User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.3 Port Management
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN Setting Example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 Quality of Service
- 4.9 Security
- 4.10 ACL
- 4.11 MAC Address Table
- 4.12 LLDP
- 4.13 Diagnostics
- 4.14 RMON
- 4.15 Power over Ethernet
- 4.16 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A Switch's RJ45 Pin Assignments
User’s Manual of IGS-4215 Series
24
IGS-4215-8P2T2S
Product IGS-4215-8P2T2S
Hardware Specifications
Copper Ports Ten 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports (Port-1 to Port-10)
SFP/mini-GBIC Slots
Two 1000BASE-SX/LX/BX SFP interfaces (Port-11 and Port-12)
Compatible with 100BASE-FX SFP
PoE Injector Port
Eight ports with 802.3af/802.3at PoE+ injector function (Port-1 to Port-8)
Console 1 x RS232-to-RJ45 serial port (115200,8, N, 1)
Switch Architecture Store-and-Forward
Switch Fabric 24Gbps/non-blocking
Switch Throughput@64 bytes
17.85Mpps @64 bytes
MAC Address Table 8K entries
Shared Data Buffer 4.1 megabits
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame
10 Kbytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
LED
3 x LED for System and Power:
Green: DC Power 1
Green: DC Power 2
Red: Power Fault
2 x LED for PoE Copper Port (Port-1~Port-8):
Green: LNK/ACT (10/100/1000Mbps)
Orange: PoE-in-Use
2 x LED for 10/100/1000T Copper Port (Port-9~Port-10):
Green: 1000 LNK/ACT
Orange: 10/100 LNK/ACT
2 x LED for per mini-GBIC interface (Port-11 and Port-12)
Green: 1000 LNK/ACT
Orange: 100 LNK/ACT
4 x LED for PoE Power Usage (W) (Low to high)
Orange: 60W, 120W, 180W and 240W
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for fault alarm; Pin 5/6 for Power 2
Alarm
One relay output for power failure. Alarm relay current carry ability: 1A @ 24V AC
Power Requirements 48~56V DC, 6A (max.) (>51V DC for PoE+ output recommended)
Power Consumption/
Dissipation
7.8 watts, 26BTU (Standby without PoE function) at DC 56V power input
14 watts, 47BTU (Full loading without PoE function) at DC 56V power input