(V3) Datasheet

IGS-5225-8P2S2X
10
Specications
Product
IGS-5225-8P2S2X
Hardware Specications
Hardware Version 3
Copper Ports 8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP/mini-GBIC Slots
2 1000BASE-SX/LX/BX SFP interfaces (Port-9 and Port-10)
Compatible with 100BASE-FX and 2500BASE-X SFP
SFP+ Slots
2 10GbBASE-SR/LR SFP+ interfaces (Port-11 and Port-12)
Compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP transceiver
PoE Injector Port 8 ports with 802.3at/af PoE injector function with Port-1 to Port-8
Console 1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 66Gbps/non-blocking
Throughput (packet per second) 49.107Mpps@ 64Bytes packet
Address Table 32K entries, automatic source address learning and aging
Shared Data Buffer 16Mbits
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 10Kbytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
ESD Protection 6KV DC
Enclosure IP30 aluminum case
Installation DIN rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
DI & DO
2 Digital Input (DI):
Level 0: -24V~2.1V (±0.1V)
Level 1: 2.1V~24V (±0.1V)
Input load to 24V DC, 10mA max.
2 Digital Output (DO): Open collector to 24V DC, 100mA max.
LED Indicator
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Ring (Green)
R.O. (Green)
DIDO (Red)
Per 10/100/1000T RJ45 Ports:
LNK/ACT (Green)
PoE In-Use (Orange)
Per 100/1000/2500BASE-X SFP Interface:
1G/2.5G LNK/ACT (Green)
100 LNK/ACT (Orange)
Per SFP+ Interface:
1G/2.5G LNK/ACT (Green)
10G LNK/ACT (Orange)
Dimensions (W x D x H) 72 x 107 x 152 mm
Weight 1684g
Power Requirements Dual 48~56V DC (>51V DC for PoE+ output recommended)
Power Consumption
Max. 11.1 watts/37.87BTU (Power on without any connection)
Max. 306 watts/1043.46BTU (Full loading with PoE function)
Power Over Ethernet
PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply Type End-span
PoE Power Output
IEEE 802.3af Standard
- Per port 48V~51V DC (depending on the power supply), max. 15.4 watts
IEEE 802.3at Standard
- Per port 51V~56V DC (depending on the power supply), max. 36 watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget Dual power input: 240W maximum (depending on power input)