Datasheet

IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-8P2T4S
9
Specications
Product
IGS-5225-8P4S IGS-5225-8P2T2S IGS-5225-8P2T4S
HardwareSpecications
Hardware Version v4 v3 v1
Copper Ports
8 10/100/1000BASE-T RJ45
auto-MDI/MDI-X ports
10 10/100/1000BASE-T RJ45
auto-MDI/MDI-X ports
10 10/100/1000BASE-T RJ45
auto-MDI/MDI-X ports
SFP Fiber Ports
2 100/1000BASE-X SFP interfaces
(Port-9 and Port-10)
2 100/1000/2500BASE-X SFP
interfaces (Port-11 and Port-12)
2 100/1000/2500BASE-X SFP
interfaces (Port-11 and Port-12)
2 100/1000BASE-X SFP interfaces
(Port-11 and Port-12)
2 100/1000/2500BASE-X SFP
interfaces (Port-13 and Port-14)
PoE Injector Ports 8 ports with 802.3at/af PoE injector function with Port-1 to Port-8
Console 1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
RAM 128MBytes
Flash Memory 64MBytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
ESD Protection 6KV DC
Enclosure IP30 aluminum case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
Digital Input 2 digital input (DI)
Level 0: -24V~2.1V (±0.1V)
Level 1: 2.1V~24V (±0.1V)
Input load to 24V DC, 10mA max.
Digital Output 2 digital output (DO) Open collector to 24V DC, 100mA max.
Dimensions (W x D x H) 76.8 x 107.3 x 152 mm
Weight 110 4g 1103g 1.1g
Power Requirements Dual 48~56V DC (>51V DC for PoE+ output recommended)
Power Consumption
Max. 6.48 watts/22.11BTU (Power on
without any connection)
Max. 262 watts/893.42BTU (Full
loading with PoE function)
Max. 6.48 watts/22.11BTU (Power
on without any connection)
Max.271 watts/924.65BTU (Full
loading with PoE function)
Max. 7W/23.88 BTU (Power on)
Max. 262W/893.98 BTU(Full
Loading with PoE function)
LED Indicator
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Ring (Green)
Ring Owner (Green)
DIDO (Red)
Per 10/100/1000T RJ45 PoE+ Ports:
PoE-in-Use (Amber)
LNK/ACT (Green)
Per 10/100/1000T RJ45Ports:
1000 LNK/ACT (Green)
100 LNK/ACT (Amber)
Per SFP Interface:
10/100 LNK/ACT (Amber)
1G/2.5G LNK/ACT (Green)
Switching
Switch Architecture Store-and-Forward
Switch Fabric 30Gbps/non-blocking 30Gbps/non-blocking 34Gbps/non-blocking
Throughput (packet per second) 22.32Mpps@ 64 bytes packet 22.32Mpps@ 64 bytes packet 25.30Mpps@ 64bytes packet
Installation Wall-mount kit and DIN-rail kit
Address Table 8K entries, automatic source address learning and aging
Shared Data Buffer 4Mbits
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 9K bytes
Power Over Ethernet