User's Manual

- 9 -
- 10 -
- 11 - - 13 -
- 12 - - 14 - - 15 -
1 2 3 4 5 6
Fault Alarm Contacts
The Fault Alarm Contacts are energized (CLOSE) for
normal operation and will OPEN when failure occurs
Fault
Insert the wires into the fault alarm contacts
Note
1. The wire gauge for the terminal block should be in the
range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V with a maximum
current of 1A.
2.6 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
Earth Ground
PWR1
PWR2
Fault
DC Input:
48-56V , 6A max.
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Note
EMD (Lightning) DAMAGE IS NOT CONVERED UNDER
WARRANTY.
3.3 Side Wall-mount Plate Mounting
(for IGS-1020PTF only)
4.ProductSpecications
Model IGS-1020PTF IGS-1020PTF-12V
Hardware Specications
Copper Ports 8 10/100/1000BASET RJ45 auto-MDI/MDI-X ports
PoE Injector
Ports
8 ports with 802.3at PoE+ injector function
(Port 1 to Port 8)
SFP Slots
2 1000BASE-SX/LX/BX SFP interfaces
(Port 9 and Port 10)
Compatible with 100BASE-FX SFP
Connector
Removable 6-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for fault alarm;
Pin 5/6 for Power 2
DIP Switch
Standard/Extend mode
(Extend mode for Port 5 to Port 8 only)
3. Installation
This section describes the functionalities of the Industrial PoE+ Switch’s
components and guides you to installing it on the DIN-rail and wall.
Basic knowledge of networking is assumed. Please read this chapter
completely before continuing.
Note
The installation procedures of the IGS-1020PTF and IGS-
1020PTF-12V are the same as they are shown below.
3.1 DIN-rail Mounting Installation
3.2 Wall-mount Plate Mounting
LED Indicators
3 x LED for System and Power:
 Green: DC Power 1
 Green: DC Power 2
 Red: Power Fault Alarm
8 x LED for PoE Copper Port (Port 1 to Port 8):
 Green: LNK/ACT (10/100/1000Mbps)
 Amber: PoE-in-Use
2 x LED for 100/1000X Fiber Port (Port 9 to Port 10):
 Green: LNK/ACT (100/1000Mbps)
 Amber: 1000Mbps
4 x LED for PoE Usage
 Amber: 60W, 120W, 180W and 240W
Power
Requirements
48~56V DC, 6A (max.) 12~56V DC, 6A (max.)
Power
Consumption
Max. 3.92
watts/13BTU@56V DC
input (System)
Max. 7.28
watts/24BTU@56V DC
input (Ethernet Full
Loading)
Max. 251.2
watts/857BTU@56V DC
input (Ethernet + PoE Full
Loading)
Max. 5.6
watts/19BTU@56V DC
input (System)
Max. 8.4
watts/29BTU@56V DC
input (Ethernet Full
Loading)
Max. 252.1
watts/860BTU@56V DC
input (Ethernet + PoE Full
Loading)
Dimensions
(W x D x H)
66 x 106 x 152 mm 77 x 106 x 152mm
Weight 879g 1164g
Enclosure IP30 metal case IP30 aluminum case
Installation
DIN-rail/wall-mount/side
wall-mount
DIN-rail/wall-mount
ESD Protection 6KV
Switch Specications
Switch
Architecture
Store-and-Forward
Switch Fabric 20Gbps
Throughput
(packet per
second)
14.8Mpps@64bytes
Address Table 8K entries
Buer Memory 4M bits on-chip buer memory
Jumbo Frame 9Kbytes
Flow Control
Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Power over Ethernet
PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power
Supply Type
End-span
Power Pin
Assignment
1/2 (+), 3/6 (-)
PoE Power
Output
Per port 48~56V DC
Max. 30 watts
Per port 54V DC
Max. 30 watts
PoE Power
Budget (max.)
240W maximum
240W maximum@54V DC
120W maximum@24V DC
60W maximum@12V DC
Max. Number
of Class 3
PDs@25W
8
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability
Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet over Fiber Optic
IEEE 802.3az Energy Ecient Ethernet (EEE)
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3af Power over Ethernet
Environment
Temperature
Operating: -40~75 degrees C
Storage: -40~85 degrees C
Humidity
Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
5. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource at the PLANET Web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=3
Support team mail address:
[e-mail]
Copyright © PLANET Technology Corp. 2020.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.