User Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 -
- 14 -
4.3 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the Industrial
Gigabit Ethernet Switch will detect the fault status of the power failure
and then forms an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
1 2 3 4 5 6
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V DC,1A.
Step 2: Lightly insert the bottom of the switch into the track
1
2
Step 3: Make sure the DIN rail is tightly secured on the track.
Step 4: Please refer to the following procedure to remove the
Industrial Gigabit Ethernet Switch from the track.
1
2
Step 5: Lightly pull out the bottom of the switch for removing it from
the track.
5. Installation
This section describes the functionalities of the Industrial Gigabit
Ethernet Switch’s components and guides you to installing it on the DIN
rail and wall. Please read this chapter completely before continuing.
This following picture tells the user how to install the
device, and the device is not IGS-500T.
5.1 DIN-rail Mounting Installation
The DIN rail is screwed on the Industrial Gigabit Ethernet Switch when
out of factory. When replacing the wall-mount application with DIN-rail
application, Industrial Gigabit Ethernet Switch is needed. Please refer to
the following gures to screw the DIN rail on it. To hang the Industrial
Gigabit Ethernet Switch, follow the following steps:
Step 1: Screw the DIN rail on the Industrial Gigabit Ethernet Switch.
5.2 Wall-mount Plate Mounting
To install the Industrial Gigabit Ethernet Switch on the wall, please
follow the instructions described below.
Step 1: To remove the DIN rail from the Industrial Gigabit Ethernet
Switch, loosen the screws.
Step 2: Place the wall-mount plate on the rear panel of the Industrial
Gigabit Ethernet Switch.
Step 3: Use the screws to screw the wall-mount plate on the Industrial
Gigabit Ethernet Switch.
Step 4: Use the hook holes at the corners of the wall-mount plate to
hang the Industrial Gigabit Ethernet Switch on the wall.
Step 5: To remove the wall-mount plate, reverse the steps above.
PLANET TECHNOLOGY CORPORATION
e-mail: [e-mail] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]
EC Declaration of Conformity
For the following equipment:
*Type of Product : Industrial 5-Port 10/100/1000T Compact Gigabit Ethernet Switch
*Model Number : IGS-500T
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2014/30/EU).
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 (2015 + AC:2016)
EN61000-3-2 (2014)
EN61000-3-3 (2013)
EN 55024 (2010 + A1:2015)
Responsible for marking this declaration if the:
 Manufacturer  Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan,
R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
June 28, 2017
Place
Date
Legal Signature
Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
switch support team.
PLANET online FAQs :
http://www.planet.com.tw/en/support/faq.php
Switch support team mail address :
[e-mail]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.