User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web Page
- 4.2 System
- 4.3 Port Management
- 4.4 Link Aggregation
- 4.5 VLAN
- 4.5.1 VLAN Overview
- 4.5.2 IEEE 802.1Q VLAN
- 4.5.3 Management VLAN
- 4.5.4 Create VLAN
- 4.5.5 Interface Settings
- 4.5.6 Port to VLAN
- 4.5.7 Port VLAN Membership
- 4.5.8 Protocol VLAN Group Setting
- 4.5.9 Protocol VLAN Port Setting
- 4.5.10 GVRP Setting
- 4.5.11 GVRP Port Setting
- 4.5.12 GVRP VLAN
- 4.5.13 GVRP Statistics
- 4.5.14 VLAN Setting Example:
- 4.6 Spanning Tree Protocol
- 4.7 Multicast
- 4.8 Quality of Service
- 4.9 Security
- 4.10 ACL
- 4.11 MAC Address Table
- 4.12 LLDP
- 4.13 Diagnostics
- 4.14 RMON
- 4.15 Power over Ethernet
- 4.16 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A Switch's RJ45 Pin Assignments
User’s Manual of IGS-4215 Series
17
1.4 Product Features
Physical Port
■ 8-port 10/100/1000BASE-T Gigabit RJ45 copper with 4-/8-port IEEE 802.3at/af PoE Injector(Port-1 to Port-4/8)
■ 2 100/1000BASE-X mini-GBIC/SFP slots, SFP type auto detection (For IGS-4215-4P4T2S/IGS-4215-8P2T2S)
■ RJ45 console interface for switch basic management and setup
Power over Ethernet
■ Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE
■ Backward compatible with IEEE 802.3af Power over Ethernet
■ Up to 4/8 ports of IEEE 802.3af/802.3at devices powered
■ 144-watt PoE budget (IGS-4215-4P4T/IGS-4215-4P4T2S)
■ 240-watt PoE budget (IGS-4215-8P2T2S)
■ Supports PoE power up to 36 watts for each PoE port
■ Auto detects powered device (PD)
■ Circuit protection prevents power interference between ports
■ Remote power feeding up to 100 meters
■ PoE management
− Total PoE power budget control
− Per port PoE function enable/disable
− PoE port power feeding priority
− Per PoE port power limitation
− PD classification detection
− PD alive check
− PoE schedule
Industrial Case and Installation
■ IP30 aluminum case
■ DIN-rail and wall-mount design
■ Supports -40 to 75 degrees C operating temperature
■ Supports Ethernet ESD protection of 6KV DC power
■ Redundant power design
− 48V~56V DC wide power input
Switching
■ Hardware based 10/100Mbps (half/full duplex), and 1000Mbps (full duplex) mode, flow control and auto-negotiation
and auto MDI/MDI-X
■ Features Store-and-Forward mode with wire-speed filtering and forwarding rates
■ IEEE 802.3x flow control for full duplex operation and back pressure for half duplex operation
■ 8K MAC address table size
■ 10K jumbo frame
■ Automatic address learning and address aging
■ Supports CSMA/CD protocol