User's Manual
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 5-/8-Port 10/100/1000T
industrial Gigabit Ethernet Switch, IGS-501T/IGS-801T. In the
following section, the term “Industrial Gigabit Ethernet
Switch” means the IGT-501T/IGT-801T.
Open the box of the Industrial Gigabit Ethernet Switch and
carefully unpack it. The box should contain the following items:
Industrial Gigabit Ethernet
Switch x 1
User’s Manual x 1
DIN-rail Kit x 1 Wall-mount Kit x 1
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.
Switch Fabric 10Gbps 16Gbps
Throughput
(packet per second)
7.4Mpps 11.9Mpps
Jumbo Frame 9K
Network Cables
10/100/1000BASE-T:
Cat. 3, 4, 5, 5e, 6 UTP cable
(100 meters, max.)
EIA/TIA-568 100-ohm STP
(100 meters, max.)
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy-Ecient Ethernet
IEEE 802.1p Class of Service
Temperature
Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity
Operating: 5% to 90%,
Storage: 5% to 90% (non-condensing)
Regulatory
Compliance
FCC Part 15 Class A, CE
3.3 Switch Upper Panel
The upper panel of the Industrial Gigabit Ethernet Switch
consists of one terminal block connector within two DC power
inputs.
Figures 3-3 and 3-4 show the upper panel of the Industrial
Gigabit Ethernet Switch.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1.2A max.
AC Input: 24V
, 1.1A max.
V1+ V2+
PWR1
PWR2Alarm
1 2 3 4 5 6
Figure 3-3: IGS-501T Upper Panel
Max. fault loading: 24V, 1A
V1+
V2+
PWR1
PWR2Fault
DC Input: 12-48V
, 1.2A max.
AC Input: 24V
, 1.1A max.
1 2 3 4 5 6
Figure 3-4: IGS-801T Upper Panel
3.2 LED Indicators
IGS-501T:
LED Color Function
P1 Green Lit to indicate power 1 has power.
P2 Green Lit to indicate power 2 has power.
Alarm Red
Lit to indicate either power 1 or power 2
has no power.
1000
LNK/ACT
Green
Lit to indicate the port is successfully
connecting to the network at 1000Mbps.
O to indicate that the port is successfully
connecting to the network at 10Mbps or
100Mbps.
Blinking to indicate that the port is actively
sending or receiving data.
10/100
LNK/ACT
Amber
Lit to indicate the port is successfully
connecting to the network at 100Mbps or
10Mbps.
O to indicate that the port is successfully
connecting to the network at 1000Mbps.
Blinking to indicate that the port is actively
sending or receiving data.
2.ProductSpecications
Model IGS-501T IGS-801T
Hardware Specications
10/100/1000BASE-T
Ports
5 8
Dimensions
(W x D x H)
32 x 87 x 135 mm
Weight 430g 476g
Power Requirements
9~48V DC,
redundant power
with reverse
polarity protection
function, 24V AC
power support
12~48V DC,
redundant power
with reverse
polarity protection
function, 24V AC
power support
Power Consumption/
Dissipation
2.8 watts/9.5BTU 6.72 watts/23BTU
Installation DIN-rail kit and wall-mount ear
Switch Specications
Switch Processing
Scheme
Store-and-Forward
Address Table 2K 4K
Buer 4M bits
1.5Mbits SRAM
packet buer
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
3. Hardware Introduction
3.1 Switch Front Panel
The front panel of the Industrial Gigabit Ethernet Switch
consists of 5 or 8 auto-sensing 10/100/1000Mbps Ethernet
RJ45 ports. The LED Indicators are also located on the RJ45
ports of the Gigabit Ethernet Switch.
Figures 3-1 and 3-2 show the front panels of the industrial
Gigabit Ethernet Switches.
P1 P2 Alarm
1
2
3
4
5
1000
10/100
IGS-501T
ACT
LNK
ACT
LNK
ACT
LNK
IGS-801T
ACT
LNK
100
1000
P1 P2 Fault
1
2
3
4
5
6
7
8
Figure 3-1:
IGS-501T Front Panel
Figure 3-2:
IGS-801T Front Panel
IGS-801T:
LED Color Function
P1 Green Lit to indicate power 1 has power.
P2 Green Lit to indicate power 2 has power.
FAULT Red
Lit to indicate either power 1 or power 2
has no power.
1000
LNK/ACT
Green
Lit to indicate the port is successfully
connecting to the network at 1000Mbps.
O to indicate that the port is successfully
connecting to the network at 10Mbps or
100Mbps.
Blinking to indicate that the port is actively
sending or receiving data.
10/100
LNK/ACT
Amber
Lit to indicate the port is successfully
connecting to the network at 100Mbps or
10Mbps.
O to indicate that the port is successfully
connecting to the network at 1000Mbps.
Blinking to indicate that the port is actively
sending or receiving data.
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Gigabit Ethernet Switch is used for two DC redundant
power inputs. Please follow the steps below to insert the power
wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.
1. Insert positive and negative DC power wires into contacts 1
and 2 for Power 1 or 5 and 6 for Power 2.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1.2A max.
AC Input: 24V
, 1.1A max.
V1+ V2+
PWR1
PWR2Alarm
1 2 3 4 5 6