Industrial 8-Port 10/100/1000BASE-T + 2-Port 100/1000BASE-X SFP Ethernet Switch IGS-1020TF User’s Manual
Table Of Contents 1. Package Contents.............................................................. 3 2. Hardware Introduction....................................................... 4 2.1 Physical Dimensions................................................. 4 2.2 Switch Front Panel................................................... 5 2.3 LED Indicators......................................................... 6 2.4 Switch Upper Panel.................................................. 8 2.
1. Package Contents Thank you for purchasing PLANET industrial 10-port Gigabit Ethernet Switch, IGS-1020TF. In the following section, the term “Industrial Gigabit Ethernet Switch” means the IGS-1020TF. Open the box of the Industrial Gigabit Ethernet Switch and carefully unpack it.
Bottom View V1+ V1- 4 PWR1 Fault V2+ V2- PWR2 Input DC12~48V, AC 24V ACT ACT 4 2 3 1 IGS-1020TF 6 ACT 10 8 ACT LNK 1000 10/100 LNK 100/1000X SFP 10 P2 FAULT 5 9 100 LNK 1000 LNK 7 P1 Front View 1 2 3 4 5 6 9 Side View Top View Rear View DIN-Rail Kit Dimensions ( unit = mm ) Mounting Kit Mounting Kit 2. Hardware Introduction 2.1 Physical Dimensions IGS-1020TF Industrial Gigabit Ethernet Switch dimensions (W x D x H): 135 x 87.
2.2 Switch Front Panel The front panel of the Industrial Gigabit Ethernet Switch consists of 8 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports and 2 dual speed 100/1000BASE-X SFP slots. The LED Indicators are also located on the RJ45 ports and SFP slots of the Gigabit Ethernet Switch. Figure 2-1 shows the front panel of Industrial Gigabit Ethernet Switch.
2.3 LED Indicators System LED Color Function P1 Green Lit: indicates power 1 has power. P2 Green Lit: indicates power 2 has power. FAULT Red Lit: indicates either power 1 or power 2 has no power. Per 10/100/1000T Port LED Color Function 100 LNK/ACT Lit: indicates the link through that port is successfully established at 100Mbps or 10Mbps. Blinking: indicates that the Switch is Orange actively sending or receiving data over that port.
Per 100 / 1000X SFP Slot LED Color Function 100 LNK/ACT Lit: indicates the link through that port is successfully established at 100Mbps. Blinking: indicates that the Switch is Orange actively sending or receiving data over that port. Off: indicates the link through that port is successfully established at 1000Mbps. 1000 LNK/ACT Lit: indicates the link through that port is successfully established at 1000Mbps or 10Mbps.
2.4 Switch Upper Panel The upper panel of the Industrial Gigabit Ethernet Switch consists of one terminal block connector within two DC power inputs, Figure 2-2 shows the upper panel of the Industrial Gigabit Ethernet Switch. 1 2 3 4 5 6 V1+ V1PWR1 V2+ V2Fault PWR2 Input DC12~48V, AC 24V Figure 2-2: Industrial Gigabit Ethernet Switch Upper Panel 2.
1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. 1 2 3 4 5 6 V1+ V1PWR1 V2+ V2Fault PWR2 Input DC12~48V, AC 24V 2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 + - 3 4 Fault 5 6 Power 2 + - 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2. The DC power input range is 12V ~ 48V DC.
2.6 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Gigabit Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.
SFP/mini-GBIC Slots 2 1000BASE-SX/LX/BX SFP interfaces (Port-9 and Port-10) Compatible with 100BASE-FX SFP Switch Processing Scheme Store-and-Forward Switch Fabric 20Gbps (non-blocking) Switch Throughput (packet per second) 14.88Mpps@64bytes MAC Address Table 4K entries Flow Control Back pressure for half duplex IEEE 802.
ESD Protection 6KV DC Enclosure IP30 type metal case Installation DIN rail kit and wall mount ear Dimensions (W x D x H) 56 x 87 x 135 mm Weight 540g Power Requirements DC 12~48V or AC 24V Redundant power with polarity reverses protection function Power Consumption/ Dissipation 8.7watts/29.69BTU 10BASE-T: 2-pair UTP Cat. 3, 4, 5, up to 100 meters 100BASE-TX: 2-pair UTP Cat. 5, 5e up to Twisted-pair 100 meters 1000BASE-T: 4-pair UTP Cat.
Standards Conformance Standards Compliance IEEE 802.3 Ethernet/10BASE-T IEEE 802.3u Fast Ethernet/100BASE-TX IEEE 802.3ab Gigabit Ethernet/1000BASE-T IEEE 802.3z Gigabit Ethernet/1000BASE-SX/LX IEEE 802.3x Full-Duplex Flow Control IEEE 802.3az Energy Efficient Ethernet (EEE) IEEE 802.
3. Installation This section describes the functionalities of the Industrial Gigabit Ethernet Switch’s components and guides how to install it on the DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. Note This following picture is telling the user how to install the device, and the device is not IGS1020TF. 3.1 DIN-rail Mounting Installation The DIN-rail is screwed on the Industrial Gigabit Ethernet Switch when out of factory.
Step 2: Lightly insert the bottom of the switch into the track 1 2 Step 3: Make sure if the DIN-Rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial Gigabit Ethernet Switch from the track.
Step 5: Lightly pull out the bottom of the switch for removing it from the track. 3.2 Wall-mount Plate Mounting To install the Industrial Gigabit Ethernet Switch on the wall, please follow the instructions described below. Step 1: To remove the DIN-Rail from the Industrial Gigabit Ethernet Switch, loosen the screws to remove the DIN-rail. Step 2: Place the wallmount plate on the rear panel of the Industrial Gigabit Ethernet Switch.
3.3 Installing the SFP Transceiver The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Industrial Gigabit Ethernet Switch as Figure 2-3 shows. MGB/MFB Series Module Figure 3-1: Plug-in the SFP Transceiver PLANET Industrial Gigabit Ethernet Switch supports 100/1000 dual mode with both single mode and multi-mode SFP transceivers. 1.
2. Check whether the fiber-optic cable type matches with the SFP transceiver requirement. To connect to 1000BASE-SX SFP transceiver, please use the multi-mode fiber cable with one side being the male duplex LC connector type. To connect to 1000BASE-LX or 1000BASE-BX SFP transceiver, please use the single-mode fiber cable with one side being the male duplex LC connector type. Connect the Fiber Cable 1. Insert the duplex LC connector into the SFP transceiver. 2.
3.4 Removing the Transceiver Module 1. Make sure there is no network activity by consulting or checking with the network administrator. Or through the management interface of the switch/converter (if available) to disable the port in advance. 2. Remove the Fiber Optic Cable gently. 3. Turn the lever of the MGB/MFB module to a horizontal position. 4. Pull out the module gently through the lever.
4. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Gigabit Ethernet Switch is not functioning properly, make sure the Industrial Gigabit Ethernet Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Gigabit Ethernet Switch. Per port LED is lit, but the traffic is irregular Solution: Check whether the attached device is not set to dedicated full duplex.
APPENDIX A: Networking Connection A.
A.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
A.3 Fiber Optic Cable Connection Parameter The wiring details are shown below: 100FX Fiber Optic Cables: Standard Fiber Type Cable Specifications 100BASE-FX (1300nm) Multi-mode 50/125μm or 62.5/125μm 100BASE-FX (1310nm) Multi-mode 50/125μm or 62.5/125μm Single-mode 9/125μm 100BASE-BX-U (TX:1310/RX:1550) 100BASE-BX-D (TX:1550/RX:1310) Single-mode 9/125μm 1000X Fiber Optic Cables: Standard Fiber Type Cable Specifications 1000BASE-SX (850nm) Multi-mode 50/125μm or 62.
Wiring Distances: Diameter (micron) Modal Max. Distance Bandwidth (meters) (MHz * km) 1000BASE- SX MM 62.5 62.5 50 50 100 200 400 500 220 275 500 550 62.
APPENDIX B: Approved PLANET SFP Transceivers The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules MGB-GT SFP-Port 1000BASE-T Module - 100m MGB-SX SFP-Port 1000BASE-SX mini-GBIC module - 550m MGB-SX2 SFP-Port 1000BASE-SX mini-GBIC module – 2km MGB-LX SFP-Port 1000BASE-LX mini-GBIC module - 10km MGB-L30 SFP-Port 1000BASE-LX mini-GBIC module - 30km MGB-L50 SFP-Port 1000BASE-LX mini-GBIC module - 50km MGB-L70 SFP-Port 1000BAS
MGB-LA60 SFP-Port 1000BASE-LX (WDM, TX:1310nm) miniGBIC module - 60km MGB-LB60 SFP-Port 1000BASE-LX (WDM, TX:1550nm) miniGBIC module - 60km MGB-TSX SFP-Port 1000BASE-SX mini-GBIC module - 550m (-40~75°C) MGB-TLX SFP-Port 1000BASE-LX mini-GBIC module - 10km (-40~75°C) MGB-TL30 SFP-Port 1000BASE-LX mini-GBIC module - 30km (-40~75°C) MGB-TL70 SFP-Port 1000BASE-LX mini-GBIC module - 70km (-40~75°C) MGB-TLA10 SFP-Port 1000BASE-LX (WDM, TX:1310nm) miniGBIC module - 10km (-40~75°C) MGB-TLB10 SFP-Por
Fast Ethernet SFP Transceiver Modules MFB-FX SFP-Port 100BASE-FX Transceiver (1310nm) - 2km MFB-F20 SFP-Port 100BASE-FX Transceiver (1310nm) 20km MFB-F40 SFP-Port 100BASE-FX Transceiver (1310nm) 40km MFB-F60 SFP-Port 100BASE-FX Transceiver (1310nm) 60km MFB-F120 SFP-Port 100BASE-FX Transceiver (1550nm) 120km MFB-FA20 SFP-Port 100BASE-BX Transceiver (WDM, TX:1310nm) - 20km MFB-FB20 SFP-Port 100BASE-BX Transceiver (WDM, TX:1550nm) - 20km MFB-TFX SFP-Port 100BASE-FX Transceiver (1310nm) - 2km (-
