User's Manual

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.Installation
This section describes the functionalities of the Industrial
Ethernet Switch’s components and guides you to installing it
on the DIN rail and wall. Please read this chapter completely
before continuing.
Note
This following pictures show how to install the device.
However, the device in the picture is not IGS-1600T
or IGS-1820TF.
3.1 DIN-railMountingInstallation
1
2
3.2 Wall-mountPlateMounting
Flow Control
IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
ESD Protection 6KV DC
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power
input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm,
Pin 5/6 for Power 2
Alarm
One relay output for power failure. Alarm relay
current carry ability: 1A @ 24V DC
Dimensions
(W x D x H)
66 x 107 x 152 mm 66 x 107 x 152 mm
Weight 743g 745g
Power
Requirements
Dual DC 12~48V, AC 24V
Power
Consumption
DC input:
Max. 3.4 watts/
11.6BTU
(System on)
Max. 8.7 watts/
29.7BTU
(Full loading)
DC input:
Max. 3.4 watts/
11.6BTU
(System on)
Max. 11.1 watts/
37.9BTU
(Full loading)
AC input:
Max. 5 watts/17BTU
(System on)
Max. 13.99 watts/
47.8BTU
(Full loading)
AC input:
Max. 6 watts/20.5BTU
(System on)
Max. 15 watts/51.2BTU
(Full loading)
3.3 SideWall-mountPlateMounting
4.ProductSpecications
Product
IGS-1600T
IGS-1820TF
Hardware Specifications
Gigabit Ethernet
Copper Ports
16 10/100/1000BASE-T RJ45 auto-MDI/MDI-X
ports
Gigabit SFP
Slots
--
Two 1000BASE-SX/LX/
BX SFP interfaces
Switch
Architecture
Store-and-Forward
Switch Fabric
32Gbps (non-blocking) 36Gbps (non-blocking)
Throughput
(packet per
second)
23.81Mpps@ 64 bytes 26.79Mpps@ 64 bytes
Address Table
8K entries, automatic source address learning
and aging
Shared Data
Buffer
4.1Mbits
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-
TX
IEEE 802.3ab
1000BASE-T
IEEE 802.3x flow
control and back
pressure
IEEE 802.1p Class of
Service
IEEE 802.3az Energy
Efficient Ethernet
(EEE)
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-
TX
IEEE 802.3ab
1000BASE-T
IEEE 802.3z
1000BASE-SX/LX
IEEE 802.3x flow
control and back
pressure
IEEE 802.1p Class of
Service
IEEE 802.3az Energy
Efficient Ethernet
(EEE)
Environment
Operating
Temperature
-40 ~ 75 degrees C
Storage
Temperature
-40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
5.CustomerSupport
Thank you for purchasing PLANET products. You can browse
our online FAQ resource on PLANET web site rst to check if it
could solve your issue. If you need more support information,
please contact PLANET switch support team.
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq
Switch support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2019.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
FCCWarning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment
is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with this user’s guide,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
CEMarkWarning
This device is compliant with Class A of CISPR 32. In a
residential environment this equipment may cause radio
interference.
WEEEWarning
To avoid the potential eects on the environment and
human health as a result of the presence of
hazardous substances in electrical and electronic
equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.