Industrial L2+ Multi-Port Full Gigabit Managed Ethernet Switch IGS-10020MT/IGS-10020PT/HPT/IGS-10080MFT IGS-12040MT/IGS-20040MT/IGS-20160HPT Quick Installation Guide
Table of Contents 1. Package Contents........................................................................................ 3 2. Requirements.............................................................................................. 5 3. Wiring the Power Inputs............................................................................... 6 4. Terminal Setup...........................................................................................10 5. Logon to the Console.............................
1. Package Contents Thank you for purchasing PLANET L2+ Industrial Managed Switch, IGS-10020 Series/IGS-10080MFT/IGS-12040MT/IGS-20040MT/IGS-20160HPT. The descriptions of these models are as follows: IGS-10020MT Industrial 8-Port 10/100/1000T + 2-Port 100/1000X SFP Managed Switch IGS-10020PT Industrial 8-Port 10/100/1000T 802.3af PoE + 2-Port 100/1000X SFP Managed Switch IGS-10020HPT Industrial 8-Port 10/100/1000T 802.
Open the box of the Industrial Managed Switch and carefully unpack it.
2. Requirements The Industrial Managed Switch provides remote login interface for management purposes. The following equipment is necessary for further management: Workstation is installed with Ethernet NIC (Network Interface Card) Choice of Internet browsers includes Windows XP/2003, Vista, Windows 7, Windows 8, Windows 10, MAC OS X, Linux, Fedora, Ubuntu or other platforms compatible with TCP/IP protocols. The above workstation is installed with Web browser and JAVA runtime environment plug-in.
3. Wiring the Power Inputs The Upper Panel of the Industrial Managed Switch indicates a DC inlet power socket and consists of one terminal block connector within 6 contacts. Please follow the steps below to insert the power wire. 1. Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5 and 6 for Power 2.
IGS-10080MFT: 12~48V DC, 24V AC V2- V2+ V1- V1+ 1A@24V PWR2 Fault PWR1 Input DC 12V~48V Figure 3-3: IGS-10080MFT Upper Panel IGS-12040MT: 12~72V DC, 24V AC DC2 Fault DC1 Input DC 12-72V AC 24V GND GND DO 1 DI 0 DI 1 DO 0 Figure 3-4: IGS-12040MT Upper Panel 7
IGS-20040MT: 9~48V DC, 24V AC Figure 3-5: IGS-20040MT Upper Panel IGS-20160HPT: 48V~56V DC DI 0 DI 1 DO 0 DO 1 GND GND DC1 Fault DC2 Input DC 48-56V Figure 3-6: IGS-20160HPT Upper Panel 8
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 3 4 5 6 Power 2 Positive (+) Pin Negative (-) Pin IGS-10020MT Pin 2 / 6 Pin 1 / 5 IGS-10020PT Pin 1 / 5 Pin 2 / 6 IGS-10020HPT Pin 1 / 5 Pin 2 / 6 IGS-10080MFT Pin 1 / 5 Pin 2 / 6 IGS-12040MT Pin 1 / 5 Pin 2 / 6 IGS-20040MT Pin 1 / 5 Pin 2 / 6 IGS-20160HPT Pin 1 / 5 Pin 2 / 6 Note The wire gauge for the terminal block should be in the range from 12 to 24 AWG.
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type serial (console) port of the Managed Industrial Switch. The console port of the Industrial Managed Switch is DCE already, so that you can connect the console port directly through PC without the need of null modem. IGS Industrial Managed Switch PC/Workstation with Terminal emulation software IP Address: 192.168.0.
5. Logon to the Console Once the terminal has been connected to the device, power on the Industrial Managed Switch and the terminal will display “running testing procedures”. 1. There are six switches with RJ45 type console connector. (IGS10020PT/IGS-10020HPT/IGS-10080MFT/IGS-12040MT/IGS20040MT/IGS-20160HPT) Note 2. Let’s take IGS-20040MT for example. When the following dialog box shown in Figure 5-1 appears, please enter the factory default user name “admin” and password “admin”.
6. Configuring IP address The Industrial Managed Switch is shipped with default IP address shown below: IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 To check the current IP address or modify a new IP address for the Switch, please use the procedure as follows: Display of the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. 2. The screen displays the current IP address shown in Figure 6-1.
Configuration of the IP Address 3. At the “#” prompt, enter the following command and press as shown in Figure 6-2. IGS-20040MT# configure terminal IGS-20040MT (config)# interface vlan 1 IGS-20040MT (config-if-vlan)# ip address 192.168.1.100 255.255.255.0 The previous command would apply the following settings for the Industrial Managed Switch. IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 Figure 6-2: Configuring IP Address Screen 4. Repeat step 1 to check if the IP address has changed.
Store the current switch configuration 5. At the “#” prompt, enter the following command and press . # copy running-config startup-config Figure 6-3: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Managed Switch through the new IP address.
7. Starting Web Management The following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. For example, the default IP address of the Industrial Managed Switch is 192.168.0.100, then the manager PC should be set to 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
3. After entering the password, the main screen appears as shown in Figure 7-3. Figure 7-3: Web Main Screen of Industrial Managed Switch 4. The Switch Menu on the left of the Web page lets you access all the functions and status the Industrial Managed Switch provides. Now, you can use the Web management interface to continue the Switch management. Please refer to the user manual for more. Note 16 For security reason, please change and memorize the new password after this first setup.
8. Resetting the Switch to Default To reset the IP address to the default IP address “192.168.0.100” and the user password to factory default mode (default password is admin), press the hardware reset button on the front panel for about 10 seconds. After the device is rebooted, you can login the management Web interface within the same subnet of 192.168.0.xx and default password. Be noted that all the previous setups will be disappeared after the factory default reset is made. P1 P2 FAULT Ring 9 10 R.
Reset Button Figure 8-3: IGS-10080MFT Reset Button Reset Button 7 8 5 6 3 4 1 2 RESET 1000 LNK ACT 100 LNK ACT IGS-12040MT Figure 8-4: IGS-12040MT Reset Button 18
Reset Button RESET P1 P2 FAULT Ring R.O. 1 2 3 4 5 6 Console 17 Figure 8-5: IGS-20040MT Reset Button 802.3at PoE+ P1 P2 FAULT Ring R.O.
9. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ: http://www.planet.com.tw/en/support/faq.php Switch support team mail address: support_switch@planet.com.tw IGS-10020MT/IGS-10020PT/IGS-10020HPT/IGS-10080MFT/IGS-12040MT/IGS20040MT/IGS-20160HPT User’s Manual: http://www.planet.com.
