Industrial L3 Multi-Port Full Gigabit Managed Ethernet Switch IGS-5225-8T2S2X/IGS-5225-8P2S2X Quick Installation Guide
Table of Contents 1. Package Contents....................................................................... 3 2. Requirements............................................................................. 4 3. Wiring the Power Inputs............................................................. 5 4. Terminal Setup........................................................................... 7 4.1 Logon to the Console........................................................... 8 4.2 Configuring IP Address........
1. Package Contents Thank you for purchasing PLANET L3 Industrial Managed Switch, IGS-5225-8T2S2X and IGS-5225-8P2S2X. The descriptions of these models are as follows: IGS-5225-8T2S2X: Industrial L3 8-Port 10/100/1000T + 2-Port 100/1000X SFP + 2-Port 10G SFP+ Managed Ethernet Switch (-40~75 degrees C) IGS-5225-8P2S2X: Industrial L3 8-Port 10/100/1000T 802.
2. Requirements The Industrial Managed Switch provides remote login interface for management purposes. The following equipment is necessary for further management: zz Workstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later, Linux, UNIX, or other platforms are compatible with TCP/IP Protocols. zz Workstations are installed with Ethernet NIC (Network Interface Card) zz Serial Port Connection (Terminal) The above Workstations come with COM Port (DB9) or USB-toRS232 converter.
3. Wiring the Power Inputs The Upper Panel of the Industrial Managed Switch indicates a DC inlet power socket and consists of one terminal block connector within 6 contacts. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5 and 6 for Power 2.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 V+ VPower 1 Model IGS-5225-8T2S2X IGS-5225-8P2S2X Note 6 3 4 5 6 V+ VPower 2 Positive (+) Pin Negative (-) Pin Pin 1/5 Pin 2/6 The wire gauge for the terminal block should be in the range from 12 to 24 AWG. Please check with wire AWG Ampere spec, before connecting PLANET Industrial Switch.
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type serial (console) port of the Industrial Managed Switch. The console port of the Industrial Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of null modem. IGS Industrial Managed Switch PC/Workstation with Terminal emulation software IP Address: 192.168.0.
4.1 Logon to the Console Once the terminal has been connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. Then, the following message asks to log in user name and password. The factory default user name and password are shown as follows and the login screen in Figure 5-1 appears User Name: admin Password: admin Figure 4-1: Console Login Screen The user can now enter commands to manage the Industrial Managed Switch.
To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Display of the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address shown in Figure 4-2 Figure 4-2: IP Information Screen Configuration of the IP Address 3. At the “#” prompt, enter the following command and press as shown in Figure 4-3.
4.3 Store the Current Switch Configuration At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 4-4: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.
5. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Industrial Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Default IP Address: 192.168.0.100 Default User Name: admin Default Password: admin Figure 5-2: Login Screen 3. After entering the password, the main screen appears as shown in Figure 5-3.
4. The Switch Main Menu is shown on top of the Web page, and the functions are shown on the left to configure the Industrial Managed Switch. Now, you can use the Web management interface to continue the Switch management. Please refer to the user manual for more. Note If you are not familiar with Switch functions or the related parameter, press “Help icon” anytime on the Web page to get the help description. 5.
1. Click Maintenance > Open Switch Maintenance on the left page > Press Save Startup Config. 2. Or you can press the “Save Configuration” button. 3. Press the “Save Configuration” button to save.
6. Resetting the Switch to Default To reset the IP address to the default IP address “192.168.0.100” and the user password to factory default mode (default password is admin), press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of 192.168.0.xx and default password. Be noted that all the previous setups will be disappeared after the factory default reset is made.
7. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: https://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw IGS-5225-8T2S2X/IGS-5225-8P2S2X User’s Manual: https://www.planet.com.
