User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.6 Remote Management
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet
- 4.7 Ring
- 4.8 ONVIF
- 4.9 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-5225 series
396
Figure 4-6-1-2: PoE Configuration Screenshot
The page includes the following fields:
Object Description
• System PoE Admin Mode
Allows user to enable or disable PoE function. It will causes all of PoE ports to supply
or not supply power.
• PoE Temperature Protection
Allows user to enable or disable PoE Temperature Protection.
• PoE Management Mode
There are two modes for configuring how the ports/PDs may reserve power and when
to shut down ports.
Classification mode: System offers PoE power according to PD real power
consumption.
Allocation mode: Users are allowed to assign how much PoE power for each
port and system will reserve PoE power to PD.
• PoE Legacy Mode
In the legacy mode, the IEEE method will be tried first and if it fails to discover a valid
PD, the legacy capacitance measurement with a large capacitance value will be used
to detect a legacy PD. This mode is used to support legacy devices. The default mode
is IEEE mode. Enabled legacy mode could damage non-PD devices.
• Power Supply Budget [W]
Set limit value of the total PoE port providing power to the PDs.
• Temperature Threshold
This is PoE temperature threshold for user set up a temperature parameter for alarm.
• PoE Usage Threshold
This is a parameter for user to define that if PoE power has been consumed to the
setting then a alarm log will be issued.
Buttons
: Click to apply changes
: Click to undo any changes made locally and revert to previously saved values.