Datasheet

IGS-604HPT-M12
2
Dual Power Input for High Availability Network System
The IGS-604HPT-M12 features a strong dual power input system (Dual 48V~56V DC)
incorporated into customer’s automation network to enhance system reliability and
uptime. For example, when DC Power 1 fails to work, the hardware failover function
will be activated automatically to keep powering the IGS-604HPT-M12 via DC Power 2
alternatively without any loss of operation.
Centralized Power Management for Gigabit Ethernet PoE Networking
To fulfill the needs of higher power required PoE network applications with Gigabit speed
transmission, the IGS-604HPT-M12 features high-performance Gigabit IEEE 802.3at
PoE+ (up to 36 watts) on all ports. It perfectly meets the power requirements of PoE VoIP
phone, PoE Wireless AP and all kinds of PoE IP cameras such as IR, PTZ, speed dome
cameras and even box type IP cameras with a built-in fan and heater for high power
consumption. The IGS-604HPT-M12’s PoE capabilities also help to reduce deployment
costs for network devices as a result of freeing from restrictions of power outlet locations.
Power and data switching are integrated into one unit, delivered over a single cable and
managed centrally. It thus eliminates cost for additional AC wiring and reduces installation
time.
Waterproof and Dustproof M12 Ethernet Connector
The IGS-604HPT-M12 is equipped with a 6-port 10/100/1000BASE-T auto-negotiation
waterproof and dustproof M12 connector with 4-port IEEE 802.3at PoE+ (Port 3 to Port 6);
each PoE port provides 36-watt PoE output. The M12 connector provides tight and strong
connection and guarantees stable Ethernet operation performance under high vibration
and shock environment and ensures it comes with the industrial protection rating of IP67
capable of withstanding humidity, dirt, dust, shock, vibrations, heat and cold.
Environmentally Hardened Design
The IGS-604HPT-M12 is able to protect itself from dust and water ingress, and to operate
under the temperature range from -40 to 75 degrees C. All these features ensure the
highestlevelofreliabilityformission-criticalapplicationsinanydifcultenvironment.
• High performance of Store-and-Forward architecture, and runt/
CRClteringthateliminateserroneouspacketstooptimize
the network bandwidth
• Storm control support
– Broadcast/Multicast/Unicast
• Supports VLAN
– IEEE 802.1Q tagged VLAN
– Up to 255 VLANs groups, out of 4095 VLAN IDs
– Provides Bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
– Private VLAN Edge (PVE)
– Protocol-based VLAN
– MAC-based VLAN
– IP subnet-based VLAN
– Voice VLAN
• Supports Spanning Tree Protocol
– IEEE 802.1D Spanning Tree Protocol (STP)
– IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
– IEEE 802.1s Multiple Spanning Tree Protocol (MSTP),
spanning tree by VLAN
– BPDU Guard
• Supports Link Aggregation
– 802.3ad Link Aggregation Control Protocol (LACP)
– Cisco ether-channel (static trunk)
– Maximum 3 trunk groups, with 2 ports for each trunk
– Up to 4Gbps bandwidth (full duplex mode)
• Provides port mirror (many-to-1)
• Portmirroringmonitorstheincomingoroutgoingtrafcona
particular port
• Loop protection to avoid broadcast loops
• Supports E.R.P.S. (Ethernet Ring Protection Switching)
• IEEE 1588 and synchronous Ethernet network timing
Quality of Service
• Ingress shaper and egress rate limit per port bandwidth
control
• 8 priority queues on all switch ports
• Trafcclassication
– IEEE 802.1p CoS
– ToS/DSCP/IP precedence of IPv4/IPv6 packets
– IP TCP/UDP port number
– Typical network application
• Strict priority and Weighted Round Robin (WRR) CoS policies
• Trafc-policingpoliciesontheswitchport
• DSCP remarking
Multicast
• Supports IGMP snooping v1, v2 and v3
• Supports MLD snooping v1 and v2
• Querier mode support
• IGMPsnoopingportltering