User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial 8-port 10/100/1000T
802.3at PoE + 2-port 100/1000X SFP Ethernet Switch, IGS-1020PTF
or IGS-1020PTF-12V. The hardware specications of these models are
shown below:
Model Name
10/100/1000T 802.3at
PoE+ RJ45 Ports
100/1000X
SFP Slots
Power Input
Range
IGS-1020PTF
8 2
DC 48~56V
IGS-1020PTF-12V DC 12~56V
In the following sections, the term “Industrial PoE+ Switch” means
the IGS-1020PTF or IGS-1020PTF-12V.
Open the box of the Industrial PoE+ Switch and carefully unpack it. The
box should contain the following items:
Industrial PoE+ Switch x 1 User’s manual x 1
Wall-mount kit x 1 DIN-rail kit x 1
RJ45 Dust Caps x 8 SFP Dust Caps x 2
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
Gigabit SFP Slots (Port 9 to Port 10)
100/1000BASE-X mini-GBIC slot, SFP (small factor pluggable)
transceiver module: From 550 meters (multi-mode ber) to
10/20/30/40/50/60/70/120 kilometers (single-mode ber).
DIP Switch for Port 5 to Port 8
The Industrial PoE+ Switch has a built-in solid DIP switch that
provides “Standard” and “Extend” operation modes. The Industrial
PoE+ Switch operates as a normal IEEE 802.af/at PoE+ Switch in the
“Standard” operation mode.
In the “Extend” operation mode, Port 5 to Port 8 of the Industrial PoE+
Switch operates on a per-port basis at 10Mbps full duplex operation but
can support 20~25-watt PoE power output over a distance of up to 250
meters overcoming the 100m limit on Ethernet UTP cable. With this
brand-new feature, the Industrial PoE+ Switch provides an additional
solution for 802.3af/at PoE+ distance extension.
Standard Mode (default)
PoE IP Camera
PoE
100 meters (328 feet)
PoE
100BASE-TX UTP with PoE
IGS-1020PTF
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
Extended Mode
PoE
250 meters (820 feet)
PoE
10BASE-T UTP with PoE
PoE IP Camera
IGS-1020PTF
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
Figure 2-4 shows the upper panel of the IGS-1020PTF-12V.
PWR1
PWR2
Fault
Max. fault loading: 24V, 1A
DC Input:
12-56V , 6A max.
1 2 3 4 5 6
Figure 2-4: IGS-1020PTF-12V Upper Panel
2.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial
PoE+ Switch is used for two DC redundant power inputs. Please follow
the steps below to insert the power wire.
Caution
When performing any of the procedure like inserting the
wires or tightening the wire-clamp screws, make sure the
power is OFF to prevent from getting an electric shock.
1. Insert positive and negative DC power wires into Contacts 1 and 2
for Power 1, or Contacts 5 and 6 for Power 2.
PWR1
PWR2
Fault
DC Input:
48-56V , 6A max.
Max. fault loading: 24V, 1A
1 2 3 4 5 6
60W Amber
O: Indicates the PoE usage is less than 30W.
Blinks: Indicates that the PoE usage is around 30W
to 59W.
Lights: Indicates the PoE usage is around/over 60W.
120W Amber
Blinks: Indicates that the PoE usage is around 60W
to 119W.
Lights: Indicates the PoE usage is around/over
120W.
180W Amber
Blinks: Indicates that the PoE usage is around 120W
to 179W.
Lights: Indicates the PoE usage is around/over
180W.
240W Amber
Blinks: Indicates that the PoE usage is around 180W
to 239W.
Lights: Indicates the PoE usage is at the maximum.
Per 802.3at PoE+ 10/100/1000BASE-T Interface
(Port 1 to Port 8)
LED Color Function
LNK/
ACT
Green
Lights: Indicates the link through that port is
successfully established at 10Mbps, 100Mbps or
1000Mbps.
Blinks: Indicates that the switch is actively sending
or receiving data over that port.
PoE -
in-Use
Amber
Lights: Indicates the port is providing DC in-line
power.
O: Indicates the connected device is not a PoE
powered device (PD).
2. Hardware Introduction
2.1 Switch Front Panel
The front panels of the Industrial PoE+ Switches consist of Ethernet
interfaces and LED indicators as shown below:
9 10
9 10
100/1000X SFP
LNK ACT
1000
10/100/1000T
IGS-1020PTF
6
4
2
7
5
3
1
8
LNK
ACT
PoE-in-Use
802.3at PoE+
P1 P2 Fault
240W
PoE Usage
180W
120W
60W
Standard Extend (Ports 5~8)
Mode
9 10
9 10
100/1000X SFP
LNK ACT
1000
10/100/1000T
IGS-1020PTF-12V
6
4
2
7
5
3
1
8
LNK
ACT
PoE-in-Use
802.3at PoE+
P1 P2 Fault
240W
PoE Usage
180W
120W
60W
Standard Extend (Ports 5~8)
Mode
Figure 2-1:
IGS-1020PTF front panel
Figure 2-2:
IGS-1020PTF-12V front panel
Gigabit TP Interfaces (Port 1 to Port 8)
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters in
standard mode.
DIP Switch Mode Function
Standard
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
DIP switch is o
This mode makes the Industrial PoE+ Switch
operate as a general switch and all PoE ports
operate at 10/100/1000Mbps auto-negotiation.
Extended
100/1000X SFP
10/100/1000T
Standard Extend (Ports 5~8)
Mode
DIP switch is on
This mode makes Port 5 to Port 8 of the
Industrial PoE+ Switch operate on a per-port
basis at 10Mbps full duplex operation but can
support PoE power output over a distance of
up to 250 meters overcoming the 100m limit
on Ethernet UTP cable.
*Note: After changing the DIP switch mode, please reboot the switch
to take eect.
2.2 LED Indicators
System
LED Color Function
P1 Green Lights: Indicates power 1 has power.
P2 Green Lights: Indicates power 2 has power.
FAULT Red
Lights: Indicates either power 1 or power 2 has no
power.
Per 100/1000X SFP Slot (Port 9 to Port 10)
LED Color Function
LNK/
ACT
Green
Lights: Indicates the link through that port is
successfully established at 1000Mbps or 100Mbps.
Blinks: Indicates that the switch is actively sending
or receiving data over that port.
1000 Amber
Lights: Indicates the link through that port is
successfully established at 1000Mbps.
O: Indicates the link through that port is not
established or is established at 100Mbps.
2.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one terminal
block connector within two power input and one relay output.
Figure 2-3 shows the upper panel of the IGS-1020PTF.
PWR1
PWR2
Fault
DC Input:
48-56V , 6A max.
Max. fault loading: 24V, 1A
1 2 3 4 5 6
Figure 2-3: IGS-1020PTF Upper Panel
2. Tighten the wire-clamp screws for preventing the wires from loos-
ening.
1 2 3 4 5 6
Power 1 Fault Power 2
+ - + -
Note
1. The wire gauge for the terminal block should be in the
range between 12 ~ 24 AWG.
2. The IGS-1020PTF-12V supports DC input range of
12V to 56V. To avoid damage, please use the IGS-
1020PTF-12V under its specification.
DC Input Max. PoE Budget
12V 60W
24V 120W
48V 240W
2.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. Inserting the wires, the Industrial
PoE+ Switch will detect the fault status of the power failure and then
forms an open circuit. The following illustration shows an application
example for wiring the fault alarm contacts.