User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.3.14 Link OAM
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet
- 4.7 Ring
- 4.8 ONVIF
- 4.9 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS-5225 series
28
IGS-5225-4UP1T2S/IGS-5225-4P2S/IGS-5225-4T2S
Product IGS-5225-4UP1T2S IGS-5225-4P2S IGS-5225-4T2S
Hardware Specification
s
Copper Ports
5 10/100/1000BASE-T
RJ45 auto-MDI/MDI-X
ports
4 10/100/1000BASE-T
RJ45 auto-MDI/MDI-X
ports
4 10/100/1000BASE-T
RJ45 auto-MDI/MDI-X
ports
SFP/mini-GBIC Slots
2 1000BASE-SX/LX/BX
SFP interfaces (Port-6 to
Port-7)
Compatible with
100BASE-FX SFP
2 1000BASE-SX/LX/BX
SFP interfaces (Port-6 to
Port-7)
Compatible with
100BASE-FX SFP
2 1000BASE-SX/LX/BX
SFP interfaces (Port-6 to
Port-7)
Compatible with
100BASE-FX SFP
PoE Injector Port
4 ports with Ultra
PoE/802.3at/af PoE
injector function with Port-
1
to Port-4
4 ports /802.3at/af PoE
injector function with Port-
1
to Port-4
N/A
Console
1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Switch Architecture
Store-and-Forward
Switch Fabric 14Gbps/non-blocking 12Gbps/non-blocking 12Gbps/non-blocking
Throughput (packet per
second)
10.42Mpps@ 64 bytes
packet
8.928Mpps@ 64 bytes
packet
8.928Mpps@ 64 bytes
packet
Address Table
8K entries, automatic source address learning and aging
Shared Data Buffer
4Mbits
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
Jumbo Frame 9Kbytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
ESD Protection
6KV DC
Enclosure IP30 aluminum case IP40 metal case IP30 metal case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal
block for power input
Pin 1/2 for Power 1,
Pin 3/4
for fault alarm, Pin 5/6 for
Power 2
Removable 6-pin terminal
block for power input
Pin 1/2 for Power 1,
Pin 3/4
for fault alarm, Pin 5/6 for
Power 2
Removable 6-pin terminal
block for power input
Pin 1/2 for Power 1,
Pin 3/4
for fault alarm, Pin 5/6 for
Power 2
Removable 6-pin terminal
block for DI/DO interface
Pin 1/2 for DI 1 & 2,
Pin 3/4
for DO 1 & 2, Pin 5/6 for
GND
N/A N/A
Alarm
One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
DI/DO
2 Digital Input (DI)
Level 0: -24V~2.1V (±0.1V)
Level 1: 2.1V~24V (±0.1V)
Input load to 24V DC,
N/A N/A