayed VLAN/MAC address pairs as a basis for the next lookup. When the end is reached the text "no more entries" is shown in the displayed table. Use the “|<<” button to start over. The page includes the following fields: Object Description Type Indicates whether the entry is a static or dynamic entry. VLAN The VLAN ID of the entry. MAC Address The MAC address of the entry.
User’s Manual of IGS-604HPT-M12 4.14 LLDP 4.14.1 Link Layer Discovery Protocol Link Layer Discovery Protocol (LLDP) is used to discover basic information about neighboring devices on the local broadcast domain. LLDP is a Layer 2 protocol that uses periodic broadcasts to advertise information about the sending device. Advertised information is represented in Type Length Value (TLV) format according to the IEEE 802.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: LLDP Parameters Object Description Tx Interval The switch is periodically transmitting LLDP frames to its neighbors for having the network discovery information up-to-date. The interval between each LLDP frame is determined by the Tx Interval value. Valid values are restricted to 5 32768 seconds.
User’s Manual of IGS-604HPT-M12 Tx only The switch will drop LLDP information received from neighbors, but will send out LLDP information. Disabled The switch will not send out LLDP information, and will drop LLDP information received from neighbors. Enabled The switch will send out LLDP information, and will analyze LLDP information received from neighbors. CDP Aware Select CDP awareness. The CDP operation is restricted to decoding incoming CDP frames (The switch doesn't transmit CDP frames).
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.14.3 LLDP MED Configuration This page allows you to configure the LLDP-MED. The LLDPMED Configuration screen in Figure 4-14-2 appears.
User’s Manual of IGS-604HPT-M12 limited LLDPU space and to reduce security and system integrity issues that can come with inappropriate knowledge of the network policy. With this in mind LLDP-MED defines an LLDP-MED Fast Start interaction between the protocol and the application layers on top of the protocol, in order to achieve these related properties. Initially, a Network Connectivity Device will only transmit LLDP TLVs in an LLDPDU.
User’s Manual of IGS-604HPT-M12 It is possible to select between two altitude types (floors or meters). Meters: Representing meters of Altitude defined by the vertical datum specified. Floors: Representing altitude in a form more relevant in buildings which have different floor-to-floor dimensions. An altitude = 0.0 is meaningful even outside a building, and represents ground level at the given latitude and longitude. Inside a building, 0.
User’s Manual of IGS-604HPT-M12 House no. House number, for example, 21 House no.
User’s Manual of IGS-604HPT-M12 The network policy attributes advertised are: 1. Layer 2 VLAN ID (IEEE 802.1Q-2003) 2. Layer 2 priority value (IEEE 802.1D-2004) 3. Layer 3 Diffserv code point (DSCP) value (IETF RFC 2474) This network policy is potentially advertised and associated with multiple sets of application types supported on a given port. The application types specifically addressed are: 1. Voice 2. Guest Voice 3. Softphone Voice 4. Video Conferencing 5. Streaming Video 6.
User’s Manual of IGS-604HPT-M12 guest users and visitors with their own IP Telephony handsets and other similar appliances supporting interactive voice services. Guest Voice Signaling (conditional) - for use in network topologies that require a different policy for the guest voice signaling than for the guest voice media. This application type should not be advertised if all the same network policies apply as those advertised in the Guest Voice application policy.
User’s Manual of IGS-604HPT-M12 VLAN ID VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003 L2 Priority L2 Priority is the Layer 2 priority to be used for the specified application type. L2 Priority may specify one of eight priority levels (0 through 7), as defined by IEEE 802.1D-2004. A value of 0 represents use of the default priority as defined in IEEE 802.1D-2004.
User’s Manual of IGS-604HPT-M12 4.14.4 LLDP-MED Neighbor This page provides a status overview for all LLDP-MED neighbors. The displayed table contains a row for each port on which an LLDP neighbor is detected. The LLDP-MED Neighbor Information screen in Figure 4-14-3 appears.
User’s Manual of IGS-604HPT-M12 defined for the previous Endpoint Device Class. Fore-example will any LLDP-MED Endpoint Device claiming compliance as a Media Endpoint (Class II) also support all aspects of TIA-1057 applicable to Generic Endpoints (Class I), and any LLDP-MED Endpoint Device claiming compliance as a Communication Device (Class III) will also support all aspects of TIA-1057 applicable to both Media Endpoints (Class II) and Generic Endpoints (Class I).
User’s Manual of IGS-604HPT-M12 1. LLDP-MED capabilities 2. Network Policy 3. Location Identification 4. Extended Power via MDI - PSE 5. Extended Power via MDI - PD 6. Inventory 7. Reserved Application Type Application Type indicating the primary function of the application(s) defined for this network policy, advertised by an Endpoint or Network Connectivity Device. The poosible application types are shown below.
User’s Manual of IGS-604HPT-M12 TAG TAG is indicating whether the specified application type is using a tagged or an untagged VLAN. Can be Tagged ot Untagged Untagged: The device is using an untagged frame format and as such does not include a tag header as defined by IEEE 802.1Q-2003. Tagged: The device is using the IEEE 802.1Q tagged frame format VLAN ID VLAN ID is the VLAN identifier (VID) for the port as defined in IEEE 802.1Q-2003.
User’s Manual of IGS-604HPT-M12 4.14.5 Neighbor This page provides a status overview for all LLDP neighbors. The displayed table contains a row for each port on which an LLDP neighbor is detected. The LLDP Neighbor Information screen in Figure 4-14-4 appears. Figure 4-14-4: LLDP Neighbor Information Screenshot The page includes the following fields: Object Description Local Port The port on which the LLDP frame was received.
User’s Manual of IGS-604HPT-M12 Buttons : Click to refresh the page immediately. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. 4.14.6 Port Statistics This page provides an overview of all LLDP traffic. Two types of counters are shown. Global counters are counters that refer to the whole stack, switch, while local counters refers to counters for the currently selected switch. The LLDP Statistics screen in Figure 4-14-5 appears.
User’s Manual of IGS-604HPT-M12 Entries Dropped Total Neighbors Shows the number of entries deleted due to Time-To-Live expiring. Entries Aged Out LLDP Statistics Local Counters The displayed table contains a row for each port. The columns hold the following information: Object Description Local Port The port on which LLDP frames are received or transmitted. Tx Frames The number of LLDP frames transmitted on the port. Rx Frames The number of LLDP frames received on the port.
User’s Manual of IGS-604HPT-M12 4.15 Network Diagnostics This section provide the Physical layer and IP layer network diagnostics tools for troubleshoot. The diagnostic tools are designed for network manager to help them quickly diagnose problems between point to point and better service customers. Use the Diagnostics menu items to display and configure basic administrative details of the Industrial Managed Switch.
User’s Manual of IGS-604HPT-M12 4.15.1 Ping This page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues. After you press “Start”, 5 ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon reception of a reply. The page refreshes automatically until responses to all packets are received, or until a timeout occurs. The ICMP Ping screen in Figure 4-15-1 appears.
User’s Manual of IGS-604HPT-M12 4.15.2 IPv6 Ping This page allows you to issue ICMPv6 ping packets to troubleshoot IPv6 connectivity issues. After you press “Start”, 5 ICMPv6 packets are transmitted, and the sequence number and roundtrip time are displayed upon reception of a reply. The page refreshes automatically until responses to all packets are received, or until a timeout occurs. The ICMPv6 Ping screen in Figure 4-15-2 appears.
User’s Manual of IGS-604HPT-M12 4.15.3 Remote IP Ping Test This page allows you to issue ICMP ping packets to troubleshoot IP connectivity issues on special port. After you press “Test”, 5 ICMP packets are transmitted, and the sequence number and roundtrip time are displayed upon reception of a reply. The page refreshes automatically until responses to all packets are received, or until a timeout occurs. The ICMP Ping screen in Figure 4-15-3 appears.
User’s Manual of IGS-604HPT-M12 4.15.4 Cable Diagnostics This page is used for running the Cable Diagnostics. Press to run the diagnostics. This will take approximately 5 seconds. If all ports are selected, this can take approximately 15 seconds. When completed, the page refreshes automatically, and you can view the cable diagnostics results in the cable status table. Note that Cable Diagnostics is only accurate for cables of length 7 140 meters.
User’s Manual of IGS-604HPT-M12 Short C - Cross-pair short to pair C Short D - Cross-pair short to pair D Cross A - Abnormal cross-pair coupling with pair A Cross B - Abnormal cross-pair coupling with pair B Cross C - Abnormal cross-pair coupling with pair C Cross D - Abnormal cross-pair coupling with pair D Length: The length (in meters) of the cable pair. The resolution is 3 meters Buttons : Click to run the diagnostics.
User’s Manual of IGS-604HPT-M12 4.16 Power over Ethernet Providing up to 4 PoE, in-line power interfaces, the IGS-604HPT-M12 PoE Switch can easily build a power that centrally controls IP phone system, IP Camera system, AP group for the enterprise. For instance, 4 cameras/APs can be easily installed around the corners of the company for surveillance demands or a wireless roaming environment in the office can be built.
User’s Manual of IGS-604HPT-M12 4.16.1 Power over Ethernet Powered Device Voice over IP phones Enterprises can install PoE VoIP phones, ATA sand other Ethernet/non-Ethernet end-devices in the center where UPS is installed for 3~5 watts un-interruptible power system and power control system. Wireless LAN Access Points Access points can be installed at museums, sightseeing sites, airports, hotels, campuses, factories, warehouses, etc.
User’s Manual of IGS-604HPT-M12 4.16.2 System Configuration In a power over Ethernet system, operating power is applied from a power source (PSU or power supply unit) over the LAN infrastructure to powered devices (PDs), which are connected to ports. Under some conditions, the total output power required by PDs can exceed the maximum available power provided by the PSU.
User’s Manual of IGS-604HPT-M12 4.16.3 Power Over Ethernet Configuration This section allows the user to inspect and configure the current PoE configuration settings as Figure 4-16-2 appears. Figure 4-16-2: PoE Configuration Screenshot The page includes the following fields: Object Description System PoE Admin Allows user to enable or disable PoE function. It will cause all of PoE ports to Mode PoE Temperature supply or not supply power.
User’s Manual of IGS-604HPT-M12 PD Classifications A PD may be classified by the PSE based on the classification information provided by the PD. The intent of PD classification is to provide information about the maximum power required by the PD during operation. However, to improve power management at the PSE, the PD provides a signature about Class level. The PD is classified based on power.
User’s Manual of IGS-604HPT-M12 Sequential Power up Allows user to configure the PoE Port Start Up interval time. Interval Sequential Power up There are two modes for Starting Up the PoE Port By Port: The PoE Port will start up by following Port number. Port Option By Priority: The PoE Port will start up by following the PoE Priority. Buttons : Click to apply changes : Click to undo any changes made locally and revert to previously saved values. 4.16.
User’s Manual of IGS-604HPT-M12 AF/AT Mode Allows user to select 802.3at or 802.3af compatibility mode. The default value is 802.3at mode. This function will affect PoE power reservation under the power limit classification only. As in 802.3af mode, the system will reserve a maximum of 15.4W for PD that supports Class3 level. As in IEEE 802.3at mode, the system will reserve 30.8W for PD that supports Class4 level. From class1 to class3 level in the 802.
User’s Manual of IGS-604HPT-M12 4.16.6 PoE Status This page allows the user to inspect the total power consumption, total power reserved and current status for all PoE ports. The screen in Figure 4-16-5 appears. Figure 4-16-5:PoE Status Screenshot The page includes the following fields: Object Description Sequential Power On Displays the current sequential power on mode. System Power Budget Displays the maximum PoE power budget.
User’s Manual of IGS-604HPT-M12 Operation Mode Displays the current PoE operation mode. Current Budget Displays the current maximum PoE budget. Current Ports in Use Displays the current PoE ports in use. Class 1 ~ 4 ports Displays the current PoE class 1 ~ 4 ports. Power Consumption Displays the current power consumption (total watts and percentage) Reserved Power Shows how much the total power is reserved for all PDs.
User’s Manual of IGS-604HPT-M12 4.16.7 PoE Schedule This page allows the user to define PoE schedule and schedule power recycle. PoE Schedule Besides being used as an IP Surveillance, the Managed PoE switch is certainly applicable to constructing any PoE network including VoIP and Wireless LAN.
User’s Manual of IGS-604HPT-M12 The screen in Figure 4-16-6 appears. Figure 4-16-6: PoE Schedule Screenshot Please press Add New Rule button to start settingPoE Schedule function. You have to set PoE schedule via profile and then go back to PoE Port Configuration, and select “Schedule” mode from per port “PoE Mode” option and then you can indicate which schedule profile could be apply to the PoE port. The page includes the following fields: Object Description Profile Set the schedule profile mode.
User’s Manual of IGS-604HPT-M12 same time, please use this function. Don’t use Reboot Only function. This function offers administrator to reboot PoE device at an indicated time if administrator has this kind of requirement. Reboot Only Allows user to reboot PoE function by PoE reboot schedule. Please note that if administrator enables this function, PoE schedule will not set time to profile. This function is only for PoE port reset at the indicated time.
User’s Manual of IGS-604HPT-M12 This page provides you with how to configure PD Alive Check. The screen in Figure 4-16-7 appears. Figure 4-16-7: PD Alive Check Configuration Screenshot The page includes the following fields: Object Description Mode Allows user to enable or disable per port PD Alive Check function. By default, all ports are disabled. Ping PD IP Address This column allows user to set PoE device IP address for system making ping to the PoE device.
User’s Manual of IGS-604HPT-M12 Buttons : Click to apply changes 4.16.9 LLDP PoE Neighbours This page provides a status overview for all LLDP PoE neighbors. The displayed table contains a row for each port on which an LLDP PoE neighbor is detected. The columns hold the following information: The screen in Figure 4-16-8 appears.
User’s Manual of IGS-604HPT-M12 4.17 Loop Protection This chapter describes enabling loop protection function that provides loop protection to prevent broadcast loops in Industrial Managed Switch. 4.17.1 Configuration This page allows the user to inspect the current Loop Protection configurations, and possibly change them as well; screen in Figure 4-17-1 appears.
User’s Manual of IGS-604HPT-M12 loop is detected (and the port action shuts down the port). Valid values are 0 to 604800 seconds (7 days). A value of zero will keep a port disabled (until next device restart). Port Configuration Object Description Port The switch port number of the port. Enable Controls whether loop protection is enabled on this switch port. Action Configures the action performed when a loop is detected on a port.
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description Port The Industrial Managed Switch port number of the logical port. Action The currently configured port action. Transmit The currently configured port transmit mode. Loops The number of loops detected on this port. Status The current loop protection status of the port. Loop Whether a loop is currently detected on the port. Time of Last Loop The time of the last loop event detected.
User’s Manual of IGS-604HPT-M12 4.18 RMON RMON is the most important expansion of the standard SNMP. RMON is a set of MIB definitions, used to define standard network monitor functions and interfaces, enabling the communication between SNMP management terminals and remote monitors. RMON provides a highly efficient method to monitor actions inside the subnets. MID of RMON consists of 10 groups.
User’s Manual of IGS-604HPT-M12 protocol. InNUcastPkts: The number of broad-cast and multi-cast packets delivered to a higher-layer protocol. InDiscards: The number of inbound packets that are discarded even the packets are normal. InErrors: The number of inbound packets that contains errors preventing them from being deliverable to a higher-layer protocol. InUnknownProtos: the number of the inbound packets that is discarded because of the unknown or un-support protocol.
User’s Manual of IGS-604HPT-M12 : Click to undo any changes made locally and revert to previously saved values. 4.18.2 RMON Alarm Status This page provides an overview of RMON Alarm entries. Each page shows up to 99 entries from the Alarm table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the Alarm table.
User’s Manual of IGS-604HPT-M12 : Updates the table, starting from the first entry in the Alarm Table, i.e. the entry with the lowest ID. : Updates the table, starting with the entry after the last entry currently displayed. 4.18.3 RMON Event Configuration Configure RMON Event table on this page. The entry index key is ID; screen in Figure 4-18-3 appears. Figure 4-18-3: RMON Event Configuration Screenshot The page includes the following fields: Object Description Delete Check to delete the entry.
User’s Manual of IGS-604HPT-M12 4.18.4 RMON Event Status This page provides an overview of RMON Event table entries.Each page shows up to 99 entries from the Event table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the Event table. The first displayed will be the one with the lowest Event Index and Log Index found in the Event table; screen in Figure 4-18-4 appears.
User’s Manual of IGS-604HPT-M12 4.18.5 RMON History Configuration Configure RMON History table on this page. The entry index key is ID; screen in Figure 4-18-5 appears. Figure 4-18-5: RMON History Configuration Screenshot The page includes the following fields: Object Description Delete Check to delete the entry. It will be deleted during the next save. ID Indicates the index of the entry. The range is from 1 to 65535. Data Source Indicates the port ID which wants to be monitored.
User’s Manual of IGS-604HPT-M12 4.18.6 RMON History Status This page provides a detail of RMON history entries; screen in Figure 4-18-6 appears. Figure 4-18-6: RMON History Overview Screenshot The page includes the following fields: Object Description History Index Indicates the index of History control entry. Sample Index Indicates the index of the data entry associated with the control entry.
User’s Manual of IGS-604HPT-M12 Coll. The best estimate of the total number of collisions in this Ethernet segment. Utilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval is in the hundredths of a percent. Buttons : Click to refresh the page immediately. Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds.
User’s Manual of IGS-604HPT-M12 : Click to undo any changes made locally and revert to previously saved values. 4.18.8 RMON Statistics Status This page provides an overview of RMON Statistics entries. Each page shows up to 99 entries from the Statistics table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the Statistics table.
User’s Manual of IGS-604HPT-M12 CRC. Coll. The best estimate of the total number of collisions on this Ethernet segment. 64 Bytes The total number of packets (including bad packets) received that were 64 octets in length. 65~127 The total number of packets (including bad packets) received that were between 65 to 127 octets in length. 128~255 The total number of packets (including bad packets) received that were between 128 to 255 octets in length.
User’s Manual of IGS-604HPT-M12 4.19 PTP The Precision Time Protocol (PTP) is a protocol used to synchronize clocks throughout a computer network. On a local area network, it achieves clock accuracy in the sub-microsecond range, making it suitable for measurement and control systems. PTP was originally defined in the IEEE 1588-2002 standard, officially entitled "Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems" and published in 2002.
User’s Manual of IGS-604HPT-M12 2 Step Flag Master Only - clock's Device Type is Master Only. Slave Only - clock's Device Type is Slave Only Static member: defined by the system, true if two-step Sync events and Pdelay_Resp events are used. Clock Identity It shows unique clock identifier. One Way If true, one-way measurements are used. This parameter applies only to a slave. In one-way mode no delay measurements are performed, i.e.
User’s Manual of IGS-604HPT-M12 Synchronize to System Activate this button to synchronize the System Clock to PTP Time. Clock Ports Configuration Click to edit the port data set for the ports assigned to this clock instance. Clock Default Data Set Object Description Clock ID An internal instance id (0..3) Device Type Indicates the Type of the Clock Instance. There are five Device Types. Ord-Bound - clock's Device Type is Ordinary-Boundary Clock.
User’s Manual of IGS-604HPT-M12 VID VLAN Identifier used for tagging the VLAN packets. PCP Priority Code Point value used for PTP frames. Current Clock Data Set Object Description stpRm Steps Removed: It is the number of PTP clocks traversed from the grandmaster to the local slave clock. Offset from master Time difference between the master clock and the local slave clock, measured in ns.
User’s Manual of IGS-604HPT-M12 D-enable If true, the D part of the algorithm is included ‘P’ constant [1..1000] see above ‘I’ constant [1..1000] see above ‘D’ constant [1..1000] see above Unicast Slave Configuration Object Description Duration The number of seconds a master is requested to send Announce/Sync messages. The request is repeated from the slave for each duration (4 seconds).
User’s Manual of IGS-604HPT-M12 The page includes the following fields: Object Description One_pps_mode Shows the current One_pps_mode configured. 1. Output : Enable the 1 pps clock output 2. Input : Enable the 1 pps clock input 3. Disable : Disable the 1 pps clock in/out-put External Enable Shows the current External clock output configuration. 1. True : Enable the external clock output 2.
User’s Manual of IGS-604HPT-M12 4.20 Ring ITU-T G.8032 Ethernet Ring protection switching (ERPS) is a link layer protocol applied on Ethernet loop protection to provide sub-50ms protection and recovery switching for Ethernet traffic in a ring topology. ERPS provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the algorithms between them are not the same.
User’s Manual of IGS-604HPT-M12 4.20.1 MEP Configuration The Maintenance Entity Point instances are configured here; screen in Figure 4-20-1 appears. Figure 4-20-1: MEP Configuration Screenshot The page includes the following fields: Object Description Delete This box is used to mark a MEP for deletion in next Save operation. Instance The ID of the MEP. Click on the ID of a MEP to enter the configuration page. Domain Port: This is a MEP in the Port Domain. 'Flow Instance' is a Port.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add a new MEP entry : Click to refresh the page immediately. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. 4.20.2 Detailed MEP Configuration This page allows the user to inspect and configure the current MEP Instance; screen in Figure 4-20-2 appears.
User’s Manual of IGS-604HPT-M12 Direction See help on MEP to create Web. Residence Port See help on MEP to create Web. Flow Instance See help on MEP to create Web. Tagged VID See help on MEP to create Web. This MAC See help on MEP to create Web. Instance Configuration: Object Description Level See help on MEP to create Web. Format This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is defined by ITU. 'ICC' can be max. 6 char.
User’s Manual of IGS-604HPT-M12 Peer MEP ID This value will become an expected MEP ID in a received CCM - see 'cMEP'. Unicast Peer MAC This MAC will be used when unicast is selected with this peer MEP. Also this MAC is used to create HW checking of receiving CCM PDU (LOC detection) from this MEP. cLOC Fault Cause indicates that no CCM has been received (in 3,5 periods) - from this peer MEP. cRDI Fault Cause indicates that a CCM is received with Remote Defect Indication from this peer MEP.
User’s Manual of IGS-604HPT-M12 'Frame Rate' has to be the same. APS Protocol: Object Description Enable Automatic Protection Switching protocol information transportation based on transmitting/receiving R-APS/L-APS PDU can be enabled/disabled. Must be enabled to support ERPS/ELPS implementing APS. This is only valid with one Peer MEP configured. Priority The priority to be inserted as PCP bits in TAG (if any). Cast Selection of APS PDU transmitted unicast or multi-cast.
User’s Manual of IGS-604HPT-M12 4.20.3 Ethernet Ring Protocol Switch The Ethernet Ring Protection Switch instances are configured here; screen in Figure 4-20-3 appears. Figure 4-20-3: Ethernet Ring Protocol Switch Screenshot The page includes the following fields: Object Description Delete This box is used to mark an ERPS for deletion in next Save operation. Port 0 This will create Port 0 of the switch in the ring. Port 1 This will create "Port 1" of the switch in the Ring.
User’s Manual of IGS-604HPT-M12 Buttons : Click to add a new Protection group entry. : Click to refresh the page immediately. : Click to save changes. : Click to undo any changes made locally and revert to previously saved values.
User’s Manual of IGS-604HPT-M12 4.20.4 Ethernet Ring Protocol Switch Configuration This page allows the user to inspect and configure the current ERPS Instance; screen in Figure 4-20-4 appears. Figure 4-20-4: Ethernet Ring Protocol Switch Configuration Screenshot The page includes the following fields: Instance Data: Object Description ERPS ID The ID of the Protection group. Port 0 See help on ERPS to create Web. Port 1 See help on ERPS to create Web.
User’s Manual of IGS-604HPT-M12 Green: This ERPS is configured - is active. Guard Time Guard timeout value is to be used to prevent ring nodes from receiving outdated R-APS messages. The period of the guard timer can be configured in 10 ms steps between 10 ms and 2 seconds, with a default value of 500 ms WTR Time The Wait To Restore timing value is to be used in revertive switching.
User’s Manual of IGS-604HPT-M12 Instance State: Object Description Protection State ERPS state according to State Transition Tables in G.8032. Port 0 OK: State of East port is ok SF: State of East port is Signal Fail Port 1 OK: State of West port is ok SF: State of West port is Signal Fail Transmit APS The transmitted APS according to State Transition Tables in G.8032. Port 0 Receive APS The received APS on Port 0 according to State Transition Tables in G.8032.
User’s Manual of IGS-604HPT-M12 4.20.5 Ring Wizard This page allows the user to configure the ERPS by wizard; screen in Figure 4-20-4 appears. Figure 4-20-5: Ring Wizard Screenshot The page includes the following fields: Object Description All Switch Numbers Set all the switch numbers for the ring group. The default number is 3 and maximum number is 30. Number ID The switch where you are requesting ERPS. Port Configures the port number for the MEP. VLAN Set the ERPS VLAN.
User’s Manual of IGS-604HPT-M12 4.20.6 Ring Wizard Example: Figure 4-20-6: Ring Example Diagram The above topology often occurs on using ERPS protocol. The multi switch constitutes a single ERPS ring; all of the switches only are configured as an ERPS in VLAN 3001, thereby constituting a single MRPP ring.
User’s Manual of IGS-604HPT-M12 Setup steps Set ERPS Configuration on Switch 1 Connect PC to switch 1 directly; don’t connect to port 1 & 2 Logging on to Switch 1 and click “Ring > Ring Wizard” Set “All Switch Number” = 3 and “Number ID” = 1; click the “Next” button to set the ERPS configuration for Switch 1. Set “MEP1” = Port1, “MEP2” = Port2 and VLAN ID = 3001; click the “Set” button to save the ERPS configuration for Switch 1.
User’s Manual of IGS-604HPT-M12 Set “MEP5” = Port2, “MEP6” = Port1 and VLAN ID = 3001; click the “Set” button to save the ERPS configuration for Switch 3. To avoid loop, please don’t connect switches 1, 2 & 3 together in the ring topology before configuring the end of ERPS .
User’s Manual of IGS-604HPT-M12 5. SWITCH OPERATION 5.1 Address Table The Industrial Managed Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Industrial Managed Switch. 5.2 Learning When one packet comes in from any port, the Industrial Managed Switch will record the source address, port no.
User’s Manual of IGS-604HPT-M12 The Industrial Managed Switch performs "Store and Forward"; therefore, no error packets occur. More reliably, it reduces the re-transmission rate. No packet loss will occur. 5.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset).
User’s Manual of IGS-20040MT 6. TROUBLESHOOTING This chapter contains information to help you solve issues. If the Industrial Managed Switch is not functioning properly, make sure the Industrial Managed Switch was set up according to instructions in this manual. ■ The Link LED is not lit Solution: Check the cable connection and remove duplex mode of the Industrial Managed Switch.
User’s Manual of IGS-20040MT APPENDIX A: Networking Connection A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T PIN NO MDI MDI-X 1 BI_DA+ BI_DB+ 2 BI_DA- BI_DB- 3 BI_DB+ BI_DA+ 4 BI_DC+ BI_DD+ 5 BI_DC- BI_DD- 6 BI_DB- BI_DA- 7 BI_DD+ BI_DC+ 8 BI_DD- BI_DC- Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. A.
User’s Manual of IGS-20040MT The standard cable, RJ45 pin assignment 6 321 6 321 6 3 21 The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
User’s Manual of IGS-604HPT-M12 APPENDIX B : GLOSSARY A ACE ACE is an acronym for Access Control Entry. It describes access permission associated with a particular ACE ID. There are three ACE frame types (Ethernet Type, ARP, and IPv4) and two ACE actions (permit and deny). The ACE also contains many detailed, different parameter options that are available for individual application. ACL ACL is an acronym for Access Control List.
User’s Manual of IGS-604HPT-M12 ACL|Rate Limiters: Under this page you can configure the rate limiters. There can be 15 different rate limiters, each ranging from 1-1024K packets per seconds. Under "Ports" and "Access Control List" web-pages you can assign a Rate Limiter ID to the ACE(s) or ingress port(s). AES AES is an acronym for Advanced Encryption Standard. The encryption key protocol is applied in 802.1i standard to improve WLAN security. It is an encryption standard by the U.S.
User’s Manual of IGS-604HPT-M12 Auto-Negotiation Auto-negotiation is the process where two different devices establish the mode of operation and the speed settings that can be shared by those devices for a link. C CC CC is an acronym for Continuity Check. It is a MEP functionality that is able to detect loss of continuity in a network by transmitting CCM frames to a peer MEP. CCM CCM is an acronym for Continuity Check Message.
User’s Manual of IGS-604HPT-M12 The DHCP server ensures that all IP addresses are unique, for example, no IP address is assigned to a second client while the first client's assignment is valid (its lease has not expired). Therefore, IP address pool management is done by the server and not by a human network administrator. Dynamic addressing simplifies network administration because the software keeps track of IP addresses rather than requiring an administrator to manage the task.
User’s Manual of IGS-604HPT-M12 Dotted Decimal Notation Dotted Decimal Notation refers to a method of writing IP addresses using decimal numbers and dots as separators between octets. An IPv4 dotted decimal address has the form x.y.z.w, where x, y, z, and w are decimal numbers between 0 and 255. DSCP DSCP is an acronym for Differentiated Services Code Point. It is a field in the header of IP packets for packet classification purposes.
User’s Manual of IGS-604HPT-M12 HTTP defines how messages are formatted and transmitted, and what actions Web servers and browsers should take in response to various commands. For example, when you enter a URL in your browser, this actually sends an HTTP command to the Web server directing it to fetch and transmit the requested Web page. The other main standard that controls how the World Wide Web works is HTML, which covers how Web pages are formatted and displayed.
User’s Manual of IGS-604HPT-M12 IGMP IGMP is an acronym for Internet Group Management Protocol. It is a communications protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. It is an integral part of the IP multicast specification, like ICMP for unicast connections. IGMP can be used for online video and gaming, and allows more efficient use of resources when supporting these uses.
User’s Manual of IGS-604HPT-M12 IP Source Guard IP Source Guard is a secure feature used to restrict IP traffic on DHCP snooping untrusted ports by filtering traffic based on the DHCP Snooping Table or manually configured IP Source Bindings. It helps prevent IP spoofing attacks when a host tries to spoof and use the IP address of another L LACP LACP is an IEEE 802.3ad standard protocol. The Link Aggregation Control Protocol, allows bundling several physical ports together to form a single logical port.
User’s Manual of IGS-604HPT-M12 addresses. Dynamic entries are removed from the MAC table if no frame with the corresponding SMAC address have been seen after a configurable age time. MEP MEP is an acronym for Maintenance Entity Endpoint and is an endpoint in a Maintenance Entity Group (ITU-T Y.1731). MD5 MD5 is an acronym for Message-Digest algorithm 5. MD5 is a message digest algorithm, used cryptographic hash function with a 128-bit hash value. It was designed by Ron Rivest in 1991.
User’s Manual of IGS-604HPT-M12 computers to communicate within a Local Area Network (LAN), and it is not supported on a Wide Area Network (WAN). The NetBIOS giving each computer in the network both a NetBIOS name and an IP address corresponding to a different host name, provides the session and transport services described in the Open Systems Interconnection (OSI) model. NFS NFS is an acronym for Network File System.
User’s Manual of IGS-604HPT-M12 P PCP PCP is an acronym for Priority Code Point. It is a 3-bit field storing the priority level for the 802.1Q frame. It is also known as User Priority. PD PD is an acronym for Powered Device. In a PoE> system the power is delivered from a PSE ( power sourcing equipment ) to a remote device. The remote device is called a PD. PHY PHY is an abbreviation for Physical Interface Transceiver and is the device that implement the Ethernet physical layer (IEEE-802.3).
User’s Manual of IGS-604HPT-M12 using POP or IMAP. IMAP4 and POP3 are the two most prevalent Internet standard protocols for e-mail retrieval. Virtually all modern e-mail clients and servers support both. PPPoE PPPoE is an acronym for Point-to-Point Protocol over Ethernet. It is a network protocol for encapsulating Point-to-Point Protocol (PPP) frames inside Ethernet frames.
User’s Manual of IGS-604HPT-M12 Achieving the required QoS becomes the secret to a successful end-to-end business solution. Therefore, QoS is the set of techniques to manage network resources. QoS class Every incoming frame is classified to a QoS class, which is used throughout the device for providing queuing, scheduling and congestion control guarantees to the frame according to what was configured for that specific QoS class. There is a one to one mapping between QoS class, queue and priority.
User’s Manual of IGS-604HPT-M12 Samba can be installed on a variety of operating system platforms, including Linux, most common Unix platforms, OpenVMS, and IBM OS/2. Samba can also register itself with the master browser on the network so that it would appear in the listing of hosts in Microsoft Windows "Neighborhood Network". SHA SHA is an acronym for Secure Hash Algorithm. It designed by the National Security Agency (NSA) and published by the NIST as a U.S. Federal Information Processing Standard.
User’s Manual of IGS-604HPT-M12 choose one to connect to based on pre-configuration, or by displaying a list of SSIDs in range and asking the user to select one (wikipedia). SSH SSH is an acronym for Secure SHell. It is a network protocol that allows data to be exchanged using a secure channel between two networked devices. The encryption used by SSH provides confidentiality and integrity of data over an insecure network.
User’s Manual of IGS-604HPT-M12 responsible for ensuring that a message is divided into the packets that IP manages and for reassembling the packets back into the complete message at the other end. Common network applications that use TCP include the World Wide Web (WWW), e-mail, and File Transfer Protocol (FTP). TELNET TELNET is an acronym for TELetype NETwork.
User’s Manual of IGS-604HPT-M12 sequencing of the packets. This means that the application program that uses UDP must be able to make sure that the entire message has arrived and is in the right order. Network applications that want to save processing time because they have very small data units to exchange may prefer UDP to TCP. UDP provides two services not provided by the IP layer.
User’s Manual of IGS-604HPT-M12 Voice VLAN Voice VLAN is VLAN configured specially for voice traffic. By adding the ports with voice devices attached to voice VLAN, we can perform QoS-related configuration for voice data, ensuring the transmission priority of voice traffic and voice quality. W WEP WEP is an acronym for Wired Equivalent Privacy. WEP is a deprecated algorithm to secure IEEE 802.11 wireless networks.
User’s Manual of IGS-604HPT-M12 WPS WPS is an acronym for Wi-Fi Protected Setup. It is a standard for easy and secure establishment of a wireless home network. The goal of the WPS protocol is to simplify the process of connecting any home device to the wireless network (Wikipedia). WRES WRED is an acronym for Weighted Random Early Detection. It is an active queue management mechanism that provides preferential treatment of higher priority frames when traffic builds up within a queue.
