(V3) User Manual
Table Of Contents
- 1. INTRODUCTION
- 2. INSTALLATION
- 3. SWITCH MANAGEMENT
- 4. WEB CONFIGURATION
- 4.1 Main Web page
- 4.2 System
- 4.2.1 Management
- 4.2.1.1 System Information
- 4.2.1.2 IP Configuration
- 4.2.1.3 IP Status
- 4.2.1.4 Users Configuration
- 4.2.1.5 Privilege Levels
- 4.2.1.6 NTP Configuration
- 4.2.1.6.1 System Time Correction Manually
- 4.2.1.7 Time Configuration
- 4.2.1.8 UPnP
- 4.2.1.9 DHCP Relay
- 4.2.1.10 DHCP Relay Statistics
- 4.2.1.11 CPU Load
- 4.2.1.12 System Log
- 4.2.1.13 Detailed Log
- 4.2.1.14 Remote Syslog
- 4.2.1.15 SMTP Configuration
- 4.2.1.16 Fault Alarm
- 4.2.1.17 Digital Input/Output
- 4.2.2 Simple Network Management Protocol
- 4.2.3 RMON
- 4.2.4 DHCP server
- 4.2.5 Industrial Protocol
- 4.2.1 Management
- 4.3 Switching
- 4.3.1 Port Management
- 4.3.2 Link Aggregation
- 4.3.3 VLAN
- 4.3.3.1 VLAN Overview
- 4.3.3.2 IEEE 802.1Q VLAN
- 4.3.3.3 VLAN Port Configuration
- 4.3.3.4 VLAN Membership Status
- 4.3.3.5 VLAN Port Status
- 4.3.3.6 Private VLAN
- 4.3.3.7 Port Isolation
- 4.3.3.8 VLAN setting example:
- 4.3.3.8.1 Two Separate 802.1Q VLANs
- 4.3.3.8.2 VLAN Trunking between two 802.1Q aware switches
- 4.3.3.8.3 Port Isolate
- 4.3.3.9 MAC-based VLAN
- 4.3.3.10 IP Subnet-based VLAN Membership Configuration
- 4.3.3.11 Protocol-based VLAN
- 4.3.3.12 Protocol-based VLAN Membership
- 4.3.4 Spanning Tree Protocol
- 4.3.5 Multicast
- 4.3.6 MLD Snooping
- 4.3.7 MVR (Multicast VLAN Registration)
- 4.3.8 LLDP
- 4.3.9 MAC Address Table
- 4.3.10 Loop Protection
- 4.3.11 UDLD
- 4.3.12 GVRP
- 4.3.13 PTP
- 4.4 Quality of Service
- 4.5 Security
- 4.6 Power over Ethernet
- 4.7 Ring
- 4.8 ONVIF
- 4.9 Maintenance
- 5. SWITCH OPERATION
- 6. TROUBLESHOOTING
- APPENDIX A: Networking Connection
- APPENDIX B : GLOSSARY
User’s Manual of IGS PoE series
20
1.5 Product Specifications
Product IGS-10020PT IGS-10020HPT IGS-20160HPT
Hardware Specifications
Version
3 3 2
Copper Ports 8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
18 10/100/1000BASE-T
RJ45 auto-MDI/MDI-X ports
SFP/mini-GBIC Slots
2 1000BASE-SX/LX/BX SFP interfaces (Port-9 and
Port-10)
Compatible with 100BASE-FX SFP
2 1000BASE-SX/LX/BX
SFP interfaces (Port-19 and
Port-20)
Compatible with
100BASE-FX SFP
PoE Injector Port
8 ports with 802.3at/af PoE injector function with Port-
1 to
Port-8
16 ports with 802.3at/af
PoE injector function with
Port-1 to Port-16
Console
1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Switch Architecture
Store-and-Forward
Switch Fabric 20Gbps/non-blocking 40Gbps/non-blocking
Throughput (packet per second)
14.8Mpps@ 64Bytes packet 29.7Mpps@ 64Bytes packet
Address Table
8K entries, automatic source address learning and aging
Shared Data Buffer
4Mbits
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
Jumbo Frame
9Kbytes
Reset Button
< 5 sec: System reboot
> 5 sec: Factory default
ESD Protection
6KV DC
Enclosure IP30 aluminum case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2
Removable 6-pin terminal block for DI/DO interface
Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm
One relay output for power failure. Alarm Relay current carry ability: 1A @ DC 24V
DI/DO
2 Digital Input (DI): Level 0: -24V~2.1V (±0.1V)
Level 1: 2.1V~24V (±0.1V)
Input Load to 24V DC, 10mA max.
2 Digital Output (DO): Open collector to 24V DC, 100mA max.
Dimensions (W x D x H)
72 x 107x 152 mm
84 x 107 x 152 mm
Weight
1032g
1096g
1533g
Power Requirements
DC 48V ~ 56V
DC 12-48V
Dual 48~56V DC
Power Consumption 255 watts max., 870BTU (Full loading with PoE function)
11.1 watts/37.87BTU
(Power on without any
connection)
349 watts/119.08BTU (Full
loading with PoE function)