Datasheet

IGS-10020HPT
2
Digital Input and Digital Output
• 2 Digital Input (DI)
• 2 Digital Output (DO)
• Integrate sensors into auto alarm system
• Transfer alarm to IP network via email and SNMP trap
Layer 2 Features
• Prevents packet loss with back pressure (half-duplex) and
IEEE 802.3x pause frame ow control (full-duplex)
• High performance of Store-and-Forward architecture, and
runt/CRC ltering eliminates erroneous packets to optimize
the network bandwidth
• Storm Control support
– Broadcast/Multicast/Unicast
• Supports VLAN
– IEEE 802.1Q tagged VLAN
– Supports provider Bridging (VLAN Q-in-Q, IEEE 802.1ad)
– Private VLAN Edge (PVE)
– Port Isolation
– MAC-based VLAN
– Protocol-based VLAN
– Voice VLAN
– GVRP
• Supports SpanningTreeProtocol
– IEEE 802.1D Spanning Tree Protocol (STP)
– IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
– IEEE 802.1s Multiple Spanning Tree Protocol (MSTP),
spanning tree by VLAN
– BPDU Guard
• Supports Link Aggregation
– 802.3ad Link Aggregation Control Protocol (LACP)
– Cisco ether-channel (static trunk)
– Maximum 5 trunk groups with 10 ports per trunk group
– Up to 20Gbps bandwidth (duplex mode)
• Provides port mirror (many-to-1)
• Port mirroring to monitor the incoming or outgoing trafc on a
particular port
• Loop protection to avoid broadcast loops
• Supports ERPS (Ethernet Ring Protection Switching)
• Compatible with Cisco Uni-directional link detection (UDLD)
that monitors a link between two switches and blocks the
ports on both ends of the link if the link fails at any point
between the two devices
• Link Layer Discovery Protocol (LLDP) and LLDP-MED
• Provides ONVIF for co-operating with PLANET video IP
surveillances
Layer 3 IP Routing Features
• Supports maximum 32 static routes and route summarization
Industrial PoE Switch
PoE IP Camera
IP Surveillance Wireless AP
NVR
Dual Band Wireless AP
IGS-10020HPT
PoE PoE PoE
PoE
PoE
100BASE-TX UTP with PoE
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
E24
The IGS-10020HPT also protects customer’s industrial network connectivity with
switching recovery capability that is used for implementing fault tolerant ring and mesh
network architectures. If the Industrial network was interrupted accidentally, the fault
recovery times could be lessthan50ms to quickly bring the network back to normal
operation.
In-vehicle and ITS Industrial Ethernet PoE Solution
The IGS-10020HPT is compliant with e-Mark requirements, making it suitable for a
variety of in-vehicle applications and surveillance systems. To facilitate the 802.3at
PoE+ usage with commonly used 12~48V DC power input for transportation and
industrial-level applications, the IGS-10020HPT adopts 12~48V DC to 52V power boost
technology to solve power source issue but does not require special power supplies. It
fullls the needs of surveillance systems, video transmissions and wireless services on
the bus, shuttles and other vehicles for power and data transmissions.
PoE Switch
PoE Switch
PoE Switch
ERPS Ring for Video Transmission Redundancy
10GBASE-SR/LR Fiber Optic
PoE
1000BASE-T UTP with PoE
Network Video
Recorder
Traffic Control Center
10G
10G
Recovery time <10ms
1000
1000
1000
Outdoor
PoE IP Camera
PoE
PoE
PoE
PoE
PoE
PoE
Outdoor
PoE IP Camera
Outdoor
PoE IP Camera
1000BASE-SX/LX Fiber Optic
1000