Datasheet

IGS-4215-8P2T2S
8
Specications
Product
IGS-4215-8P2T2S
HardwareSpecications
Copper Ports Ten 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports (Port-1 to Port-10)
SFP Ports
Two 1000BASE-SX/LX/BX SFP interfaces (Port-11 and Port-12)
Compatible with 100BASE-FX SFP
PoE Injector Port Eight ports with 802.3af/802.3at PoE+ injector function (Port-1 to Port-8)
Console 1 x RS232-to-RJ45 serial port (115200,8, N, 1)
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin 5/6 for Power 2
Alarm One relay output for power failure. Alarm relay current carry ability: 1A @ 24V AC
Power Requirements 48~56V DC, 6A (max.) (>51V DC for PoE+ output recommended)
Power Consumption/ Dissipation
7.8 watts, 26BTU (Standby without PoE function) at DC 56V power input
14 watts, 47BTU (Full loading without PoE function) at DC 56V power input
254 watts, 866BTU (Full loading with PoE function) at DC 56V power input
Dimensions (W x D x H) 76.8 x 107.3 x 152 mm
Weight 1040g
Enclosure IP30 aluminum case
Installation DIN-rail kit and wall-mount ear
ESD Protection 6KV DC
LED
3 x LED for System and Power:
■Green:DCPower1
■Green:DCPower2
■Red:PowerFault
2 x LED for PoE Copper Port (Port-1~Port-8):
■Green:LNK/ACT(10/100/1000Mbps)
■Amber:PoE-In-Use
2 x LED for 10/100/1000T Copper Port (Port-9~Port-10):
■Green:1000LNK/ACT
■Amber:10/100LNK/ACT
2 x LED for per mini-GBIC interface (Port-11 and Port-12)
■Green:1000LNK/ACT
■Amber:100LNK/ACT
4 x LED for PoE Power Usage (W) (Low to high)
■Amber:60W,120W,180Wand240W
Switching
Switch Architecture Store-and-Forward
Switch Fabric 24Gbps/non-blocking
Switch Throughput@64 bytes 17.85Mpps @64 bytes
MAC Address Table 8K entries
Shared Data Buffer 4.1 megabits
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame 10 Kbytes
Power over Ethernet
PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply Type End-span
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Output
IEEE 802.3af Standard
- Per port 48V~51V DC (depending on the power supply), max. 15.4 watts
IEEE 802.3at Standard
- Per port 51V~56V DC (depending on the power supply), max. 36 watts
PoE Power Budget Dual power input: maximum 240W (depending on power input)
Max. Number of Class 2 PDs 8
Max. Number of Class 3 PDs 8
Max. Number of Class 4 PDs 8
PoE Management Functions
PoE Management
PD Alive Check
Scheduled Power Recycling
PoE Schedule
PoE Usage Monitoring
PoE Extension