User's Manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial 8-Port 10/100TX +
2-Port Gigabit TP/SFP Combo Ethernet Switch, IFGS-1022TF. In the
following sections, the term “Industrial Ethernet Switch” means
the IFGS-1022TF.
Open the box of the Industrial Ethernet Switch and carefully
unpack it. The box should contain the following items:
Industrial Ethernet
Switch x 1
User’s Manual x 1 Wall-mount Kit x 1
RJ45 Dust Cap x 10 SFP Dust Cap x 2 DIN-rail Kit
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original
packing material, and use them again to repack the product in case
there is a need to return it to us for repair.
Power Requirements Dual 9~48V DC, 24V AC
Power Consumption Max. 7.2 watts/24.6BTU
ESD Protection 6KV DC
Switching Specications
Switch Architecture Store-and-Forward
Switch Fabric 5.6Gbps (non-blocking)
Throughput
(packet per second)
4.16Mpps@ 64 bytes
Address Table
16K entries, automatic source address
learning and aging
Shared Data Buer 4Mbits
Jumbo Frame 10K bytes
Flow Control
IEEE 802.3x pause frame for full-duplex
Back pressure for half-duplex
 Per Gigabit RJ45 Combo Interface (Port-9~Port-10)
109
LED Color Function
LNK/ACT Green
Lights to indicate the link
through that port is successfully
established.
Blinking to indicate that the
switch is actively sending or
receiving data over that port.
O to indicate that the port is
linked down.
1000 Speed Amber
Lights to indicate that the port
is operating at 1000Mbps.
O to indicate that the port is
operating at 10/100Mbps.
 Per SFP Combo Interface (Port-9~Port-10)
IFGS-1022TF
ACTLNK
1000
10
9
10
LED Color Function
1000
LNK/ACT
Green
Lights to indicate that the port
is operating at 1000Mbps.
Blinking to indicate that the
switch is actively sending or
receiving data over that port.
O to indicate that the port is
linked down.
3. Hardware Introduction
3.1 Switch Front Panel
The front panel of the Industrial Ethernet Switch consists of Ethernet
interfaces and LED indicators.
 Front View
P1
LNK/ACT
1 2
3 4
5 6
7 8
P2 Alarm
IFGS-1022TF
ACTLNK
1000
2
6
1
43
5
87
109
10
9
10
Figure 1: IFGS-1022TF Front View
2.ProductSpecications
Product IFGS-1022TF
Hardware Specications
Fast Ethernet
Copper Ports
8 x 10/100BASE-TX RJ45 auto-MDI/MDI-X
ports
Gigabit Ethernet
Copper Ports
2 x 10/100/1000BASE-T RJ45 auto-MDI/
MDI-X ports
(shared with Port-9 and Port-10)
SFP Ports
2 x 1000BASE-SX/LX/BX SFP interfaces
(shared with Port-9 and Port-10)
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
Connector
Removable 6-pin terminal block for power
input
Pin 1/2 for Power 1, Pin 3/4 for fault alarm,
Pin 5/6 for Power 2
Alarm
One relay output for power failure. Alarm
relay current carry ability: 1A @ 24V DC
Dimensions
(W x D x H)
50 x 87.8 x 135 mm
Weight 536g
Standards Conformance
Regulatory
Compliance
FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x ow control and back pressure
IEEE 802.1p Class of Service
IEEE 802.3az Energy Ecient Ethernet (EEE)
Environment
Operating
Temperature
-40 ~ 75 degrees C
Storage
Temperature
-40 ~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)
3.2 LEDDenition:
 System
LED Color Function
P1 Green Lights to indicate power input 1 has power.
P2 Green Lights to indicate power input 2 has power.
Alarm Red
Lights: indicates either power 1 or power 2 has
no power.
 Per 10/100BASE-TX Port
LED Color Function
LNK/
ACT
Green
Lights to indicate that the port is operating at
10/100Mbps.
Blinking to indicate that the switch is actively
sending or receiving data over that port.
O to indicate that the port is linked down.
3.3 Switch Upper Panel
The upper panel of the Industrial Ethernet Switch consists of one
terminal block connector within two power input and one relay
output.
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V , 0.8A max.
AC Input: 24V , 0.4A max.
PWR1
PWR2
Alarm
1 2 3 4 5 6
Figure 2: IFGS-1022TF Top View
3.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Ethernet Switch is used for two redundant power inputs.
Please follow the steps below to insert the power wire.
When performing any of the procedures like inserting
the wires or tightening the wire-clamp screws, make
sure the power is OFF to prevent from getting an
electric shock.