User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.2.1 System Information
- 4.2.2 IP Configurations
- 4.2.3 IPv6 Configuration
- 4.2.4 User Configuration
- 4.2.5 Time Settings
- 4.2.6 Log Management
- 4.2.7 SNMP Management
- 4.2.8 RMON
- 4.2.9 Fault Alarm Configuration
- 4.2.10 Remote Management
- 4.3 Port Management
- 4.3.1 Port Configuration
- 4.3.2 Port Counters
- 4.3.3 Bandwidth Utilization
- 4.3.4 Port Mirroring
- 4.3.5 Jumbo Frame
- 4.3.6 Port Error Disabled Configuration
- 4.3.7 Port Error Disabled Status
- 4.3.8 Protected Ports
- 4.3.9 EEE
- 4.3.10 SFP Module Information
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN Setting Example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 IGMP Snooping
- 4.9 MLD Snooping
- 4.10 LLDP
- 4.11 MAC Address Table
- 4.12 Quality of Service
- 4.13 Security
- 4.14 Ring
- 4.15 Maintenance
- 4.16 Diagnostics
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A Switch's RJ45 Pin Assignments
User’s Manual of IGS-4215 series
26
Per 10/100/1000BASE-T Port
LED Color Function
1000
LNK/ACT
Green
Lights
To indicate the link through that port is successfully established at 1000Mbps.
Blinks
To indicate that the switch is actively sending or receiving data over that port.
10/100
LNK/ACT
Amber
Lights
To indicate the port is successfully established at 10/100Mbps.
Blinks
To indicate that the Switch is actively sending or receiving data over that port.
Per 100/1000BASE-SX/LX/BX SFP Interface
LED Color Function
1000
LNK/ACT
Green
Lights
To indicate the link through that port is successfully established at
1000Mbps
.
Blinks
To indicate that the switch is actively sending or receiving data over that port.
100Mbps
LNK/ACT
Amber
Lights
To indicate the port is running at
100Mbps
and successfully established.
Blinks
To indicate that the switch is actively sending or receiving data over that port.
2.1.4 Switch Upper Panel
The upper panel of the Industrial Managed Switch consists of one terminal block connector within two DC power inputs. Figure
2-1-4 ~6 shows the upper panel of the Industrial Managed Switch.
Figure 2-1-4: IGS-4215-16T2S Top View
Figure 2-1-5: IGS-4215-8T2S Top View
Figure 2-1-6: IGS-4215-4T2S Top View