Industrial 8-Port 10/100TX 802.
Table of Contents 1. Package Contents......................................................................................... 3 2. Hardware Introduction.................................................................................. 4 2.1 Physical Dimensions............................................................................... 4 2.2 Switch Front Panel................................................................................. 5 2.3 LED Indicators............................................
1. Package Contents Thank you for purchasing PLANET industrial 8-Port 10/100TX 802.3at PoE+ plus 2-Port Gigabit TP/SFP combo Ethernet Switch, IFGS-1022HPT. In the following sections, the term “Industrial PoE+ Switch” means the IFGS-1022HPT. Open the box of the Industrial PoE+ Switch and carefully unpack it.
1 2 3 4 5 6 7 8 ON Standard 130 [5.12] 4 2 3 1 66 [2.60] ACT ACT PoE-in-Use LNK LNK 1000 IFGS-1022HPT 6 5 802.3at PoE+ 8 7 10 Fault 9 P2 10 P1 9 Long Reach Mode 44 [1.73] DIP Extended Front View Fault PWR2 Bottom View 107 [4.21] Side View PWR1 Max. fault loading: 24V, 1A 30 [1.18] Top View DC Input: 48-56V , 5.5A max. Rear View Mounting Kit DIN-Rail Kit Mounting Kit 18 [0.71] 130 [5.12] 18 [0.71] Side View 36.55 [1.44] 2. Hardware Introduction 2.
2.2 Switch Front Panel The front panel of the Industrial PoE+ Switch consists of 8 10/100/BASE-TX ports featuring 30-watt 802.3at PoE+, and 2 additional Gigabit copper/SFP combo interfaces for Gigabit Ethernet extension and video uplink. The LED indicators are also located on the front panel of the Industrial PoE+ Switch. Figure 2-1 shows the front panel of Industrial PoE+ Switch.
DIP Switch The Industrial PoE+ Switch has a built-in solid DIP switch that provides “Standard” and “Extend” operation modes. The Industrial PoE+ Switch operates as a normal IEEE 802.af/at PoE+ Switch in the “Standard” operation mode. In the “Extend” operation mode, the Industrial PoE+ Switch operates on a perport basis at 10Mbps full duplex operation but can support 30-watt PoE power output over a distance of up to 250 meters overcoming the 100m limit on Ethernet UTP cable.
2.3 LED Indicators System LED Color P1 Green Lit: Indicates power 1 has power. Function P2 Green Lit: Indicates power 2 has power. FAULT Red Lit: Indicates neither power 1 nor power 2 has power. Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 8) LED LNK/ ACT PoE In-Use Color Green Function Lit: Indicates the link through that port is successfully established at 10Mbps or 100Mbps. Blinking: Indicates that the switch is actively sending or receiving data over that port.
2.4 Switch Upper Panel The upper panel of the Industrial PoE+ Switch consists of one terminal block connector within two DC power inputs. Figure 2-2 shows the upper panel of the Industrial PoE+ Switch. Max. fault loading: 24V, 1A 1 2 3 4 5 6 PWR1 Fault PWR2 DC Input: 48-56V , 5.5A max. Figure 2-2: Industrial PoE+ Switch Upper Panel 2.5 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial PoE+ Switch is used for two DC redundant power inputs.
2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 Power 1 + - 3 4 Fault 5 6 Power 2 + - 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2. The DC power input range is 48V ~ 56V DC. Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground Max. fault loading: 24V, 1A 1 2 3 4 5 6 PWR1 Fault PWR2 DC Input: 48-56V , 5.5A max. 2.
the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts. 1 2 Fault Alarm Contacts 3 4 5 Fault 6 The Fault Alarm Contacts are energized (CLOSE) for normal operation and will OPEN when failure occurs Insert the wires into the fault alarm contacts 1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 2.
Industrial Case and Installation IP30 metal case DIN-rail and wall-mount designs 48~56V DC, redundant power with reverse polarity protection Supports 6000V DC Ethernet ESD protection -40 to 75 degrees C operating temperature Switching Hardware-based 10/100Mbps (half/full duplex), 1000Mbps (full duplex), autonegotiation and auto MDI/MDI-X Features Store-and-Forward mode with wire-speed filtering and forwarding rates IEEE 802.
Switch Throughput@64 bytes 4.1Mpps @64 bytes MAC Address Table 16K entries Shared Data Buffer 4Mb SRAM Flow Control IEEE 802.3x pause frame for full duplex.
Dimensions (W x D x H) 66 x 107 x 152mm Weight 916g ESD Protection 6KV DC Enclosure IP30 aluminum case Installation DIN-rail kit and wall-mount kit Power over Ethernet PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE PoE Power Supply Type End-span Power Pin Assignment 1/2(+), 3/6(-) PoE Power Output IEEE 802.3af Standard - Per port 48V~51V DC (depending on the power supply), max. 15.4 watts IEEE 802.3at Standard - Per port 51V~56V DC (depending on the power supply), max.
3. Installation This section describes the functionalities of the Industrial PoE+ Switch’s components and guides you to installing it on the DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. Note This following picture shows the user how to install the device, and the device is not IFGS-1022HPT. 3.1 DIN-rail Mounting Installation The DIN-rail bracket is screwed on the Industrial PoE+ Switch when out of factory.
Step 2: Lightly insert the bottom of the switch into the track. 1 2 Step 3: Make sure the DIN-rail bracket is tightly secured on the track. Step 4: Please refer to the following procedure to remove the Industrial PoE+ Switch from the track. 1 2 Step 5: Lightly pull out the bottom of the switch for removing it from the track.
3.2 Wall-mount Plate Mounting To install the Industrial PoE+ Switch on the wall, please follow the instructions described below. Step 1: To remove the DIN-rail bracket from the Industrial PoE+ Switch, loosen the screws to remove the DIN-rail bracket. Step 2: Place the wall-mount plate on the rear panel of the Industrial PoE+ Switch. Step 3: Use the screws to screw the wall-mount plate on the Industrial PoE+ Switch.
3.3 Installing the SFP Transceiver The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and hot-swappable. You can plug in and out the transceiver to/from any SFP port without having to power down the Industrial PoE+ Switch as 3-1 shows. MGB Series Transceiver Figure 3-1: Plugging in the SFP Transceiver PLANET Industrial PoE+ Switch supports 1000Mbps mode with both single mode and multi-mode SFP transceivers. 1.
Note It is recommended to use PLANET SFPs on the Industrial PoE+ Switch. If you insert an SFP transceiver that is not supported, the Industrial PoE+ Switch will not recognize it. 3.4 Removing the Transceiver Module 1. Make sure there is no network activity by consulting or checking with the network administrator. Or through the management interface of the switch/ converter (if available) to disable the port in advance. 2. Remove the Fiber Optic Cable gently. 3.
4. Troubleshooting This chapter contains information to help you solve issues. If the Industrial PoE+ Switch is not functioning properly, make sure the Industrial PoE+ Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial PoE+ Switch. Per port LED is lit, but the traffic is irregular Solution: Check whether the attached device is not set to dedicated full duplex.
APPENDIX A: Networking Connection A.1 PoE RJ45 Port Pin Assignments (End-span) PIN NO RJ45 POWER ASSIGNMENT 1 Power + 2 Power + 3 Power - 6 Power - 12345678 A.
A.3 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded.
A.4 Fiber Optic Cable Connection Parameter The wiring details are shown below: 1000X Fiber Optic Cables: Standard Fiber Type Cable Specifications 1000BASE-SX (850nm) Multi-mode 50/125μm or 62.5/125μm Multi-mode 50/125μm or 62.5/125μm Single-mode 9/125μm 1000BASE-LX (1300nm) Wiring Distances: Standard 1000BASE-SX 1000BASE-LX 22 Fiber Diameter (micron) Modal Bandwidth (MHz * km) Max. Distance (meters) MM 62.5 62.5 50 50 100 200 400 500 220 275 500 550 MM 62.
APPENDIX B: Approved PLANET SFP Transceivers The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules MGB-GT SFP-Port 1000 BASE-T Module MGB-LX SFP-Port 1000 BASE-LX mini-GBIC module - 20km MGB-SX SFP-Port 1000 BASE-SX mini-GBIC module - 550m MGB-SX2 SFP-Port 1000 BASE-SX mini-GBIC module - 2km MGB-L40 SFP-Port 1000 BASE-LX mini-GBIC module - 40km MGB-L80 SFP-Port 1000 BASE-LX mini-GBIC module - 80km MGB-L120 SFP-Port 1000 BAS
MGB-TL80 SFP-Port 1000 BASE-LX mini-GBIC module - 80km (-40~75°C) MGB-TSA MGB-TSB SFP-Port 1000 BASE-BX (WDM, TX:1310nm) mini-GBIC module 2km (-40~75°C) SFP-Port 1000 BASE-BX (WDM, TX:1550nm) mini-GBIC module 2km (-40~75°C) MGB-TLA10 MGB-TLB10 SFP-Port 1000 BASE-BX (WDM, TX:1310nm) mini-GBIC module 10km (-40~75°C) SFP-Port 1000 BASE-BX (WDM, TX:1550nm) mini-GBIC module 10km (-40~75°C) MGB-TLA20 MGB-TLB20 SFP-Port 1000 BASE-BX (WDM, TX:1310nm) mini-GBIC module 20km (-40~75°C) SFP-Port 1000 BASE-BX (WD
