User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
2. Tighten the wire-clamp screws for preventing the wires from
loosening.
1 2 3 4 5 6
Power 1 Alarm Power 2
+ - + -
Note
1. The wire gauge for the terminal block should be
in the range between 12 and 24 AWG.
2. The IGS-501T power input range is 9V ~ 48V
DC and supports 24V AC.
3. The IGS-801T power input range is 12V ~ 48V
DC and supports 24V AC.
4 Use one power input when using 24V AC.
Note
1. The wire gauge for the terminal block should be
in the range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A
currents.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
4. Installation
4.1 DIN-rail Mounting Installation
The DIN-rail is screwed on the Industrial Gigabit Ethernet
Switch when out of factory. When you need to replace the wall-
mount application with DIN-rail application on Industrial Gigabit
Ethernet Switch, please refer to the following gures to screw
the DIN-rail on the Industrial Gigabit Ethernet Switch. To hang
the Industrial Gigabit Ethernet Switch, follow the steps below:
3.5 Grounding the Device
Users MUST complete grounding wired with the device;
otherwise, a sudden lightning could cause fatal damage to the
device.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1.2A max.
AC Input: 24V
, 1.1A max.
V1+ V2+
PWR1
PWR2Alarm
1 2 3 4 5 6
Earth Ground
3.6 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the
Industrial Gigabit Ethernet Switch will detect the fault status of
the power failure and then form an open circuit. The following
illustration shows an application example for wiring the fault
alarm contacts.
Insert the wires into the fault alarm contacts
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : 5/8-Port 10/100/1000T Industrial Gigabit Ethernet Switch
*Model Number : IGS-501T, IGS-801T
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2014/30/EU).
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015 + AC:2016)
EN 55024 (2010 + A1:2015)
EN 55035 (2017)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan,
R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
May 28, 2018
Place
Date
Legal Signature
4.2 Wall-mount Plate Mounting
4.3 Side Wall-mount Plate Mounting
Caution
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts
by using incorrect screws would invalidate your
warranty.
5. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to
check if it could solve your issue. If you need more support
information, please contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=3
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.