0/100BASE-TX to 100BASE-FX Industrial Media Converter IFT-802T / IFT-802TS15 / IFT-805AT User's Manual
Trademarks Copyright © PLANET Technology Corp. 2015. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Table Of Contents 1. Introduction...................................................................... 5 1.1 Package Contents........................................................ 5 1.2 How to Use This Manual.............................................. 5 1.3 Product Features......................................................... 6 1.4 Product Specifications.................................................. 7 2. Installation .................................................................... 10 2.
1. Introduction 1.1 Package Contents Check your package for the following parts: ● 10/100BASE-TX to 100BASE-FX Industrial Media Converter x 1 ● User’s Manual x 1 ● DIN Rail Kit x 1 ● Wall Mount Kit x 1 ● Screws x 1 (set) If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair. 1.
1.3 Product Features Physical Port IFT-802T • 1-Port 10/100BASE-TX RJ45 • 1-Port 100BASE-FX interface for up to 2km (Multi-mode fiber 62.
• Store-and-Forward switching architecture • Features Store-and-Forward mode with wire-speed filtering and forwarding rates • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x pause frame flow control (full-duplex) • Supports packet size of up to 1522bytes • CSMA/CD protocol • Automatic source address learning and aging 1.
Weight 430g Installation DIN rail kit and wall-mount ear Maximum Frame Packet size of 1522bytes Size Flow Control Back pressure for half duplex, IEEE 802.
Speed Twisted-pair: • 10/20Mbps for half / full-duplex • 100/200Mbps for half / full duplex Fiber-optic: • 200Mbps for full-duplex 10/100BASE-TX: • 2-pair UTP Cat. 3, 4, 5 (100 meters, max.) • EIA/TIA-568 100-ohm STP (100 meters, max.) Network Cables 100BASE-FX: • IFT-802T: Multi-mode optic fiber 62.
2. Installation This section describes the functionalities of the Industrial Media Converter’s components and guides you how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. In the following section, the term “Industrial Converter” means the IFT-802T / 802TS15 / 805AT. Media 2.
reliable and flexible to extend the distance from 2km to 60km, depending on the MFB family Fast Ethernet SFP modules. MFB family Fast Ethernet SFP module comes with one of the following models.
2.1.1 Media Converter Front Panel Figure 2-1 & 2-2 & 2-3 show a front panel of Industrial Media Converter. P1 P1 P2 FAULT P2 FAULT P1 TX TX 100 100 RX LNK/ACT P2 FAULT 100 RX LNK/ACT LNK/ACT 100Base-FX 100BASE-FX 100Base-FX 100 100 100 LNK/ACT LNK/ACT LNK/ACT 10/100BASE-TX 10/100Base-TX 10/100Base-TX IFT-802T IFT-802TS15 IFT-805AT Figure 2-1 IFT802T Front Panel Figure 2-2 IFT802TS15 Front Panel Figure 2-3 IFT805AT Front Panel 2.1.
10/100BASE-TX RJ45 Port LED 10/100 Color Green Function Lit: Indicates TP port is successfully connecting to the network at 100Mbps. Off: Indicates TP port is successfully connecting to the network at 10Mbps. Lit: Indicates the link through that port is successfully established. LNK/ACT Green Blinking: Indicates TP port is actively sending or receiving data over that port.
2.1.3 Media Converter Upper Panel The upper panel of the Industrial Media Converter consists one terminal block connector within two DC power inputs. Figure 2-4 shows the upper panel of the Industrial Media Converter. Figure 2-4 Industrial Media Converter Upper Panel. 2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Media Converter is used for two DC redundant inputs. Please follow the steps below to insert the power wire. 1.
2. Tighten the wire-clamp screws for preventing the wires from loosening 1 - Note Power 1 2 + 3 Fault 4 5 - Power 2 6 + The wire gauge for the terminal block should be in the range of 12 to 24 AWG. 2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below.
Note 1. The wire gauge for the terminal block should be in the range of 12 to 24 AWG. 2. Alarm relay circuit accepts up to 30V, max. 3A currents. 2.2 Mounting Installation This section describes how to install the Industrial Media Converter and make connections to it. Please read the following steps to perform the procedures in the order being presented. Note 16 In the installation steps below, this Manual uses the IGS-801 (PLANET 8-port Industrial Gigabit Switch) as an example.
2.2.1 Installing DIN-Rail Mounting Follow the steps below for the DIN-rail mounting of the Industrial Media Converter: Step 1: Screw the DIN-rail on the Industrial Media Converter. 1 2 Step 2: Lightly slide the DIN-rail into the track.
Step 3: Make sure the DIN-rail is tightly on the track. 1 2 Step 4: 18 To remove Industrial Media Converter from the track, lightly lift it up.
2.2.2 Wall-mount Plate Mounting To install the Industrial Media Converter on the wall, please follow the instructions described below: Step 1: Remove the DIN-rail from the Industrial Media Converter; loosen the screws to remove the DIN-rail. Step 2: Place the wall-mount plate on the rear panel of the Industrial Media Converter. Step 3: Use the screws to screw the wall-mount plate on the Industrial Media Converter.
3. Applications In this section, how to install Industrial Media Converter and its installation points are described below: 3.1 Installation Steps Step 1: Unpack the Industrial Media Converter. Step 2: Screw DIN-rail on the Industrial Media Converter. Please refer to the DIN-rail Mounting section for DIN-rail installation if the DIN-rail is not screwed on the Industrial Media Converter.
Step 3: To hang the Industrial Media Converter on the DIN-rail track or wall, please refer to the Mounting Installation section. Step 4: Power on the Industrial Media Converter. Please refer to the Wiring the Power Inputs section for power input. The power LED on the Industrial Media Converter will light up. Please refer to the LED Indicators section for the meaning of LED lights. Step 5: Prepare the twisted-pair, straight-through Category 5 cable for Ethernet connection.
4. Media Converter Operation 4.1 Learning When one packet comes in from any port, the Industrial Media Converter will record the source address, port number and the other related information in the address table. This information will be used to decide whether forwarding or filtering is for future packets. 4.2 Forwarding & Filtering When one packet comes from a port of the Industrial Media Converter, it will also check the destination address besides the source address learning.
The Industrial Media Converter scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the media converter attractive for connecting servers directly to the network, thereby increasing throughput and availability. However, the media converter is the most commonly used to segment the existing hubs, which nearly always improve the overall performance.
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Media Converter is not functioning properly, make sure the Industrial Media Converter was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Media Converter. Performance is bad Solution: Check the speed duplex mode of the partner device.
Why the Industrial Media Converter doesn’t connect to the network Solution: Check per port another port on cable is installed type to turn off again. LED on the Industrial Media Converter. Try the Industrial Media Converter Make sure the properly. And make sure the cable is the right the power. After a while, turn on the power When I connect IFT-80xT to device with 100BASE-FX interface, the 100BASE-FX fiber connection fails Solution: 1. Please check the fiber connection between the two devices is correct.
Appendix A: Networking Connection A.1 Media Converter’s RJ45 Pin Assignments 10/100Mbps, 10/100BASE-TX RJ45 Connector Pin Assignment Contact MDI Media Dependent Interface MDI-X Media Dependent Interface-Cross 1 Tx + (transmit) Rx + (receive) 2 Tx - (transmit) Rx - (receive) 3 Rx + (receive) Tx + (transmit) 4, 5 6 7, 8 Not used Rx - (receive) Tx - (transmit) Not used A.
Straight Cable 1 2 3 4 5 6 7 8 SIDE 1 1 2 3 4 5 6 7 8 SIDE 2 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown SIDE 1 SIDE 2 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown SIDE 1 1 = White/Orange 2 = Orange 3 = White/Green 4 = Blue 5 = White/Blue 6 = Green 7 = White/Brown 8 = Brown SIDE 2 1 = White/Green 2 = Green 3 = White/Orange 4 = Blue 5 = White/Blue 6 = Orange 7 = White/Brown 8 = Brown
EC Declaration of Conformity For the following equipment: *Type of Product: *Model Number: 10/100BASE-TX to 100BASE-FX Industrial Media Converter with Wide Operating Temperature IFT-802T / IFT-802TS15 / IFT-805AT * Produced by: Manufacturer‘s Name : Manufacturer‘s Address: Planet Technology Corp. 11F, No 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C.
