User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet
- 4.7 Ring
- 4.8 ONVIF
- 4.9 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-5225 series
29
10mA max
2 Digital Output (DO)
Open collector to 24V DC,
100mA max.
N/A N/A
Power Requirements Dual 48~56V DC (>52V DC for PoE+ output recommended)
LED Indicator
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Ring (Green)
Ring Owner (Green)
DIDO (Red)
Per 10/100/1000T RJ45
Ports:
100 LNK/ACT (Amber)
1000 LNK/ACT (Green)
Per SFP Interface:
100 LNK/ACT (Amber)
1000 LNK/ACT (Green)
Per PoE Port:
Ultra 60W PoE-in-
use
x 1 (Green)
802.3at/af PoE-in-
use
x1 (Amber)
PoE Usage:
60W, 120W, 180W,
240W (Green)
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Ring (Green)
Ring Owner (Green)
Per 10/100/1000T RJ45
PoE+ Ports:
PoE-in-Use (Amber)
LNK/ACT (Green)
Per SFP Interface:
100 LNK/ACT (Amber)
1000 LNK/ACT
(Green)
PoE Usage:
30W, 60W, 90W,
120W (Amber)
System:
Power 1 (Green)
Power 2 (Green)
Fault Alarm (Red)
Ring (Green)
Ring Owner (Green)
Per 10/100/1000T RJ45
Ports:
10/100Mbps LNK/ACT
(Amber)
1000 LNK/ACT (Green)
Per SFP Interface:
100 LNK/ACT (Amber)
1000 LNK/ACT (Green)
Dimensions (WxDxH)
72 x 107 x 152 mm 50 x 87.8 x 135 mm 32 x 87x 135 mm
Weight 1050g 610g 456g
Power Requirements
48~56V DC (>52V DC for
PoE+ output
recommended)
48~56V DC (>52V DC for
PoE+ output
recommended)
Dual 12~48V DC
24V AC
Power Consumption
Max. 6.6 watts/22.52BTU
(Power on without any
connection)
Max. 6.2 watts/26.76BTU
(Power on without any
connection)
Max. 6.3 watts/21.6 BTU
(Power on without any
connection)
Max. 282 watts/962.22BTU
(Full loading with Ultra PoE
function)
Max. 151.8
watts/520.82BTU (Full
loading with PoE function)
Max. 8.5 watts/29.2 BTU
(Full loading)
Power Over Ethernet
PoE Standard
IEEE
802.3af/802.3at/802.3bt
Ultra PoE PSE
IEEE 802.3at Power over
Ethernet Plus/PSE
N/A
PoE Power Supply Type End-span/Mid-span/UPoE End-span N/A
PoE Power Output
IEEE 802.3af Standard
- Per port 48V~52V DC
(depending on the power
supply), max. 15.4 watts
IEEE 802.3af Standard
- Per port 48V~51V DC
(depending on the power
supply), max. 15.4 watts
N/A