IP DSLAM Switch IDL-2402 User's Manual -1-
Copyright Copyright (C) 2008 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted.
Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade names. In most, if not all cases, these designations are claimed as trademarks or registered trademarks by their respective companies.
Table of Contents 1. Introduction ............................................................................................................. 16 1.1 Product Features ............................................................................................. 16 1.2 Package Contents............................................................................................ 17 1.3 Application ....................................................................................................... 18 1.
4.3.2 VLAN Configuration ............................................................................... 92 4.3.3 Access Control ..................................................................................... 100 4.3.4 Forwarding ........................................................................................... 127 4.3.5 Relay.................................................................................................... 129 4.3.6 IGMP......................................................
5.3.4 show access-list dstip .......................................................................... 216 5.3.5 show access-list dstmac ...................................................................... 217 5.3.6 show access-list ethertype................................................................... 217 5.3.7 show access-list ip-allowed.................................................................. 217 5.3.8 show access-list ipprotocol .........................................................
5.3.52 show interface xdsl {all | } adsl channel ................................... 229 5.3.53 show interface xdsl {all | } adsl failure ...................................... 229 5.3.54 show interface xdsl {all | } adsl line .......................................... 230 5.3.55 show interface xdsl {all | } adsl line config................................ 230 5.3.56 show interface xdsl {all | } adsl line delt-test ............................ 230 5.3.
5.3.100 show rmon statistic .......................................................................... 242 5.3.101 show route ....................................................................................... 242 5.3.102 show runningcfg............................................................................... 242 5.3.103 show runningcfg interface gigabit..................................................... 242 5.3.104 show runningcfg interface xdsl..................................................
5.4.25 dsl-line-identify dhcp option82 sub..................................................... 252 5.4.26 dsl-line-identify dhcp option82 remote ............................................... 252 5.4.27 dsl-line-identify pppoe srv-name ........................................................ 253 5.4.28 dsl-line-identify pppoe srv-name-check.............................................. 253 5.4.29 fdbstatic {xdsl | gigabit} ..................................................... 253 5.4.
5.4.73 remotecfg login .................................................................................. 265 5.4.74 restore-factory.................................................................................... 265 5.4.75 rmon alarm alarm_interval.................................................... 265 5.4.76 rmon alarm delete ................................................................ 266 5.4.77 rmon alarm falling_eventindex .............................................
5.4.121 temperature shelf time ..................................................................... 281 5.4.122 time set date .................................................................................... 282 5.4.123 time set time..................................................................................... 282 5.4.124 time set timezone............................................................................. 283 5.4.125 vlan ethertype s-tag .................................................
5.7.30 pvc atmdesc....................................................................................... 297 5.7.31 pvc atmdesc plc ................................................................................. 297 5.7.32 pvc atmdesc shp ................................................................................ 298 5.7.33 pvc encapsulation .............................................................................. 298 5.7.34 quiet-period .........................................................
5.10.1 line mode carrier ................................................................................ 310 5.10.2 line mode diagnostic .......................................................................... 310 5.10.3 line mode force-l3 .............................................................................. 310 5.10.4 line mode mask.................................................................................. 310 5.10.5 line port .............................................................
5.13.7 vbr2.................................................................................................... 329 5.13.8 vbr3.................................................................................................... 330 5.13.9 ubr-shp............................................................................................... 331 5.13.10 cbr-shp............................................................................................. 331 5.13.11 vbr-shp .....................................
5.19.1 aggregate........................................................................................... 355 5.19.2 bands {start | stop} ............................................................... 355 5.19.3 bands mask.......................................................................... 355 5.19.4 carriermask ........................................................................................ 356 5.19.5 message-based ...........................................................
1. Introduction Planet IDL-2402 is a 24-port ADSL/ADSL2/ADSL2+ mini IP DSLAM, which has one 1000Base-T uplink Interface, for efficient scalability and easy deployment in the network with small ADSL environment. With built-in POTS splitter subscriber ports, the PLANET IDL-2402 is a Cost-Effective Solution for Network Service Provider to offer excellent services to multiple subscribers.
1.
1.3 Application The PLANET IDL-2402 offers the benefit of high performance to central office co-location and MTU (Multi-Tenant Unit) / MDU (Multi-Dwelling Unit) markets. It provides broadband data service over existing copper wires without affecting the conventional voice service by 24 subscriber ports with built-in POTS splitter. A PLANET IP DSLAM is the perfect solution for NSP a cost-effective but high-value centrally management capability.
1.4 Outlook 1.4.1 Front Panel The front panels of IDL-2402 are shown below.
1.5 Technical Specifications Product IP DSLAM Model IDL-2402 Hardware Specification 1.5U high box-type with a rack-mountable enclosure Case 1 x RJ-45 (10/100/1000Base-T) Uplink Console RS-232 Serial Port (9600, 8, N, 1) Ports 1 x RJ-21 Connector LINE 1 x RJ-21 Connector PHONE 1 x SYS LED 1 x ALM LED LED Indicators 1 x Uplink LED 24 x ADSL LEDs Software Specification Compliant with ADSL standard − ANSI T1.413 issue 2 − G.dmt (ITU G.992.1) − G.lite (ITU G.992.2) − G.hs (ITU G.994.
Function − Complies with RFC2684 bridged payload encapsulation mode Up to 256 multicast groups and 512 copies simultaneously − Up to 48 profile-based Multicast Access Control − Limit maximum number of IGMP groups joined per bridge port − IGMP snooping / proxy per IGMP v1, v2, and v3 − IGMP proxy and IGMP snooping Selection − Supports Layer-2 frame filtering based on MAC and Ether Type − Supports Layer-3 filtering based on IP, Protocol, and Port number − IEEE 802.
2. Installation The followings are instructions for setting up the IDL-2402. Refer to the illustration and follow the simple steps below to quickly install your IP DSLAM. 2.1 Safety Instruction The following is the safety instructions for IP DSLAM before installing. >> The maximum operating temperature of the IP DSLAM is 65ºC.
2.2 Hardware Installation The PLANET IDL-2402 is a 1.5U high box-type IP DSLAM with rack-mountable enclosure. It can be installed in a standard 19-inch rack by using the mounting brackets provided. Mount the shelf on the rack using the large screws provided. The procedure to connect and wire the system is as follows. 2.2.1 System Requirements z z z z z z Workstation with Windows NT/2000/XP RJ-45 cables RJ-11 cables Telco-50 cables RS-232 console cable MDF Patch Panel (Model No.: IDL-PAN-48). 2.
Step 2: Connecting the ADSL LINE and PHONE interfaces The IDL-2402 supports 24 ports ADSL subscribers per box. There are two RJ21 50-pin female connectors on the front panel of the system. One for ADSL line and one for POTS interface. To connect the subscriber lines, use cables with the RJ21 50-pin male connectors. When installing, just plug the end of a cable with connector into the LINE and PHONE interface female connector on the front panel.
Front Panel Connection Front panel connection of IDL-2402 UPLINK Port: Connect to Internet by RJ-45 cable. Console Port: Connect to PC by RS-232 console cable in order to administer your IP DSLAM through CLI.The Console interface on the front panel is the main control interface of the IDL-2402.
To connect the host PC to the console port, a RJ45 (male) connector-to-RS232 DB9 (female) connector cable is required. The RJ45 connector of the cable is connected to the Console port of the DSLAM; the DB9 connector of the cable is connected to the PC COM port. The pin assignment of the console cable is shown below: DB-9F RJ-45M Pin 1 2 Pin 2 RD 3 Pin 3 TD 4 5 Pin 5 DGND 6 7 8 Pin Assignment of Console Cable Step 3: Hook power cord and apply the power.
2.3 WEB Configuration This section describes how to use Web Configuration Tool to maintain your IP DSLAM. The IDL-2402 contains a HTTP server. You can login and configure it by using your Web Browser. 2.3.1 System Prepartion Before attempting to configure the IDL-2402, please ensure as below: Set your computer’s IP with the same network mask of the router. (For example: Router’s default IP is 192.168.1.1 / 255.255.255.0) Then you can set computer’s IP to: 192.168.1.x / 255.255.255.0.
Step 2 : Login the IDL-2402 A login page will appear. Please type your username / password and click “Sign in”. (The default username / password is admin / admin) After you login the IDL-2402, you will see the system information as below.
Step 3 : Configure the DSL PVC Go to “Bridge Æ Interface Setup Æ ADSL PVC” setting screen, select the ADSL port and click “Create” to apply the PVC settings. For example, create PVC-1 to Port 1. The default VPI / VCI is 0 / 35.
Step 4 : Enable the ADSL Port Service Go to “System Æ ADSL Port Service” setting screen, select the ADSL port and Admin is “ON”. Click “Modify” to make this Port is ON. You can see the Admin status became to ON.
Step 5 : Connect the ADSL2/2+ CPE to Patch Panel Connect the ADSL2/2+ CPE to Patch Panel and configure it, the VPI / VCI value must be the same with IDL-2402. After finish setting, the CPE will establish the ADSL connection with IDL-2402. You can check the connection status as below figure. The Current Status is ON. Now the clients can access to Internet through IDL-2402.
2.3.3 How to backup / Restore the Configuration Configuration Import / Export The IDL-2402 provides the configuration preservation feature that the configuration database is stored in flash memory (two partitions available). In addition to the configuration preservation feature, the IDL-2402 also provides the configuration export/import feature. DB Configuration Concept For CLI: Suppose that TFTP Server IP address is 172.16.100.
(B) Import file from TFTP Server to the Download Config and then load Download Config to the Running Config. Ex: enable configure remotecfg login 172.16.100.181 get testcfg load (C) Export: export file from Running config to the TFTP server. Ex: enable configure runningcfg login 172.16.100.181 put testcfg (D) Save Running config to the Flash (partition 1 or partition 2).
For Web: On the menu tree, click on Maintenance --- > Database. The Database Configuration page is displayed. Select the database configuration action you want to perform. (A) Import File (Write Download Config To Flash): Type in the TFTP Server IP address and the name of the file you want to download. Then click on Get File button.
Write to memory successfully: Fail to Get File: - 35 -
(B) Import File (Load Remote Config to Running Config) Type in the TFTP Server IP address and the name of the file you want to download. Then click on Get File button.
(C) Export File (Put Running Config to Remote TFTP Server) Type in the TFTP Server IP address and the name of the file you want to export. Then click on Put File button.
(D) Save Running Config to Flash (System Config) Click on the drop-down list and select partition, and then click on Write_Running button to write running configuration to Flash.
(E) Reload Flash to Running Config Click on the drop-down list and select partition, and then click on LOAD_FLASH button to load configuration from Flash to Running Config.
(F) Restore Factory Default Click on Factory_Default button to restore factory default configuration. After loading default configuration to Flash successfully, you must click on RESTART button to restart the system so that the configuration can take effect.
(G) Flash Boot Point Configuration Select Click on the Boot Config drop-down list and select the partition (Partition1 or Partition2) as the boot point. Click on Apply button and then restart the system. The system will restart and load the configuration in the partition you select into the running configuration.
2.3.4 Firmware Update For CLI: If you want to update firmware code, you must get image file from FTP Server. Suppose that FTP Server IP address is 172.16.10.219 and the image filename is ‘vmlinux_u2402_ 1.00B05’. Example: 1. Firmware update: enable //go to enable mode configure //go to configuration mode firmware login 172.16.10.219 username share password tg123 firmware upgrade vmlinux_u2402_1.00B05 (Firmware upgrade may take a few minutes, don’t turn off or reset the system during the process.
For Web: On the menu tree, click on Maintenance --- > Firmware Update. The Firmware Update page is displayed. Once you have entered all the necessary values, click on Firmware Update button to start updating the firmware. Label Firmware Update Description Once you have typed in the parameter values, click on this button to start firmware update. Remote FTP Server IP Type in the IP address of the FTP server. Server User Name Type in the ftp user name. Server Password Type in the ftp password.
This section displays the partition information including firmware version, updating date, and status (active or not). Note that active partition means the partition for next power-up, not current partition in use. You can refer Partition Information to Current Version to know which partition is the current partition in use. When you update the firmware, new firmware will be written to the partition that is not currently in use.
3. Software Introduction 3.1 General Overview The software architecture of the IDL-2402 is shown in the figure below. It can be divided into three layers: the management layer, the OAM&P layer, and the firmware layer.
3.1.
3.2 Configuration Management The configuration management contains the following aspects: 1.
4. 3.2.2 ADSL Configuration” below for more description) 5. ATM traffic management 6. SNMP setup The configuration management provides detecting and reporting to the operators through SNMP Trap for all memory updates reflecting changes in the system configuration. It also provides logging the changes in the operational state and making this information available (on-demand) to the operators over the operation interface.
3.2.2 ADSL Configuration Configuration for an ADSLx user port is provisioned by the parameter set, which is a group of attributes that determine the user port behaviors; and we call it as a profile. The IDL-2402 provides a profile-based provisioning per the definition of ITUT G997.1 and RFC 2662 for ADSL line configuration data and a mechanism to associate the ADSL port to these profiles. One or more ADSL lines may be configured to share parameters of a single profile.
3.3 Performance management Performance management supports performance monitoring by collecting and thresholding performance parameter counters against 15-miniute intervals for each interface and module respectively. Users can query the data of these parameters through CLI and Web-GUI. Performance statistics include the following: 1. Statistics for current interval: A real-time aspect contains the reflection of the current value situation before the new interval.
ATUC_CU User Total Cell Count ATUC_CD Delineated Total Cell Count ATUC_HEC ATM Header Error Count ATUC_IBE ATUC_CVS Idle Cell Bit Error Count The counter associated with the number of Coding Violations encountered by the channel. The counter associated with the number of corrected codewords encountered by the channel.
3.3.1 RMON Feature The IDL-2402 supports performance statistics defined in RMON MIB groups 1 (Ethernet statistics), 2 (history control), 3 (Ethernet history), 4 (alarm), 5 (event), and 6 (log) per RFC 2819 for all network uplink 10/100/1000 ports.
HistoryUndersizePkts Monitoring rx undersize packets HistoryOversizePkts Monitoring rx oversize packets HistoryFragments Monitoring rx fragments packets HistoryJabbers Monitoring rx jabber packets HistoryCollisions Monitoring tx single collision packets HistoryTxBytes Monitoring tx bytes HistoryTxPackets Monitoring tx packets HistoryTxMulticast Monitoring tx multicast HistoryTxBroadcast Monitoring tx broadcast HistoryUtilization Monitoring tx Utilization - 53 -
3.4 Fault Management Fault management is conceptually partitioned into two levels: the system top level, and interface-specific level. Both levels are alarm-level configurable and can be Major and Minor. All the alarms are mask-able. Fault management provides the alarm output through hardware output interface (on the system front panel) and visible indicator (LED). The alarm/status indications are automatically generated as a result of certain events/conditions.
ADSL Alarms The IDL-2402 provides the following ADSL alarms: LOS (Loss of Signal) -Near End/Far End LOF (Loss of Frame) -Near End/Far End LOM (Loss of Margin) -Near End/Far End LCD (Loss of Cell Delineation) -Near End/Far End NCD (No Cell Delineation) -Near End/Far End LOPWR (Loss of Power) -Far End COMMF: Unable to communicate with peer modem -Far End NOPEER: No peer present – Far End - 55 -
3.5 Loopback Testing The IDL-2402 supports ATM and ADSL loop diagnostics. ATM: The system provides F5 end-to-end or segment loopback. ADSL: The system provides Dual Ended Loop Testing (DELT) for each ADSL line on a per port basis, according to the definition per section 8.12.3 of ITUT G992.3.
3.6 Cluster Feature The IDL-2402 supports Cluster feature that can make a group of NEs (network elements) work together as a single NE from the management point of view. Operators can manage the NEs in a cluster, called cluster nodes, via the same single IP address in terms of CLI, Web-based GUI or SNMP based management interfaces. The IDL-2402 currently provides cluster feature that a cluster can include up to four cluster members (NEs).
4. WEB Management Web Configuration Tool Overview To access Web Configuration Tool on an IDL-2402: 1. Connect a PC to the console port of the DSLAM. At the console, type the following CLI command: WDS:>enable /*enter the enable command mode from initial mode*/ WDS:%show management all /*display all in-band management IP setting*/ The default LAN IP address is got via DHCP. 2. At your web browser, enter the URL you retrieve by using the above command.
4. The following page is displayed. This is the homepage of the Web Configuration Tool.
About Web Configuration Tool Pages The Web Configuration Tool provides a series of web pages for users to setup and configure the IDL-2402 System. These pages are organized into six main topics including System, Bridge, ADSL, Traffic, SNMP, and Maintenance. You can select each topic from the menu on the left-hand side of the main window. Table 4-1 lists the various pages of the web configuration tool.
Relay DSL Line Identify Protocol & Route Port IGMP IGMP Profile IGMP Multicast BRAS MAC IPOA Interface Setup ADSL Service Profile (main) Service Profile (Channel) Profile Spectrum Profile (main) Spectrum Profile (ADSLx) TCA Profile Inventory Data & Inventory Loop Test Carrier Data OP Data Line Config & Info Traffic ATM Traffic Descriptor SNMP SNMP Community Line Configuration Line Information SNMP Target SNMP Notify Maintenance SYS Log Server Database Firmware Update ATM Loopbacks Alarm/Eve
4.1 System 4.1.1 System Information The System Information page (the default page you’ll see after you login the web configuration tool) contains information about the user access level, current system date and time, current boot configuration partition, system MAC address, system HW/SW/FW version, web configuration software version, supported subscriber line type (AnnexA or AnnexB), GBE interface status, and LED status (SYS and ALM). From the System menu, click on System Info.
4.1.2 Board IP Setup This option allows you to configure the in band IP address setting, VID management setting, HTTP port setting, etc. From the System menu, click on Board IP Setup. The following page is displayed: Board IP Setup Table Label In Band Address Description IP Address Type in the IP address of the DSLAM for in-band management. Subnet Mask Type in the in-band subnet mask of the DSLAM.
4.1.3 Ethernet Port Service This option allows you to set the administration state and select the speed mode for the Gigabit Ethernet ports. From the System menu, click on Ethernet Port Service. The following page is displayed: Ethernet Port Service Setup Description Label Port This field shows port number of the Gigabit Ethernet interface. Admin Status Click on the drop-down list and select the administrative state (ON/OFF) to enable/disable the GBE port.
4.1.4 ADSL Port Service This option allows you to setup the service status of the line ports and to bind the selected service profiles and spectrum profiles. Also, you can query current setting and the operational status of the line ports. From the System menu, click on ADSL Port Service. The following page is displayed: First click on the drop-down list to select the port range to be displayed.
TCA Profile Type in the index of the TCA Profile (1~64). All Select the check box to select all circuits of current page. Modify Click on this button to submit the modification. Query Click on this button to get most recent status of the circuits. Select Click on the radio button to select the port to be modified. Current Status This field shows the operational status of the line ports. Possible values are ON (enabled), OFF (disabled), and Testing (in loop testing now).
4.1.5 CLI Setup This option allows you to modify the timeout setting for a CLI session and the allowable number of CLI sessions. From the System menu, click on CLI Setup. CLI Setup Label Description CLI Session Allowable number of CLI sessions at the same time. Valid value: 1~10. CLI Timeout CLI session will be closed once the idle time exceeds this timeout value. Valid value: 180~3600 (sec). Default Click on this button to set default values (CLI session: 5, CLI timeout: 300 sec).
4.1.6 Cluster Setup This option allows you to setup Cluster function, which can make a group of NEs (network elements) work together as a single NE from the management point of view. Before you group a Master and a Slave IPDSLAM, some parameters need to be well configured: 1. Cluster domain name: The group name for a cluster must be the same on Master and Slave. 2. Cluster IP address: IP address to be used for remote management when Master and Slave are grouped together. 3.
To make the DSLAM join a cluster, select the Role as “Cluster” or “Slave only” according to your plan and then click on Modify. The state of the Cluster Configuration will show from DISCOVERING to VOTING to MASTER or SLAVE at last. The following figure shows the Cluster Setup page of a cluster containing two cluster members. You will see the following page if you’re connecting directly to the Master via its in-band IP address or connecting to the Cluster IP “172.16.77.88”.
for the DSLAM to be a master in a cluster. But if there’s already a Master in a cluster, a new added DSLAM cannot try to be the Master by entering a smaller voting key number; the Master cannot be changed in this way. IP Type in the cluster IP address. Users can connect to and manage the cluster via the cluster IP address through in-band connection. Netmask Type in the cluster’s subnet mask. Gateway Type in the cluster’s gateway IP address.
4.1.7 System Inventory This option allows you to retrieve the system inventory including Description of the System, HW/FW/SW Version, Model Information, Part Number, Hardware Revision, and Serial Number. From the System menu, click on System Inventory. Click on the Query button.
4.1.8 System Contact Info This option allows you to specify the system name, system contact, and system location. From the System menu, click on System Contact Info. The following page is displayed: Type in the value you desire, and then click on Modify to apply the setting. Click on Query to verify if the value is changed.
4.1.9 SNTP This option allows you to setup the Simple Network Time Protocol (SNTP). From the System menu, click on SNTP. The following page is displayed. SNTP Setup Label Description Time Zone Sets the local time zone by selecting in the Time Zone drop-down list. Sixty-five of the world’s time zones are presented (including those using standard time and summer/daylight savings time). System Date Sets system date (yyyy/mm/dd). System Time Sets system time (hh:mm:ss).
4.1.10 IP Routes This option allows you to configure the IP route table for the in-band management traffic. From the System menu, click on IP Routes. The following page is displayed: Click on the drop-down list to select the page to be displayed first. IP Route Setup Label Description This field shows current system default gateway. You can modify the gateway address by typing in new value and then click on Set.
4.1.11 User Administration This option allows you to administer accounts for users who access the DSLAM. From the System menu, click on User Administration. Click on Select: drop-down list and select a page to display. The following page is displayed: User Administration Label Page Description Click on the drop-down list and select the page to be displayed. Click on this button to create a new user.
User Name Shows the name of the user (up to 32 characters). The available access levels include: Level SUPERUSER, ENGINEER, and GUEST. Aging day Set password expiration days (0 for no expiration days) Start Date Shows the day when the account was first created. Last Login Shows the day when a user last login. Comment Description about the user account (up to 31 characters).
4.1.12 Duplicator This option allows you to duplicate all/partial the configurations of one selected line port (as a template) to other ports (as many as you want). From the System menu, click on Duplicator. The following page is displayed. Select the content of configurations (ADSL line configuration, ADSL profiles, or…) you want to duplicate first. Then specify the port number as the template (the source port to be copied), and select the target ports to which the template is going to be copied.
4.2 802.1x Security 4.2.1 System Protocol This option allows you to enable/disable 802.1x authentication function of the system, and setup the 802.1x authentication mechanism for each line bridge port. Before you setup 802.1x for a line bridge port, you must create the ADSL PVC (bridge port) first. Authenticator Supplicant (line user) (Our system) Authentication Server (RADIUS) From the 802.1x Security menu, click on System Protocol.
System Protocol Setup - Main Setting Label Description System Authentication section Click on the drop-down list to enable or disable the 802.1x authentication function of the system. If you select “Disabled”, any setting in the Port Authentication section will not take effect. Port Authentication section – Main Setting Select the line bridge port range to be listed.
Timer Setting - 80 -
System Protocol Setup – Timer setting Label Description Port Authentication section – Timer Setting Select the line bridge port range to be listed. Select Port Remember to select the checkbox when you want to modify/delete the setting of a bridge port or set a bridge port to its default value. Supplicant Timeout Type in the number of seconds our system will wait for a response before resending the request to the supplicant. Default is 60 (sec).
4.2.2 RADIUS &Local Profile The IDL-2402 system supports RADIUS client function for authenticating line ports with local authentication database or remote RADIUS server. From the 802.1x Security menu, click on RADIUS & Local Profile. The following page is displayed: RADIUS & Local Profile Setup Label Description Authentication Method section In this section, operators setup four AAA methods for the system to use, and the priority order is Method1 > Method2 > Method3 > Method4.
Max Fail Type in the maximum authentication attempts. allowable times of continuously VLAN ID Type in the VID of the VLAN which the RADIUS server belongs to. Secret ID Type in the authentication key in text format. failed Local Profile section Click on the drop-down list and select the profile range to be listed. There are total 8 pages and 8 profiles per page (up to 64 local profiles can be set in our system). Username Type in the username for authentication.
4.3 Bridge 4.3.1 Interface Setup 4.3.1.1 GIGA Bridge This option allows you to setup the GBE (trunk) bridge interface. From the Bridge menu, click on Interface Setup and then GIGA Bridge. The following page is displayed: GIGA (Trunk) Bridge Setup Label Description Mode Click on the drop-down list and specify the trunk port to be an Uplink or User (especially for system stacking). VID Type in the default port VLAN ID. Valid value is 1 ~ 4094.
Isol ON/OFF: to enable/disable isolation. When port isolation is enabled, packets received from a trunk port (when both the trunk interfaces are configured as up-link) cannot be forwarded to the other trunk port even for broadcasting. To modify the configuration of a giga port: 1. Click on the radio button to select trunk port 1 Modify 2. Change the parameter values 3. Click on Modify button to apply new values Query Click on this button to query current status.
4.3.1.2 ADSL PVC This option allows you to setup the ADSL PVC. From the Bridge menu, click on Interface Setup and then ADSL PVC. The following page is displayed: You shall click on the drop-down lists to select port range and PVC first. Then the data of these PVCs (bridge ports) you selected will be displayed. Click on the radio button to select the PVC you want to create, modify, or delete. ADSL PVC Setup Label Description VPI Type in the VPI value: 0 ~ 255. Default value is 0.
Encap Select AAL5 Encapsulation Type: VCMUX, LLC, or AUTO (for PVC#1 ~ PVC#4 only)*. Protocol Based VLAN Select in the drop-down list to enable or disable protocol based VLAN function. When protocol based VLAN is enabled, the bridge port will work according to the protocol based VLAN table (refer to section 4.3.2). All Select the check box to copy specified circuit to all remainder circuits in current page. Create Click on the radio button to select a PVC (bridge port) that has not been created.
4.3.1.3 ADSL Bridge This option allows you to setup the ADSL bridge interface. From the Bridge menu, click on Interface Setup and then ADSL Bridge. The following page is displayed: You shall click on the drop-down lists to select port range and PVC first. Then the data of these PVCs (bridge ports) you selected will be displayed. Click on the radio button to select the bridge port you want to modify. ADSL Bridge Setup Label VID Description Type in the default port VLAN ID. Valid value is 1 ~ 4094.
removed) and a single-tagged packet will leave untagged. Pri-0 ~ 7: set the default VLAN priority level. no Stack/Stack/TLS: disable N:1 VLAN stacking / enable N:1 VLAN stacking (our system adds the default VLAN tag to all the incoming frames through this port) / enable TLS (transparent LAN service) so that this bridge port becomes VLAN transparent (refer to DSL Forum, TR-101). A pre-configured S-Tag is used to encapsulate TLS traffic going through this port.
4.3.1.4 ADSL Port Security This option allows you to setup the ADSL port security. From the Bridge menu, click on Interface Setup and then ADSL Port Security. The following page is displayed: You shall click on the drop-down lists to select port range and PVC first. Then the data of these PVCs (bridge ports) you selected will be displayed. Click on the radio button to select the bridge port you want to modify.
So you need to define the source IP addresses that bind to this bridge port. Then the IP packets that contain these source IP addresses can pass through this bridge port; otherwise the packets will be blocked. All Select the check box to copy specified circuit to all remainder circuits in current page. Modify Click on the radio button to select the bridge port you want to modify. Change the parameter values and then click on Modify. Query Click on this button to get the most recent data.
4.3.2 VLAN Configuration 4.3.2.1 Static VLAN This option allows you to configure the static VLAN table. From the Bridge menu, click on VLAN Configuration and then Static VLAN. The following page is displayed. Click on the radio button to select CONFIG VLAN to configure static VLAN for the bridge ports or SHOW VLAN to display the VLAN table. CONFIG VLAN Click on the drop-down list to select ADSL or GIGA port, and then select a port and PVC if ADSL is selected.
SHOW VLAN In the following page, type in the VID and then click on Query. All the bridge ports belonging to the VLAN and the configuration data of these ports will be displayed in the table.
4.3.2.2 Protocol Base VLAN This option allows you to configure the protocol based VLAN table. From the Bridge menu, click on VLAN Configuration and then Protocol Base VLAN. The following page is displayed. Select the checkboxes of the entries you want to create or delete. To create a new entry, type in the VLAN ID and select the EtherType (protocol). If you select Other for EtherType, type the EtherType value in the rightmost field.
4.3.2.3 Translation VLAN This option allows you to configure the translation VLAN table, which defines some special VLAN working rules such as VLAN stack, VLAN cross-connect, etc. Before you configure the Translation VLAN table for a line bridge port, you shall configure the Static VLAN table for this line bridge port and the GIGA bridge port in advance. Also, you shall disable VLAN stacking feature of this line bridge port in the ADSL bridge interface setup page (refer to section 4.3.
Upstream: C-TagÆ(User port)-----(Uplink port)ÆS-Tag Downstream: S-TagÆ(Uplink port)-----(User port)ÆC-Tag 3. Stacking In this mode, the system will add S-TAG before user port’s C-TAG. Note that the mapping from C-Tag to S-Tag+C-Tag is still one to one. So a user port’s C-Tag can’t be used for another translation rule, as well as an uplink port’s S-Tag+C-Tag. Upstream: C-TagÆ(User port)-------(Uplink port)ÆS-Tag+C-Tag Downstream: S-Tag+C-TagÆ(Uplink port)--------(User port)ÆC-Tag 4.
N:1 VLAN (N:1 User Mode): N:1 can also be called shared VLAN, so in this mode MAC learning function of the bridge ports must not be disabled. 1. Replaced N:1 In this mode, the system will change the user port’s C-Tag to the Uplink port’s S-Tag. And the mapping is N to 1, so a user port’s C-Tag can’t be used for another VLAN translation rule. But an uplink port’s S-Tag can be used for another N:1 VLAN translation rule. So in this mode several bridge ports can have the same VLAN cross-connect rule.
4.3.2.4 Static Allowed IP This option allows you to configure the Static Allowed IP table. From the Bridge menu, click on VLAN Configuration and then Static Allowed IP. The following page is displayed. To make bridge port work according to this Static Allowed IP table, the IP allowed function must be enabled (refer to section 4.3.1). Click on the drop-down lists to select ADSL port and PVC number, then type in VID and allowed source IP that can pass through the VLAN.
4.3.2.5 MAC Spoofing This option allows you to enable/disable anti-MAC Spoofing function and MAC-Spoofing detection log function. From the Bridge menu, click on VLAN Configuration and then MAC Spoofing. The following page is displayed. MAC Spoofing Setup Label Description Click on the drop-down list to select: Spoofing OFF: The system is able to provide service to users with duplicate MAC addresses.
4.3.3 Access Control 4.3.3.1 Filtering This option allows you to setup the filter rule for the packets. From the Bridge menu, click on Access Control and then Filtering. The following page is displayed. Click on Filtering Type drop-down list to select a filtering type first. Protocol Filtering Protocol Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256.
Once you have specified the serial number, click on this button to delete the filter rules in the table. Delete Click on these drop-down lists to select an ADSL bridge port or GIGA bridge port. Protocol Click on this drop-down list and select a protocol to deny: ICMP, IGMP, IP in IP, TCP, GRP, IGP, UDP, GRE, EIGRP, or OSPF. Create Click on this button to create a new filter rule in the table.
IP Address Filtering Source IP Address Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256. Query Once you have specified the serial number, click on this button to display the filter rules. Delete Once you have specified the serial number, click on this button to delete the filter rules in the table.
Layer 4 Destination Port Filtering Layer 4 Destination Port Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256. Query Once you have specified the serial number, click on this button to display the filter rules. Delete Once you have specified the serial number, click on this button to delete the filter rules in the table.
Destination IP Filtering Destination IP Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256. Query Once you have specified the serial number, click on this button to display the filter rules. Delete Once you have specified the serial number, click on this button to delete the filter rules in the table.
Destination MAC Filtering Destination MAC Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256. Query Once you have specified the serial number, click on this button to display the filter rules. Delete Once you have specified the serial number, click on this button to delete the filter rules in the table.
Ether Type Filtering Ether Type Filtering Setup Label Description Filtering Type You can also select the filtering type here. No. From…To… Type in the range of serial number in the filter rule table. Valid number value: 1 ~ 256. Query Once you have specified the serial number, click on this button to display the filter rules. Delete Once you have specified the serial number, click on this button to delete the filter rules in the table.
4.3.3.2 VLAN Priority Remark This option allows you to configure the VLAN priority. From the Bridge menu, click on Access Control and then VLAN Priority Remark. The following page is displayed: Click on the VPRI Remark drop-down list and select a type of VLAN Priority Remark. Available options include Type of Service (TOS), IP Source, IP Destination, MAC Source, MAC Destination, VLAN ID, VLAN Priority Regeneration, Differentiated Services (DSCP), Protocol, and Ether Type.
TOS VLAN Priority Remark Setup - TOS Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete. Click on these drop-down list to select an ADSL bridge port or GIGA bridge port.
IP Source VLAN Priority Remark Setup – IP Source Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
IP Destination VLAN Priority Remark Setup – IP Destination Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
MAC Source VLAN Priority Remark Setup – MAC Source Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
MAC Destination VLAN Priority Remark Setup – MAC Destination Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
VLAN ID VLAN Priority Remark Setup – VLAN ID Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
VLAN Priority Regeneration VLAN Priority Remark Setup – VLAN Priority Regeneration Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
Differentiated Services VLAN Priority Remark Setup – Differentiated Services Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
af31 Assured Forwarding Class 3:Low Drop (bits:011010) af32 Assured Forwarding Class 3:Medium Drop (bits:011100) af33 Assured Forwarding Class 3:High Drop (bits:011110) af41 Assured Forwarding Class 4:Low Drop (bits:100010) af42 Assured Forwarding Class 4:Medium Drop (bits:100100) af43 Assured Forwarding Class 4:High Drop (bits:100110) ef Expedited Forwarding (bits:101110) Priority (Out) Click on the drop-down list and select the outgoing VLAN priority (0 ~ 7).
Protocol VLAN Priority Remark Setup – Protocol Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
Ether Type VLAN Priority Remark Setup – Ether Type Label Description VPRI Remark You can also select the priority remark type here. No. From …To… Type in the range of entry number in the table you want to view (value range is 1~256). Query To query entries, type in the entry number range and then click on this button to retrieve. Delete To delete entries, type in the entry number range and then click on this button to delete.
4.3.3.3 Rate Limit This option allows you to limit the rate of broadcast/multicast packets that are received on a VLAN, and configure the Three Color Marking (TCM) Policer profile. From the Bridge menu, click on Access Control and then Rate Limit. The following page is displayed. Click on the Rate Limit Type drop-down list and select the item you want to setup.
Rate Limit Flooding Rate Limit Flooding Setup Label Description Rate Limit Type Click on this drop-down list and select the item you want to setup. Flooding VID Type in VLAN ID (1 ~ 4094). The VLAN must have been created in the static VLAN table. Committed Information Rate Committed Information Rate (1536 ~ 1G bits per second). The threshold rate to turn on the rate-limit mechanism. Leaky Bucket Leaky bucket size. The unit is millisecond. This parameter ranges from 1 to 1024.
Rate Limit Policer profile The IDL-2402 supports two kinds of TCM Policer: two-rate TCM (with dual leaky buckets) and single-rate TCM (with single leaky bucket). The single-rate TCM meters a traffic stream and marks its packets according to Committed Information Rate (CIR) and Committed Burst Size (CBS) to be either green, or red. The single-rate TCM operates with a single leaky bucket that is updated according to only one rate, the committed information rate - CIR.
Rate Limit Poicer Setup Label Rate Limit Type Description Click on this drop-down list and select the item you want to setup. Click on this drop-down list and select a page to be displayed. Select Select the checkbox when you want to create/modify/delete this entry. Share mode: All the bridge ports which bind to the share mode policer profile will share the same Leaky Bucket defined by the CIR, EIR…parameters. So in Share mode, system only creates one Leaky Bucket for all the binding bridge ports.
Rate Limit Policer Binding Table The Rate Limit Policer Binding Table allows you to specify which Policer profile to bind and the binding status for a trunk or line bridge port. Rate Limit Policer Binding Setup Label Rate Limit Type Description Click on this drop-down list and select the item you want to setup. Click on these drop-down lists to select an ADSL bridge port or GIGA bridge port. Modify Once you have finished setting the parameter values, click on this button to submit the modification.
Three Color Marking Policer The IDL-2402 supports TCM Policer in accordance with the Metro Ethernet Forum (MEF) Bandwidth Profile and RFCs 2697 & 2698. Our TCM Policer supports both Color Aware and Color Blind modes. The “color” is used for determining whether a packet will proceed to the policer when TCM Policer works in Color Aware mode; also in the policer the packet may be remarked with new color according to the packet’s conformance to the policer rules.
Green Value Type in the green color value that is used when determining a packet’s input color (for Color Aware mode) or remarking a packet’s output color as green. Valid value is 0 ~ 7 for VLAN Priority color field or 0 ~ 63 for DSCP color field. Yellow Value Type in the yellow color value that is used when determining a packet’s input color (for Color Aware mode) or remarking a packet’s output color as yellow. Valid value is 0 ~ 7 for VLAN Priority color field or 0 ~ 63 for DSCP color field.
4.3.3.4 Priority Queue Mapping This web page is used to select SPQ/WFQ/WRR queuing mechanism and to setup the mapping between VLAN priority levels and system internal queues. From the Bridge menu, click on Access Control and then Priority Queue Mapping. The following page is displayed: The queues for Giga and ATM interfaces are different. Giga: The Giga interface has 4 Queues and these queues can only work on Strict Priority Queuing (SPQ) scheduling. The priorities of these queues are: Q3 > Q2 > Q1 > Q0.
4.3.4 Forwarding 4.3.4.1 TP Forwarding DB This option allows you to retrieve the status of the transparent forwarding database. The forwarding table will reveal the information of MAC addresses that are learned or statically configured on a specific bridge port. From the Bridge menu, click on Forwarding and then TP Forwarding DB. The following page is displayed. TP Forwarding DB Label Description Aging Time Type in the aging time in seconds.
4.3.4.2 Forwarding Static This option allows you to configure the static MAC address forwarding entries on a specific bridge port. The setting of static MAC address takes effect on egress direction of bridge port. From the Bridge menu, click on Forwarding and then Forwarding Static. The following page is displayed. Forwarding Static Label Description No. From…To… Select the range of entry number in the FDB to be retrieved. Valid number value: 1 ~ 512.
4.3.5 Relay 4.3.5.1 DSL Line Identify This option allows you to configure the DHCP option and PPPoE relay function. From the Bridge menu, click on Relay and then DSL Line Identify. The following page is displayed: DSL Line Identify Setup Label Description DSL Global Configuration PPP Service Name PPP Service Check mode Type in the PPPoE service name to add. Enable: the system will check whether the PPPoE service names from the Name PPPoE server and client are the same.
DSLAM Name mode: Select the DSLAM name to be customer-defined or cluster name (Domain name:NE name). DHCP Mode Click on this drop-down list and select OFF/ON to disable/enable DHCP relay function. ID Select Click on this drop-down list and select the Relay Agent Information that is inserted to the forwarding packets. Options are: Circuit ID, Remote ID, or Both. Circuit ID Type Click on this drop-down list and select the type of Circuit ID. Options are: DEFAULT, CUSTOMER.
4.3.6 IGMP 4.3.6.1 Protocol & Router Port This option allows you to setup the IGMP protocol and router port. From the Bridge menu, click on IGMP and then Protocol & Router Port. The following page is displayed: IGMP Router Port Setup Label Description Modify Click on this button to modify the IGMP configuration once you have set new values for the parameters. IGMP Version Select the IGMP version. Options are: IGMP OFF, IGMP V1, IGMP V2, and IGMP V3. IGMP Mode Select the IGMP mode.
Query 1~500(s) The Query Interval is the interval between General Queries sent by the Querier. By varying this value, an administrator may tune the number of IGMP messages on the network; larger values cause IGMP Queries to be sent less often. Value range is 1 ~ 500. Default is 125 seconds. URI 1~500(s) The Unsolicited Report Interval is the time between repetitions of a host's initial report of membership in a group. Value range is 1 ~ 500. Default: 1 second.
4.3.6.2 IGMP Profile This option allows you to configure the IGMP ACL (Access Control List) profile. This profile defines the IGMP multicast channels, which are allowed to join for each ADSL port. That is, a multicast stream will be copied to an ADSL port only if that multicast stream is registered in the ACL profile that is bound to this ADSL port. The maximum number of IGMP multicast channels in an ACL profile is 256.
Quickly IP Assign Type the IGMP group IP address here for quick assignment. Click on Assign button to put the value into the table. Then you can modify parts of the IP addresses directly in the table. Quickly VID Assign Type the IGMP group IP address here for quick assignment. Click on Assign button to put the value into the table. Assign Click on this button to apply the parameter values you have just entered. But these values haven’t been really saved in the database.
All select Click on this checkbox to select all ports in this page at one time. This is convenient for quickly value assignment. Quickly Max Group Assign This field is for quick value assignment (assign the same value to all the ports in current page at one time). Type in the maximum IGMP groups can be joined simultaneously per line port, and then click on Assign to put the value into the table. Quickly Profile ID Assign Click on this drop-down list to select the profile ID you want to bind.
4.3.6.3 IGMP Multicast This option allows you to query the IGMP multicast status. From the Bridge menu, click on IGMP and then IGMP Multicast. The IGMP Group page is displayed. Click on the IGMP Type drop- down list and select Group or Source. IGMP Type > Group: Click on List by drop-down list to select listing by entry number or listing by VID & IGMP group IP. List by Number: IGMP Group – List by Number Label Description No. From…To… Type in the entry number range in the table.
IGMP Type > Source: This option allows you to query the Source IP, which is the IP address of the source that is joining a multicast group on an interface. This option is available only when IGMP version 3 is selected for the system’s IGMP configuration (refer to section 4.3.6). IGMP Source Label Description VID Type in the VLAN ID (1~ 4094). Group IP Type in the IGMP group IP address. No. From…To… Type in the entry number range in the table.
4.3.7 IPOA 4.3.7.1 BRAS MAC The IDL-2402 supports an IPOA/IPOE IWF (Interworking Function). This option allows you to setup the BRAS MAC address that is used by the IPOA/IPOE IWF. From the Bridge menu, click on IPOA and then BRAS MAC. The following page is displayed. To add/modify a MAC: Select a checkbox beside an index and type in BRAS MAC address, and then click on Modify button. To delete a MAC: Select a checkbox (checkboxes) beside the index and then click on Delete button.
4.3.7.2 Interface Setup This option allows you to setup the interface for IPoA/IPoE IWF. From the Bridge menu, click on IPOA and then Interface Setup. The following page is displayed. Click on the radio button to select a circuit, set values for the parameters, and then click on Modify button. IPoA Interface Setup Label Description Click on the drop-down list and select the line ports to be listed. VPI Type in the VPI. Value range is 0 ~ 255. VCI Type in the VCI. Value range is 21, 32 ~ 65535.
Traffic (Rx/Tx) Click on the drop-down lists and select a traffic type for transmit and receive direction respectively. Available options are created in the ATM Traffic Descriptor page. See section 4.5.1. BRAS Click on the drop-down list and select a BRAS MAC. Available options are created in the IPoA BRAS MAC page. See section 4.3.7. Uplink Click on the drop-down list and select the uplink interface. Encap Select AAL5 Encapsulation Type: VCMUX/LLC Status Enable/Disable IPoA IWF.
4.4 ADSL 4.4.1 Profile 4.4.1.1 Service Main Profile This option allows you to configure the ADSL line service profile. From the ADSL menu, click on Profile and then Service Profile(main). The following page is displayed. ADSL Line Service Profile setup Label Description Select Index Click on the drop-down list and select the range of profile index. Options are: 0~10, 11~20, …, 111~120. Index This field shows the profile index.
Click on the drop-down list and select the Downstream Rate Adaptive Mode. Valid options are: Manual – Rate changed manually Rate Mode Downstream Init – Rate automatically selected at start up only and does not change after that Dynamic – Rate automatically selected at initialization and is continuously adapted during operation (show time). Click on the drop-down list and select the Upstream Rate Adaptive Mode.
4.4.1.2 Service Channel Profile This option allows you to configure the ADSL service channel profile. From the ADSL menu, click on Profile and then Service Profile(Channel). The following page is displayed. ADSL Service Channel Profile setup Label Select Index Index Description Click on the drop-down list and select the range of profile index. Options are: 1~5, 6~10, …, 116~120. This field shows the profile index.
Min Interval (sec) Margin for DownShift Min Interval. UpShift Noise Margin (dB)/Min Increase net data rate if Noise Margin is above the Upshift Noise Margin Interval (sec) for Upshift Min Interval. Interleaving MaxDelay Maximum interleaving delay (1~63 ms) IMP 0~8 (symbols) Minimum impulse noise protection (0.0~8.
4.4.1.3 Spectrum Main Profile This option allows you to configure the ADSL spectrum profile. From the ADSL menu, click on Profile and then Spectrum Profile(main). The following page is displayed. ADSL Spectrum Profile setup Label Description Click on the drop-down list and select the range of profile index. Select Index Options are: 1~4, 5~8, …, 117~120. Index This field shows the profile index. Click on the radio button beside the profile index to select the profile you want to modify or delete.
transition of L0 to L2 state or an L2 low power trim request. Value range is 0 ~ the value of L2 ATPRT (dB). L2 ATPRT Type in the total maximum aggregate transmit power reduction (in dB) that is allowed in the L2 state; the total reduction is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and L2 power trims. Value range is 0 ~ 15 (dB). Direction DS: downstream. US: upstream.
Click on this button to view/modify the current downstream/upstream Carrier Mask parameters. Input Carrier bit value and then click Apply.
Click on this button to view/modify Radio Frequency Interference (RFI) Bands data. Input the Start/Stop frequency, select the Ingress Level, Egress Control, Signal Type, and then click on the Apply button.
4.4.1.4 Spectrum ADSLx Profile This option allows you to configure the ADSL2/2+/READSL spectrum profile. From the ADSL menu, click on Profile and then Spectrum Profile(ADSLx). The following page is displayed. ADSL2/ReADSL/ADSL2+ Spectrum Profile Label Description Select Index Click on the drop-down list to select the range of profile index. Options are: 1~4, 5~8, …, 117~120. Index This field shows the profile index.
Only for ADSL2+. Valid options are: Standard/CA100/CA110/CA120/CA130/CA140/CA150/ PSD Shape CA160CA170/CA180/CA190/CA200/CA210/CA220/CA230/ CA240/CA250/CA260/CA270/CA280 PBO Power backoff operation mode (OFF/ON). Max Rx Aggr. Allowed PWR Maximum aggregate receive power over a set of subcarriers. It ranges from –25.5 to +25.5 dBm, with 0.1 dB steps.
4.4.1.5 TCA Profile This option allows you to setup the PM counter threshold for TCA (threshold crossing alert). From the ADSL menu, click on Profile and then TCA Profile. The following page is displayed. ADSL TCA Threshold setup Label Description Click on this drop-down list to select the page to be displayed. Modify Once you have typed in new threshold values, click on this button to submit the modification. Delete Click on this button to delete a selected profile (or profiles).
int LOL-NE Interval Loss of Link – near end int ErrFrm-NE/FE Interval Error Frame – near end/far end - 152 -
4.4.2 Data & Inventory 4.4.2.1 Inventory This option allows you to view the inventory of the ATUC and ATUR. From the ADSL menu, click on Data & Inventory and then Inventory. The following page is displayed. ADSL Inventory Label Description Click on this drop-down list and select the ports to be displayed. Atux Select ATUC or ATUR inventory to be displayed. Query To view inventory, click on this button once you have selected the port and ATUx.
4.4.2.2 Loop Test This option allows you to do the ADSL Dual End Loop Test. From the ADSL menu, click on Data & Inventory and then Loop Test. The following page is displayed. Click on the drop-down list and select the line port you want to test. Then click on Diagnostics Run to start a DELT. If you want to discontinue the test or make the loop go back to the normal state when the test has finished, just click on Diagnostics Abort.
Test completed: When the test has completed successfully, test result is displayed as follows.
- 156 -
- 157 -
4.4.2.3 Carrier Data This option allows you to view the ADSL line carrier data. From the ADSL menu, click on Data & Inventory and then Carrier Data. The following page is displayed. Select the line port (1 ~ 24) and carrier type (LOAD or GAIN). Then click on Query button. Note that if the line port is still in loop testing status, you cannot query the carrier data.
- 159 -
4.4.2.4 OP Data This option allows you to view the ADSL line/channel operational data and carrier data. From the ADSL menu, click on Data & Inventory and then OP Data. The following page is displayed. Line Operational Data: Click on ADSL OP Data drop-down list and select the item Line (OP). Then select the line port (1 ~ 24). Click on Query button.
Channel Operational Data: Click on ADSL OP Data drop-down list and select the item Channel (OP). Then select the port (1~24). Click on Query button. The following page is displayed.
4.4.3 Line Config & Info 4.4.3.1 Line Configuration This option allows you to setup the ADSL line configuration. From the ADSL menu, click on Line Config & Info and then Line Configuration. The following page is displayed. ADSL Line Configuration Label Description ADSL Port From…To… Type in the line port range. Valid number: 1 ~ 24. Operational Mask Mode Select the Operational Mode(s) to be masked. Select the modes in the block by using mouse and Shift or Ctrl key.
FORCE L3 Mode Click on this drop-down list and select ON to force the ADSL port to enter power management L3 mode (Idle state). Select the check box and then click on Modify button. Modify Click on this button to submit modification. Query Click on this button to display current line configuration.
4.4.3.2 Line Information This option allows you to setup the ADSL line information. From the ADSL menu, click on Line Config & Info and then Line Information. The following page is displayed. ADSL Line Information Label Description ADSL Port From…To… Type in the line port range. Valid number: 1~24. Modify Click on this button to submit the modification once you have entered new value for the ADSL line information.
4.5 Traffic 4.5.1 ATM Traffic Descriptor This option allows you to modify the traffic table. From the Traffic menu, click on ATM Traffic Descriptor. The following page is displayed: ATM Traffic Descriptor Setup Label Description PCR PCR stands for Peak Cell Rate (cells/second). CDVT CDVT stands for Cell Delay Variation Tolerance (microseconds). SCR SCR stands for Sustained Cell Rate (cells/second). MBS MBS stands for Maximum Burst Size (cells).
interfaces. For a similar traffic descriptor type that can be accepted at UNI 3.0 and UNI 3.1 interfaces, see "atmNoClpNoScr". [Policed VBR1] atmNoCLPScrCdvt: This traffic descriptor type is for no CLP with Sustained Cell Rate and CDVT. This traffic descriptor type is applicable to VBR connections following the UNI 3.0/3.1 conformance definition for PCR CLP=0+1 and SCR CLP=0+1. These VBR connections differ from VBR.1 connections in that the CLR objective applies only to the CLP=0 cell flow.
Create Click on this button to create a new traffic descriptor. Delete When you want to delete a traffic descriptor, click on the radio button beside the row number to select the traffic descriptor and then click on the Delete button. Note that the default profile cannot be deleted.
4.6 SNMP 4.6.1 SNMP Community This option allows you to configure the SNMP community that is the group that IDL-2402s and management stations running SNMP belong to. It helps define where information is sent. The community name is used to identify the group and serve as form of authentication. From the SNMP menu, click on SNMP Community. The following page is displayed. SNMP Community Setup Label Description Click on this button to create a new SNMP community.
4.6.2 SNMP Target This option allows you to configure the SNMP target to control where the SNMP traps (notifications) are sent. Traps are used to report an alarm or other asynchronous event about a managed IDL-2402 system. From the SNMP menu, click on SNMP Target. The following page is displayed. SNMP Community Setup Label Description Click on this button to create a new SNMP target. After you click on New, the following page is displayed.
Target No. Click on this drop-down list and select the SNMP target number. Query Select the target number and then click on this button to retrieve the information. Delete Select the target number and then click on this button to delete a target. Modify Select the target number and then click on this button to modify the target setting.
4.6.3 SNMP Notify This option allows you to setup the SNMP Notification (In SNMPv1, asynchronous event reports are called traps while they are called notifications in later versions of SNMP). From the SNMP menu, click on SNMP Notify. The following page is displayed. Table 0-2 SNMP Community Setup Label Notify No. Description This field shows the Notify number you select. Click on this button to create a new SNMP Notify. After you click on New, the following page is displayed.
4.7 Maintenance 4.7.1 SYS Log Server This option allows you to configure the IP address of the SYS Log server which listens for incoming Syslog messages. From the Maintenance menu, click on SYS Log Server. The following page is displayed. SYS Log Server Setup Label Description Current Server IP This field shows the IP address of current Sys Log server. Change Server Address Type in the new IP address of Sys Log server. The server must be a remote host.
4.7.2 Database This option allows you to import/export the configuration data. From the Maintenance menu, click on Database. The following page is displayed. Select the database configuration action you want to perform.
(A) Import File (Write Download Config To Flash): Type in the TFTP Server IP address and the name of the file you want to download. Then click on Get File button.
(B) Import File (Load Remote Config to Running Config) Type in the TFTP Server IP address and the name of the file you want to download. Then click on Get File button.
(C) Export File (Put Running Config to Remote TFTP Server) Type in the TFTP Server IP address and the name of the file you want to export. Then click on Put File button.
(D) Save Running Config to Flash (System Config) Click on the drop-down list and select partition, and then click on Write_Running button to write running configuration to Flash. Write running config to Flash successfully: (E) Reload Flash to Running Config Click on the drop-down list and select partition, and then click on LOAD_FLASH button to load configuration from Flash to Running Config.
(F) Restore Factory Default Click on Factory_Default button to restore factory default configuration. After loading default configuration to Flash successfully, you must click on RESTART button to restart the system so that the configuration can take effect.
(G) Flash Boot Point Configuration Select Click on the Boot Config drop-down list and select the partition (Partition1 or Partition2) as the boot point. Click on Apply button and then restart the system. The system will restart and load the configuration in the partition you select into the running configuration.
4.7.3 Firmware Update This option allows you to ftp get the firmware from a server and write to flash for updating the system firmware. From the Maintenance menu, click on Firmware Update. The following page is displayed. Firmware Update Label Description Firmware Update Once you have typed in the parameter values, click on this button to start firmware update. Remote FTP Server IP Type in the IP address of the FTP server. Server User Name Type in the ftp user name.
Partition Information This section displays the partition information including firmware version, updating date, and status (active or not). Note that active partition means the partition for next power-up, not current partition in use. You can refer to Current Version to know which partition is the current partition in use. When you update the firmware, new firmware will be written to the partition that is not currently in use.
Firmware Write successfully: When the Flash Write process has completed successfully, the Firmware Update Status shows “Firmware has upgraded already”. You can now restart the system.
4.7.4 ATM Loopbacks This option allows you to modify the ATM F4/F5 entries or send the diagnostic entry. From the Maintenance menu, click on ATM Loopbacks. The following page is displayed: ATM Loopbacks Setup Label OAM Cell Generation Description Click on the radio button to Disable/Enable OAM Cell Generation. Then click on Apply button to submit the setting. Click on the drop-down lists to select port range and PVC (1 ~ 8). Click on this button to create a loopback setting.
4.7.5 Fault Management 4.7.5.1 Alarm/Event This option allows you to query current alarm, history alarm, and event log. From the Maintenance menu, click on Fault Management and then Alarm/Event. The Current Alarm page is displayed. Click on the Alarm/Event Select drop-down list and select Current Alarm, History Alarm, or Event Log to view. Current Alarm: Type in the range of rows (1 ~ 1024) and then click on the Query button.
History Alarm: History Alarm Table Label Description Query Click on this button to query history alarms. Clear History Click on this button to clear the alarm history table. Row This field shows the row number. ID This field shows the alarm ID. Description This field shows the description for the alarm. This field shows the alarm level. Valid values are: Level MJ: major alarm. MN: minor alarm. State This field shows the alarm state: Set or Clear. Sequential Sequential number.
Event Log: Type in the range of rows and then click on the Query button. Event Log Label Description Query Click on this button to query most recent event log. Clear Event Click on this button to clear the event log. Row This field shows the row number. ID This field shows the event ID. Description This field shows the description for the event. Sequential Sequential number. Time Event occurring date and time.
4.7.5.2 Alarm Profile This option allows you to view and update the alarm profiles. From the Maintenance menu, click on Fault Management and then Alarm profile. The Alarm Profile page is displayed. Click on the Select Page drop-down list and select a page to display. To modify an alarm profile, click on the radio button beside the alarm ID, select the Level (Major/Minor), Mask/Unmask, and then click on the Modify button. You can also select the ALL ID checkbox to modify all alarm types at a time.
4.7.5.3 Hardware Temperature This page allows you to: view current system temperature set several temperature and time thresholds (see description in the following table) From the Maintenance menu, click on Fault Management and then Hardware Temp. The following page is displayed: Temperature Configuration Label Description Modify Click on this button to submit the update once you have entered all the new threshold values. Current Temperature (oC) This field shows the current system temperature.
4.7.6 Performance Monitoring 4.7.6.1 System Utilization This option allows you to monitor the memory utilization and network processor utilization. From the Maintenance menu, click on Performance Monitoring and then System Utilization. The following page is displayed.
4.7.6.2 Ethernet Statistics This option allows you to view the Gigabit Ethernet counter values for the trunk or line interface. From the Maintenance menu, click on Performance Monitoring and then Ethernet Statistics. Click on the leftmost drop-down list to select interface (giga port or DSL line port); if line interface is selected, you must further click on the middle and rightmost drop-down list to select the line port number and PVC number. At last, click on Query to get data of that interface.
ADSL line PVC: - 191 -
4.7.6.3 ATM Statistics This option allows you to query the ATM Statistics. From the Maintenance menu, click on Performance Monitoring and then ATM Statistics. The following page is displayed. Query ATM Statistics Label Description ADSL Port Click on this button to select line port. Auto Update Click on this checkbox to auto update the displayed statistics. Show Click on this drop-down list to select Tx, Rx, or All (Tx & Rx) data. Query Click on this button to query current statistics.
4.7.6.4 RMON This option allows you to configure and query the RMON Statistics. The IDL-2402 supports performance statistics defined in RMON MIB groups 1 (Ethernet statistics), 2 (history control), 3 (alarm), and 9 (event) per RFC 2819 for all network uplink ports. From the Maintenance menu, click on Performance Monitoring and then RMON. The following page is displayed. Select type of RMON table in the drop-down list.
ETH Statistics This option is for displaying the Ethernet interface RMON data. Click on the Data Source drop-down list and select GBE1. Type in an owner name and then click on New button to create a new ETH statistics entry. An owner is the entity that configured this entry and is therefore using the resources assigned to it. To modify an entry in this table, click on the index to select the entry, type in new value, and then click on Modify.
The following parameters are monitored in this table: RMON ETH Statistics variables Variable Description Rx DropEvents Monitoring rx dropped packets Rx Bytes Monitoring rx bytes packets Rx Packet Monitoring rx packets Rx BroadcastPkts Monitoring rx broadcast packets Rx MulticastPkts Monitoring rx multicast packets Rx CRC Align Errors Monitoring rx error aligment packets Rx Undersize Pkts Monitoring rx undersize packets Rx Oversize Pkts Monitoring rx oversize packets Rx Fragments Monitorin
History Control This table is for controlling the ETH History table (see next section). History Control 1 is for controlling ETH History table 1; History Control 2 is for controlling ETH History table 2; etc. Type in the Requested value and Interval (sec) and then click on New to create a History Control entry. Up to 10 History Control entries can be created. To modify an entry, click on the index to select the entry, type in new value, and then click on Modify.
ETH History This option is for displaying Ethernet interface RMON history data. Before a history table is available, you have to create a History Control entry in advance (see previous section). To query the History table, click on the History Index drop-down list and select a history table and then click on Query. RMON ETH History Table Label Description HistIndex This field shows the History Table index.
RMON ETH History variables Variable Description Rx DropEvents Monitoring Rx dropped packets Rx Bytes Monitoring Rx bytes packets Rx Packets Monitoring Rx packets Rx Broadcast Pkts Monitoring Rx broadcast packets Rx Multicast Pkts Monitoring Rx multicast packets Rx CRC Align Errors Monitoring Rx error alignment packets Rx Undersize Pkts Monitoring Rx undersize packets Rx Oversize Pkts Monitoring Rx oversize packets Rx Fragments Monitoring Rx fragments packets Rx Jabbers Monitoring Rx jab
Alarm This option allows you to configure the RMON alarm setting. This table controls the conditions on which alarms occur. Click on New to create an entry. To modify an entry, click on the index to select the entry, type in new value, and then click on Modify. To delete an entry, click on the index to select the entry and then click on Delete. RMON Alarm setup Label Description Interval The interval in seconds over which the data is sampled and compared with the rising and falling thresholds.
Set the alarm type that may be sent. Options are Rising, Falling, and Both. StartupAlarm Rising or Both: If the first sample after this entry becomes valid is greater than or equal to the Rising Threshold, then a single rising alarm will be generated. Falling or Both: If the first sample after this entry becomes valid is less than or equal to the Falling Threshold, then a single falling alarm will be generated. Value This field shows the value of the monitored data.
Another figure shows the example of RMON alarm for DELTA sample type. As shown in the following figure, the delta value varies high and low. The sample in T1 is the first one crossing the Rising Threshold, so an alarm occurs. No alarms will be generated afterwards until T5 sample which is crossing the Falling Threshold (note that the value of the previous sample, T4 sample, is greater than the Falling Threshold and the value of T5 sample).
Event This option allows you to configure the RMON event setting. Click on New to create an entry. To modify an entry, click on the index to select the entry, type in new value, and then click on Modify. To delete an entry, click on the index to select the entry and then click on Delete. RMON Event setup Label Description Description Type in comment describing the event. Community If an SNMP trap is to be sent, it will be sent to the SNMP community specified in this column.
LOG This option allows you to query the RMON LOG. Click on Query button to display the log. Only the event indices with LOG or LOGANDTRAP event type (see previous section) are possible to appear in the log.
4.6.7.5 ADSL Day/Interval This option allows you to query the ADSL PM 15-Min and Day Statistics. The IDL-2402 provides Today and Previous 1 day for Day PM, and also provides Current and Previous 1 ~ 96 interval for 15-Min PM. From the Maintenance menu, click on Performance Monitoring and then ADSL Day/Interval. The following page is displayed.
Port Click on the drop-down list and select a line port number (1 ~ 24). You can also select All and then click on More Port to select a port range to view the data of twelve ports at the same time. All Interval When you select to view a single port PM data, you can click on this checkbox to display the data of all intervals. Query Click on this button to get most recent data. Clear PM Click on this button to clear current PM data of the port you select.
5. CLI Command Reference Introduction Access to the Operations System (OS) /Network Element (NE) system is protected by a logon security system. You can log on to the NE with the user name and password. After three failed logon attempts, the system refuses further attempts. After you log on, the system monitors the interface for periods of inactivity. If the interface is inactive for too long, you are automatically logged off. All the NEs have the same initial user name (admin) and password (admin).
Screen Description Screen Description - 207 -
Execution Modes The CLI contains several execution modes. Users will see different set of commands under different execution modes. Table 5-1 lists all the execution modes and their purposes. When users enter a certain execution mode, the corresponding mode prompt will be displayed automatically on the screen. The mode prompts of all the execution modes are also listed in Table 5-1.
Getting help The user can get help in two ways. The first is by using the help command. The user can also enter a question mark ‘?’ at each position in the command. The displayed result depends on the execution mode and previous input. Terminal Key Function Following is the list of all the terminal keys and their function.
CTRL-t Drag the character before the cursor forward over the character at the cursor, moving the cursor forward as well. If the insertion point is at the end of the line, this transposes the last two characters of the line. Negative arguments have no effect. CTRL-u Kill backward from the cursor to the beginning of the current line. CTRL-w Kill the word behind point, using white space as a word boundary. The killed text is saved on the kill-ring.
Notation Conventions The notation conventions for the parameter syntax of each CLI command are as follows: Parameters enclosed in [ ] are optional. Parameter values are separated by a vertical bar “|” only when one of the specified values can be used. Parameter values are enclosed in { } when you must use one of the values specified. About String-type Parameters Some commands have string type parameters.
5.1 Global Commands The Global commands can be used in all execution modes. 5.1.1 bye Description Exit Syntax bye Parameter None 5.1.2 cluster Description Syntax Switch to a NE (network element) in the cluster cluster Parameter Name Description NE name in the cluster you want to switch to. Valid values: string type value. Default value: Type: Mandatory 5.1.3 cluster local Description Syntax Parameter Switch to Master in the cluster cluster local None 5.1.
5.1.7 help Description Syntax Parameter Display help help None 5.1.8 list Description Syntax Parameter Display all commands of current mode list None 5.1.9 list opmode Description Syntax Parameter List all the ADSL modes of operation. list opmode None 5.1.10 system contact Description Syntax Set system contact system contact Parameter Name Description System contact Valid values: string type value. Max 63 characters. Default value: Type: Optional 5.1.
5.1.12 system name Description Syntax Set system name system name Parameter Name Description System name Valid values: string type value. Max 32 characters. Default value: Type: Optional 5.1.
5.2 Initialize Mode Commands 5.2.1 enable Description Syntax Parameter Go to Enable execution mode from disable mode enable None 5.2.2 show license Description Syntax Parameter Display GNU software license show license None 5.2.3 show time Description Syntax Parameter Display current time show time None 5.2.4 show uptime Description Syntax Parameter Display System up time and CPU loading show uptime None 5.2.
5.3 Enable Mode Commands The commands in this section can be executed only in the Enable execution mode. 5.3.1 configure Description Syntax Parameter Go to Configure execution mode from Enable mode. configure None 5.3.2 ping Description Syntax ICMP echo and reply from hostname address or IP address. If no reply for a long time, you can press Ctrl + c to interrupt ping.
Default value: Type: Optional 5.3.5 show access-list dstmac Description Syntax Display all destination MAC address deny access list or by index show access-list dstmac [] Parameter Name Description Destination MAC deny access list number. Valid values: 1 ~ 256 Default value: Type: Optional 5.3.
5.3.8 show access-list ipprotocol Description Syntax Display all IP protocol deny access list or by index show access-list ipprotocol [] Parameter Name Description IP Protocol deny access list number. Valid values: 1 ~ 256 Default value: Type: Optional 5.3.9 show access-list l4dstport Description Syntax Display all L4 dest port deny access list or by index show access-list l4dstport [] Parameter Name Description L4 destination port deny access list number.
Default value: Type: Optional 5.3.12 show access-list srcmac Description Syntax Display all source mac address deny access list or by index show access-list srcmac [] Parameter Name Description Source MAC deny access list number. Valid values: 1 ~ 256 Default value: Type: Optional 5.3.13 show account Description Syntax Parameter Display system account list / detail information show account [detail] None 5.3.
5.3.18 show atmdesc Description Syntax Parameter Display ATM descriptor show atmdesc None 5.3.19 show atm-loopback Description Syntax Display ATM loopback status (by port) show atm-loopback [] Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Optional 5.3.20 show cli-config Description Syntax Parameter Display current setting for CLI configuration (timeout value, session value) show cli-config None 5.3.
5.3.24 show dot1x profile Description Syntax Parameter Display 802.1x profile show dot1x profile None 5.3.25 show dot1x server Description Syntax Parameter Display 802.1x server configuration show dot1x server None 5.3.26 show dot1x server Description Syntax Display 802.1x server configuration by index [1..3] show dot1x server Parameter Name Description Display 802.1x server configuration by index. Valid values: 1 ~ 3 Default value: Type: Mandatory 5.3.
5.3.29 show fdbstatic Description Syntax Display all static MAC forwarding table or by index show fdbstatic [] Parameter Name Description Static MAC forwarding table number. Valid values: 1 ~ 512 Default value: Type: Optional 5.3.30 show firmware Description Display firmware update status or partition information. Note: the ‘Active’ status of the firmware partition information means the active partition for next time restart, not current running partition. Ex.
5.3.33 show igmp Description Syntax Parameter Display IGMP information show igmp None 5.3.34 show igmp group Description Display IGMP VLAN group list Syntax show igmp group list show igmp group ip vlan show igmp group ip vlan src list show igmp group ip vlan src Parameter Name Description ipv4 address IGMP group address Valid values: 224.0.0.0 ~ 239.255.255.255 The range of addresses from 224.0.0.0 to 224.0.0.
5.3.36 show igmp-acl bind gigabit Description Syntax Display IGMP ACL bind status for gigabit interface show igmp-acl bind gigabit Parameter Name Description port Gigabit Ethernet port number Valid values: 1 Default value: Type: Optional 5.3.37 show igmp-acl bind xdsl Description Syntax Display IGMP ACL bind status for xdsl bridge port show igmp-acl bind xdsl Parameter Name Description port Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.39 show interface xdsl {all | } adsl carrier fe ds qln Description Syntax Display carrier information of far-end qln downstream by Bridge port (the xdsl port must be in diagnostic mode and the test is completed) show interface xdsl {all | } adsl carrier fe ds qln Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.42 show interface xdsl {all | } adsl carrier fe us load Description Syntax Display carrier information of far-end load upstream by Bridge port show interface xdsl {all | } adsl carrier fe us load Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.45 show interface xdsl {all | } adsl carrier ne us snr Description Syntax Display carrier information of near-end snr upstream by Bridge port (the xdsl port must be in diagnostic mode and the test is completed) show interface xdsl {all | } adsl carrier ne us snr Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.48 show interface xdsl {all | } adsl carrier ne us hlog Description Syntax Display carrier information of near-end hlog upstream by Bridge port (the xdsl port must be in diagnostic mode and the test is completed) show interface xdsl {all | } adsl carrier ne us hlog Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.51 show interface xdsl {all | } adsl carrier ne ds tss Description Syntax Display carrier information of near-end tss downstream by Bridge port (the xdsl port must be in diagnostic mode and the test is completed) show interface xdsl {all | } adsl carrier ne ds tss Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.54 show interface xdsl {all | } adsl line Description Syntax Display xDSL line status by Bridge port show interface xdsl {all | } adsl line Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.57 show interface xdsl {all | } adsl line information Description Syntax Display xDSL line information by Bridge port show interface xdsl {all | } adsl line information Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.60 show interface xdsl {all | } bridge Description Display Bridge information by Bridge port Syntax show interface xdsl {all | } bridge Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.
5.3.63 show interface xdsl {all | } ipoa Description Syntax Display IPoA (RFC 2684) information by Bridge port show interface xdsl {all | } ipoa Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.64 show interface xdsl {all | } vc Description Syntax Display VC information by Bridge port show interface xdsl {all | } vc Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.
5.3.67 show interface counter Description Syntax Parameter Display All interface Ethernet packet counter show interface counter None 5.3.68 show interface gigabit [] bridge Description Syntax Display Bridge information of the Gigabit Ethernet interface or by Gigabit Ethernet port show interface gigabit [] bridge Parameter Name Description port Gigabit Ethernet port number Valid values: 1 Default value: Type: Optional 5.3.
5.3.71 show mac-spoofing-detect config Description Syntax Parameter Display MAC Spoofing Detect configuration show mac-spoofing-detect config None 5.3.72 show mac-spoofing-detect log Description Syntax Parameter Display MAC Spoofing Detect log show mac-spoofing-detect log None 5.3.73 show management all Description Syntax Parameter Display all system management port ip setting show management all None 5.3.
5.3.76 show pm adsl interval Description Display performance monitoring data for previous 1~96 intervals or current interval Syntax show pm adsl interval { | current} Parameter Name Description port Port number Valid values: 1~24(48) Default value: Type: Mandatory number Interval number Valid values: 1~96 Default value: Type: Mandatory 5.3.77 show port-template parameter Description Syntax Parameter Display parameter mask.
5.3.79 show priority-list dstip Description Syntax Display destination IP address priority list show priority-list dstip [] Parameter Name Description number Destination IP address priority list number. Valid values: 1 ~ 256 Default value: Type: Optional 5.3.80 show priority-list dstmac Description Syntax Display destination MAC address priority list show priority-list dstmac [] Parameter Name Description number Destination MAC address priority list number.
Default value: Type: Optional 5.3.83 show priority-list srcip Description Syntax Display source IP address priority list show priority-list srcip [] Parameter Name Description number Source IP address priority list number. Valid values: 1 ~ 256 Default value: Type: Optional 5.3.84 show priority-list srcmac Description Syntax Display source MAC address priority list show priority-list srcmac [] Parameter Name Description number Source MAC address priority list number.
5.3.86 show priority-list vlanid Description Syntax Display VLAN ID priority list show priority-list vlanid [] Parameter Name Description number VLAN ID priority list number. Valid values: 1 ~ 256 Default value: Type: Mandatory 5.3.87 show priority-queue config Description Syntax Parameter Display Priority and Queue mapping configuration show priority-queue config None 5.3.88 show priority-regen Description Syntax Parameter Display VLAN priority tag filter show priority-regen None 5.3.
5.3.92 show profile service adsl Description Syntax Display ADSL service profile show profile service adsl { | all} Parameter Name Description Profile index Valid values: 1~120 Default value: Type: Optional 5.3.93 show profile spectrum adsl Description Syntax Display ADSL service profile show profile service adsl { | all} Parameter Name Description Profile index Valid values: 1~120 Default value: Type: Optional 5.3.
5.3.95 show rmon alarm Description Syntax Display RMON alarm information show rmon alarm {all | } Parameter Name Description number RMON alarm entry index. Valid values: 1 ~ 64 Default value: Type: Mandatory 5.3.96 show rmon ether_history Description Syntax Display RMON Ether history information show rmon ether_history Parameter Name Description number RMON index. Valid values: 1 ~ 10 Default value: Type: Mandatory 5.3.
Default value: Type: Mandatory 5.3.99 show rmon log DescriptionDisplay RMON log Syntax Parameter show rmon log None 5.3.100 show rmon statistic Description Syntax Display RMON statistic information show rmon statistic {all | } Parameter Name Description number RMON statistic entry index. Valid values: 1 ~ 10 Default value: Type: Mandatory 5.3.101 show route Description Syntax Parameter Display GBE routing table and default gateway show route None 5.3.
5.3.104 show runningcfg interface xdsl Description Syntax Display running config by XDSL interface show runningcfg interface xdsl Parameter Name Description port XDSL Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.3.105 show snmp Description Syntax Parameter Display SNMP community/notify/target setting show snmp {community | notify | target} None 5.3.106 show sntp Description Syntax Parameter Display SNTP setting show sntp None 5.3.
5.3.111 show temperature Description Syntax Parameter Display system temperature show temperature None 5.3.112 show time Description Syntax Parameter Display current time show time None 5.3.113 show uptime Description Syntax Parameter Display System up time and CPU loading show uptime None 5.3.114 show version Description Syntax Parameter Display CLI software version show version None 5.3.
5.3.117 show vlan ethertype Description Syntax Parameter Show VLAN S-Tag Ether type show vlan ethertype None 5.3.118 show vlan protocol-base Description Syntax Parameter Display protocol based VLAN table show vlan ethertype None 5.3.119 show vlan-translation one-to-one Description Syntax Parameter Display one-to-one VLAN translation table show vlan-translation one-to-one None 5.3.
5.4 Configure Mode Commands The commands in this section can be executed only in the Configure execution mode. 5.4.1 access-list Description Syntax Parameter Go to access-list execution mode from Configure mode. access-list None 5.4.
Set password expiration days (0:disable) Default value: Type: Optional 5.4.3 account delete Description Syntax Delete account account delete Parameter Name Description ID name (max 31 characters) Default value: Type: Mandatory 5.4.
Default value: Type: Optional 5.4.5 aging Description Syntax Bridge aging time aging Parameter Name Description number Aging time (sec). Valid values: (10~1000000) sec. Default value: 300 Type: Mandatory 5.4.6 alarm event clear Description Syntax Parameter Clear alarm event log alarm event clear None 5.4.7 alarm history clear Description Clear alarm history Syntax alarm history clear Parameter None 5.4.
Default value: Type: Mandatory PVC number Valid values: 1~8 Default value: Type: Mandatory ATM loopback type Valid values: f5-e2e, f5-segment Default value: Type: Mandatory 5.4.10 cli-config session Description Syntax Set CLI max number of connection sessions cli-config session Parameter Name Description Set CLI max number of connection sessions Valid values: 1~10 Default value: 5 Type: Mandatory 5.4.
Valid values: (max length 31) Default value: Type: Mandatory 5.4.13 cluster-cfg management Description Syntax Set cluster management IP configuration cluster-cfg management {ip | netmask | gateway } Parameter Name Description IP address. Valid values: xxx.xxx.xxx.xxx Default value: 0.0.0.0 Type: Mandatory (xxx:0~255) Netmask of the management port. Valid values: xxx.xxx.xxx.xxx Default value: Type: Optional (xxx:0~255) 5.4.
5.4.16 cluster-cfg voting-key Description Syntax Set cluster voting-key for the priority to be a Master cluster-cfg voting-key Parameter Name Description Cluster voting key. Valid values: 0 ~ 4294967295 Default value: 0 Type: Mandatory 5.4.17 dot1x Description Go to 802.1x configuration mode Syntax dot1x Parameter None 5.4.18 dot1x disable Description Syntax Parameter disable 802.1x authentication function of the system dot1x disable None 5.4.
5.4.22 dsl-line-identify dhcp option82 dslam-name Description Syntax Set DSLAM name dsl-line-identify dhcp option82 dslam-name Parameter Name Description Set DSLAM name (max length 15) Default value: Type: Mandatory 5.4.23 dsl-line-identify dhcp option82 dslam-name-cluster Description Syntax Parameter Set DSLAM name by Cluster name dsl-line-identify dhcp option82 dslam-name-cluster None 5.4.
5.4.27 dsl-line-identify pppoe srv-name Description Syntax Set Service Name dsl-line-identify pppoe srv-name Parameter Name Description Set Service name Default value: Type: Mandatory 5.4.28 dsl-line-identify pppoe srv-name-check Description Syntax Parameter Disable/Enable PPPoE Service Name check dsl-line-identify pppoe srv-name-check {disable | enable} None 5.4.
MAC address Valid values: xx:xx:xx:xx:xx:xx Default value: Type: Mandatory (xx:00~ff) 5.4.30 fdbstatic disable Description Syntax Disable specify static MAC forwarding entry fdbstatic disable Parameter Name Description Static MAC forwarding table number Valid values: 1~512 Default value: Type: Mandatory 5.4.
5.4.33 firmware login Description Syntax Login FTP server that firmware image belongs to firmware login username password Parameter Name Description IPV4 address Valid values: xxx.xxx.xxx.xxx Default value: Type: Mandatory (xxx:0~255) User name (max 31 characters) Default value: Type: Mandatory Input password (max 31 characters) Default value: Type: Mandatory 5.4.
5.4.36 http port Description Syntax Set http server listening port http port Parameter Name Description port number The port number. Valid values: Integer range 0-65535 Default value: 80 Type: Mandatory 5.4.37 igmp acl Description Syntax Parameter IGMP ACL control mode igmp acl {enable | disable} None 5.4.38 igmp default Description Syntax Parameter IGMP set default igmp [default] None 5.4.
5.4.42 igmp proxy Description Syntax Parameter Enable GMP proxy snooping mode igmp proxy None 5.4.43 igmp snooping Description Syntax Parameter Enable IGMP normal snooping mode igmp snooping None 5.4.
5.4.46 igmp timeout Description Syntax IGMP timeout setting (BC/LMQT/MRT/Query/URI) igmp timeout {bc | lmqt | mrt | query | uri} Parameter Name Description Timeout value Valid values: 1~500 (second) Default value: BC: 400 LMQT: 1 MRT: 10 Query: 125 URI: 1 Type: Mandatory 5.4.47 igmp version Description Set IGMP protocol version Syntax Parameter igmp version {v1 | v2 | v3} None 5.4.
5.4.50 mac-spoofing-detect Description Syntax Parameter Enable/Disable MAC spoofing detection mac-spoofing-detect {enable | disable} None 5.4.51 mac-spoofing-detect log Description Syntax Parameter Enable/Disable MAC spoofing detection log mac-spoofing-detect log {enable | disable} None 5.4.52 management gbe Description Syntax Set GBE port IP address management gbe Parameter Name Description ipv4 address IP address. Valid values: xxx.xxx.xxx.xxx Default value: 0.0.0.
5.4.54 management gbe vlan priority Description Syntax Set priority level of the inband management traffic sent out from GBE port management gbe vlan priority Parameter Name Description Priority ID Valid values: 0 ~ 7 Default value: 0 Type: Mandatory 5.4.55 pm clear Description Syntax Clear current performance monitoring data. pm clear Parameter Name Description Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.4.
5.4.58 port-template template-port Description Syntax Select the template line port and pasted line port (copy configuration from template port) port-template template-port paste-port Parameter Name Description XDSL Port number Valid values: 1~24(48) Default value: Type: Mandatory 5.4.59 priority-list Description Syntax Parameter Go to Priority-list execution mode from Configure mode. priority-list None 5.4.
5.4.62 priority-queue atm queue1-weight Description Syntax Set weight value of ATM Priority Queue 1 priority-queue atm queue1-weight Parameter Name Description Weight value of ATM Priority Queue 1 Valid values: 1 ~ 255 Default value: 20 Type: Mandatory 5.4.
5.4.66 priority-queue gigabit priority Description Syntax Set gigabit interface priority queue mapping priority-queue atm priority queue Parameter Name Description Priority ID Valid values: 0 ~ 7 Default value: 0 Type: Mandatory Priority queue value. Valid values: 0 ~ 3 Default value: Type: Mandatory 5.4.67 profile alarm Description Syntax Parameter Enter this command to go to alarm profile configuration mode. profile alarm None 5.4.
Default value: Type: Mandatory 5.4.70 profile spectrum Description Syntax [disable] Enter this command to go to spectrum profile configuration mode or delete a spectrum profile profile spectrum {adsl2 | adsl2plus | readsl2} Parameter Name Description profile index Profile index Valid values: 2 ~ 120 Default value: Type: Mandatory 5.4.
5.4.73 remotecfg login Description Login FTP server to get remote configuration and load it to running configuration or write remote configuration to memory Syntax remotecfg login get {load | write partition } Parameter Name Description IP address of TFTP server. Valid values: xxx.xxx.xxx.
Default value: Type: Mandatory 5.4.76 rmon alarm delete Description Delete RMON alarm entry Syntax rmon alarm delete Parameter Name Description RMON alarm entry index Valid values: 1~64 Default value: Type: Mandatory 5.4.
RMON alarm falling threshold Valid values: 0~4294967295 Default value: Type: Mandatory 5.4.79 rmon alarm owner Description Syntax RMON alarm owner rmon alarm owner Parameter Name Description Owner name. Valid values: (max 31 characters) Default value: Type: Mandatory 5.4.
Default value: Type: Mandatory RMON alarm rising threshold Valid values: 0~4294967295 Default value: Type: Mandatory 5.4.82 rmon alarm sample_type Description RMON alarm sample type (Compared directly with the thresholds or Difference compared with the thresholds) Syntax rmon alarm sample_type {absolute | delta} Parameter Name Description RMON alarm entry index Valid values: 1~64 Default value: Type: Mandatory 5.4.
rx_fragments Monitoring rx fragments packets rx_jabber Monitoring rx jabber packets rx_multicast Monitoring rx multicast packets rx_oversize Monitoring rx oversize packets rx_packets Monitoring rx packets rx_undersize Monitoring rx undersize packets tx_single_collision Monitoring tx single collision packets txrx_frames_64 Monitoring tx 64 octets txrx_frames_127 Monitoring tx 65 to 127 octets txrx_frames_255 Monitoring tx 128 to 255 octets txrx_frames_511 Monitoring tx 256 to 511 octets t
Valid values: 1~128 Default value: Type: Mandatory RMON event community Valid values: string type value. (max 31 characters) Default value: Type: Mandatory 5.4.86 rmon event delete Description Syntax Delete RMON event entry rmon event delete Parameter Name Description RMON event entry index Valid values: 1~128 Default value: Type: Mandatory 5.4.
5.4.88 rmon event owner Description Syntax Set RMON event owner rmon event owner Parameter Name Description RMON event entry index Valid values: 1~128 Default value: Type: Mandatory Owner name Valid values: string type value. (max 31 characters) Default value: Type: Mandatory 5.4.
Valid values: 1~65535 Default value: Type: Mandatory 5.4.91 rmon history delete Description Syntax Delete RMON history entry rmon history delete Parameter Name Description RMON history control entry index Valid values: 1~10 Default value: Type: Mandatory 5.
Type: Mandatory History interval Valid values: 1~3600 (sec) Default value: Type: Mandatory 5.4.94 rmon history owner Description Syntax Set RMON history owner rmon history owner Parameter Name Description RMON history control entry index Valid values: 1~10 Default value: Type: Mandatory Owner name Valid values: string type value. (max 31 characters) Default value: Type: Mandatory 5.4.
5.4.96 rmon statistic ifc Description Syntax Set Physical interface rmon statistic ifc Parameter Name Description RMON history control entry index Valid values: 1~10 Default value: Type: Mandatory Physical interface index Valid values: 1~2 Default value: Type: Mandatory 5.4.
Valid values: xxx.xxx.xxx.xxx Default value: Type: Mandatory (xxx:0~255) 5.4.99 route default Description Syntax Set default route route default Parameter Name Description Default route IP address. Valid values: xxx.xxx.xxx.xxx Default value: Type: Mandatory (xxx:0~255) 5.4.100 route delete Description Syntax Delete routing from route table route delete netmask Parameter Name Description IP address. Valid values: xxx.xxx.
5.4.102 runningcfg load partition Description Syntax Load running configuration from memory runningcfg load partition Parameter Name Description Partition number Valid values: 1~2 Default value: Type: Mandatory 5.4.103 runningcfg login Description Syntax Login FTP server runningcfg login put Parameter Name Description IP address of TFTP server. Valid values: xxx.xxx.xxx.
SNMP community index Valid values: 1~32 Default value: Type: Mandatory Community string. (max 31 character; note that community names beginning with a digital number are not allowed) Default value: public Type: Mandatory 5.4.106 snmp notify DescriptionSet SNMP notify information / Delete SNMP notify tag Syntax snmp notify {tag | delete} Parameter Name Description Notify name string. (max 31 characters) Default value: Type: Mandatory Notify Tag string.
Default value: 162 Type: Mandatory 5.4.108 snmp target delete Description Delete SNMP target tag list Syntax snmp target delete Parameter Name Description SNMP target name Valid values: (max 31 characters) Default value: Type: Mandatory 5.4.
5.4.111 sntp polling interval Description Syntax Set SNTP polling interval sntp polling interval Parameter Name number Description Polling interval (in seconds) Valid values: 60~65535 Default value: 600 Type: Mandatory 5.4.112 sntp server address Description Syntax Set SNTP server ip address snmp server address Parameter Name Description IP address of SNTP server. Valid values: xxx.xxx.xxx.xxx Default value: 0.0.0.0 Type: Mandatory (xxx:0~255) 5.4.
5.4.115 tcm color-field Description Syntax Parameter Set TCM color field to be VLAN priority or DSCP. tcm color-field {vprio | dscp} None 5.4.116 tcm green Description Syntax Set TCM green color value tcm green Parameter Name Description TCM green color value Valid values: 0 ~ 7 for VLAN priority color field; 0 ~ 63 for DSCP color field Default value: 1 Type: Mandatory 5.4.
5.4.119 tcm yellow Description Syntax Set TCM yellow color value tcm yellow Parameter Name Description TCM yellow color value Valid values: 0 ~ 7 for VLAN priority color field; 0 ~ 63 for DSCP color field Default value: 3 Type: Mandatory 5.4.120 temperature threshold Description Syntax Shelf temperature threshold temperature threshold {up | down | fan} Parameter Name Description Temperature threshold value.
5.4.122 time set date Description Syntax Set date of the system (default is current system date) time set date {MM-DD-YY | MM-DD-CCYY} Parameter Name Description MM Month. Valid values: 01-12 Type: Mandatory DD Day of month. Valid values: 01-31 Type: Mandatory CC Century. Valid values: 0 Type: Optional YY Short year start from 2000. Valid values: 00-99 Type: Mandatory 5.4.
5.4.124 time set timezone Description Syntax Set timezone time set timezone Parameter Name Description timezone Timezone Type: Mandatory Valid values: Given below.
wadt wst jst kst cast sast jdt gst east cadt sadt eadt nzt nzst idle nzdt (GMT+08:00) West Australian Daylight Time (GMT+08:00) WST (GMT+09:00) Japan Standard Time (GMT+09:00) Korean Standard Time (GMT+09:30) Central Australian Standard Time (GMT+09:30) South Australian Standard Time (GMT+10:00) JDT (GMT+10:00) Guam Standard Time (GMT+10:00) East Australian Standard Time (GMT+10:30) Central Austrlian Daylight Time (GMT+10:30) South Australian Daylight Time (GMT+11:00) East Australian Daylight Time (GMT+12:
5.4.127 vlan-translation / gigabit one-to-one Description Set one-to-one VLAN translation Syntax 1. C-tag reserved vlan-translation / gigabit one-to-one reserved {priority-reserved | priority-replaced } 2. C-tag replaced vlan-trans vlan-translation / gigabit one-to-one replaced {priority-reserved | priority-replaced } 3.
specified value. Valid values: 0 ~ 7 Default value: Type: Mandatory 5.4.128 vlan-translation / gigabit many-to-one Description Syntax Set many-to-one VLAN translation vlan-translation / gigabit many- to-one replaced {priority-reserved | priority-replaced } Parameter Name Description Port number.
5.4.129 vlan-translation / disable Description Syntax Delete the specified entry from the VLAN translation table. vlan-translation / disable Parameter Name Description ADSL Port number.
5.5 Ethernet Interface Mode Commands The commands in this section can be executed only in the Ethernet Interface execution mode. 5.5.1 bridge Description Syntax Parameter Enter bridge configuration mode / Set bridge port to default status bridge [default] None 5.5.2 gbe admin Description Syntax Parameter Set Gigabit Ethernet administrative status (ON/OFF) gbe admin {on | off} None 5.5.
5.6 Interface Mode Commands The commands in this section can be executed only in the Interface execution mode. 5.6.1 bridge Description Syntax Enter ATM-bridge configuration mode / Disable bridge port bridge [disable] Parameter Name Description bridge id Bridge number. Valid values: 1-8 Default value: 1 Type: Mandatory 5.6.2 adsl-config Description Syntax Parameter Enter adsl configuration mode adsl-config None 5.6.
5.7 ATM Bridge Mode Commands The commands in this section can be executed only in the ATM Bridge execution mode. 5.7.1 accfrm Description Syntax Parameter Set acceptable frame type (untagged only, tagged only, or all) accfrm {all | tag | untag} None 5.7.2 accounting disable Description Syntax Parameter Disable accounting after authentication accounting disable None 5.7.3 accounting enable Description Syntax Parameter Enable accounting after authentication accounting disable None 5.7.
5.7.6 auth-sever-timeout Description Syntax 802.1x Timeout for Radius Retries auth-server-timeout Parameter Name Description Timeout for Radius Retries Valid values: 1 ~ 65534 Default value: 60 Type: Mandatory 5.7.7 auth-supp-timeout Description Syntax 802.1x Timeout for requesting the supplicant to retry auth-supp-timeout Parameter Name Description Timeout for Supplicant retries Valid values: 1 ~ 65534 Default value: 60 Type: Mandatory 5.7.
5.7.9 default vlan Description Syntax Set default VLAN ID for a bridge port default vlan Parameter Name Description VLAN ID Valid values: 1 ~ 4094 Default value: 1 Type: Mandatory 5.7.10 default prio Description Syntax Set default priority value for a bridge port default prio Parameter Name Description Priority ID Valid values: 0 ~ 7 Default value: 0 Type: Mandatory 5.7.
5.7.12 egress Description Default PVID egress taged/untagged setting Syntax egress {tag | untag} Parameter None 5.7.13 force priority Description Force priority setting (disabled: reserve the original priority of all packets. egress: force the priority value of all packets sent out from this bridge port’s default VLAN to be the default VLAN priority, so this rule only works on default VLAN of this bridge port.
5.7.16 ingress Description Syntax Parameter Enable/disable ingress filter mode ingress {enable | disable} None 5.7.17 interim-interval Description Syntax 802.1x Timeout for Accounting Information Update interim-interval Parameter Name Description Timeout for Accounting Information Updated. Valid values: 60 ~ 600 Default value: 300 Type: Mandatory 5.7.
5.7.21 max-reauth-req Description Syntax 802.1x Max No. of Retries to supplicant (sending requests to the authentication server if no response is received) max-reauth-req Parameter Name Description Max number of retries. Valid values: 1~ 10 Default value: 2 Type: Mandatory 5.7.22 max-req Description Syntax 802.1x Max No.
5.7.24 port-control auto Description Auto (default) Syntax Set to the system default authentication state for the port Parameter none 5.7.25 port-control force-authorized Description Force this port authorized state Syntax port-control force-authorized Parameter none 5.7.26 port-control force-unauthorized Description Force this port unauthorized state Syntax port-control force-unauthorized Parameter none 5.7.
5.7.29 pvc Description Syntax Set VPI and VCI pvc / Parameter Name Description Virtual Path Identifier. Valid values: 0 ~ 255 Default value: 0 Type: Mandatory Virtual Channel Identifier. Valid values: 21, 32~65535 Default value: 35 Type: Mandatory 5.7.30 pvc atmdesc Description Syntax Parameter List ATM traffic descriptor pvc atmdesc None 5.7.
5.7.32 pvc atmdesc shp Description Syntax Set ATM shaped (Tx) descriptor pvc atmdesc shp Parameter Name Description ATM descriptor number. Valid values: Enter ‘pvc atmdesc’ command to see the descriptor list. Default value: Type: Mandatory 5.7.33 pvc encapsulation Description Syntax Parameter Set Encapsulation type pvc encapsulation {llc | vcmux | auto} None Note: The IDL-2402 supports auto-detection of the ATM AAL5 encapsulation method, LLC or VC-Mux.
Valid values: 1~ 65534. Default value: 60 Type: Mandatory 5.7.35 reauthentication disable Description Syntax Parameter Disable Reauthentication for this port reauthentication disable none 5.7.36 reauthentication enable Description Syntax Parameter Enable Reauthentication for this port reauthentication enable none 5.7.37 reauth-period Description Syntax 802.
5.7.40 tcm-policer Description Syntax Bind/Unbind Three Color Marking (TCM) Policer profile tcm-policer {bind | unbind} Parameter Name Description TCM policer profile index. Valid values: 1~24(48) Default value: Type: Mandatory 5.7.41 vlan disable Description Syntax Delete a VLAN from memberset table vlan disable Parameter Name Description VLAN ID VLAN ID. Valid values: 1 ~ 4094 Default value: Type: Mandatory 5.7.
5.7.43 vlan priority Description Syntax Set VLAN memberset priority (specify priority level or reserved the original priority, tag or untag, enable or disable port isolation) vlan priority { | reserved} {tag | untag} isolation [disable] Parameter Name Description VLAN ID VLAN ID. Valid values: 1 ~ 4094 Default value: Type: Mandatory Priority ID Valid values: 0 ~ 7 Default value: 0 Type: Mandatory 5.7.
5.8 GBE Bridge Mode Commands The commands in this section can be executed only in the GBE Bridge execution mode. 5.8.1 accfrm Description Syntax Parameter Set acceptable frame type (untagged only, tagged only, or all) accfrm {all | tag | untag} None 5.8.2 default vlan Description Syntax Set default VLAN ID for a bridge port default vlan Parameter Name Description VLAN ID Valid values: 1 ~ 4094 Default value: 1 Type: Mandatory 5.8.
5.8.5 ingress Description Syntax Parameter Enable/disable ingress filter mode ingress {enable | disable} None 5.8.6 isolation Description Syntax Parameter Enable/Disable default PVID isolation setting isolation [disable] None 5.8.7 link mode Description Syntax Parameter Set link mode (uplink mode or user mode) link mode {uplink | user} None 5.8.
Valid values: 0 ~ 7 Default value: Type: Mandatory Outgoing VLAN priority value Valid values: 0 ~ 7 Default value: Type: Mandatory 5.8.10 stack Description Syntax Parameter Enable/disable VLAN stacking stack {enable | disable} None 5.8.11 tcm-policer Description Syntax Bind/Unbind Three Color Marking (TCM) Policer profile tcm-policer {bind | unbind} Parameter Name Description TCM policer profile index. Valid values: 1~24(48) Default value: Type: Mandatory 5.8.
5.8.13 vlan list Description Syntax Show memberset setting by VLAN vlan list Parameter Name Description VLAN ID VLAN ID. Valid values: 1 ~ 4094 Default value: Type: Mandatory 5.8.
5.9 GBE-LA Bridge Mode Commands 5.9.1 accfrm Description Syntax Parameter Set acceptable frame type (untagged only, tagged only, or all) accfrm {all | tag | untag} None 5.9.2 default vlan Description Syntax Set default VLAN ID for a bridge port default vlan Parameter Name Description VLAN ID Valid values: 1 ~ 4094 Default value: 1 Type: Mandatory 5.9.
5.9.5 ingress Description Syntax Parameter Enable/disable ingress filter mode ingress {enable | disable} None 5.9.6 isolation Description Syntax Parameter Enable/Disable default PVID isolation setting isolation [disable] None 5.9.7 link mode Description Syntax Parameter Set link mode (uplink mode or user mode) link mode {uplink | user} None 5.9.
Default value: Type: Mandatory Outgoing VLAN priority value Valid values: 0 ~ 7 Default value: Type: Mandatory 5.9.10 stack Description Syntax Parameter Enable/disable VLAN stacking stack {enable | disable} None 5.9.11 tcm-policer Description Syntax Bind/Unbind Three Color Marking (TCM) Policer profile tcm-policer {bind | unbind} Parameter Name Description TCM policer profile index. Valid values: 1~24(48) Default value: Type: Mandatory 5.9.
5.9.13 vlan list Description Syntax Show memberset setting by VLAN vlan list Parameter Name Description VLAN ID VLAN ID. Valid values: 1 ~ 4094 Default value: Type: Mandatory 5.9.
5.10 ADSL Configure Mode Commands The commands in this section can be executed only in the ADSL Config mode. 5.10.1 line mode carrier Description Syntax Parameter Set/Clear xDSL line carrier line mode carrier {on | off | oninit} None 5.10.2 line mode diagnostic Description Syntax Parameter Set/Clear xDSL line diagnostics line mode diagnostic {init | off} None 5.10.3 line mode force-l3 Description Syntax Parameter Set force to power management L3 mode or not line mode force-l3 {on | off} None 5.10.
5.10.5 line port Description Syntax Set xDSL line port information line port {id | description | phone } Parameter Name Description Line ID name (max 32 characters) Default value: Type: Mandatory Line port description (max 48 character) Default value: Type: Mandatory Phone number. (max 32 characters) Valid values: no limit format Default value: Type: Mandatory 5.10.
5.11 IPoA Configure Mode Commands The commands in this section can be executed only in the IPoA configure mode. 5.11.1 brasmac Description Syntax Display Broadband RAS MAC address by index brasmac Parameter Name Description Broadband RAS MAC Table Index Valid values: 1 ~ 48 Default value: Type: Mandatory 5.11.2 brasmac list Description Syntax Parameter Show Broadband RAS MAC address table brasmac list None 5.11.
5.11.4 cvlan Description Syntax Customer VLAN setting cvlan Parameter Name Description Customer VLAN ID number Valid values: 1 ~ 4094 Default value: Type: Mandatory 5.11.5 ipoa-status Description Syntax Parameter IPoA Status setting (enable/disable IPoA) ipoa-status {enable | disable} None 5.11.
Virtual Channel Identifier. Valid values: 21, 32~65535 Default value: 35 Type: Mandatory 5.11.8 pvc atmdesc Description Syntax Parameter List ATM traffic descriptor pvc atmdesc None 5.11.9 pvc atmdesc plc Description Syntax Set ATM police (Rx) descriptor pvc atmdesc plc Parameter Name Description ATM descriptor number. Valid values: Enter ‘pvc atmdesc’ command to see the descriptor list. Default value: Type: Mandatory 5.11.
5.11.11 pvc encapsulation Description Syntax Parameter Set Encapsulation type pvc encapsulation {llc | vcmux} None 5.11.12 uplink gigabit Description Syntax Set GBE uplink mode uplink Parameter Name Description Gigabit Ethernet port number.
5.12 Access List Mode Commands The commands in this section can be executed only in the ACL execution mode. 5.12.1 bcrate cir Description Syntax Broadcast rate limiting CIR and LBS setting bcrate cir lbs Parameter Name Description Committed Information Rate (bps) Valid values: 1536 ~ 1000000000 Default value: 80000 Type: Mandatory Leakage Bucket Size (millisecond) Valid values: 1 ~ 1024 Default value: 80 Type: Mandatory 5.12.
Valid values: 1~256 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Destination MAC address Valid values: xx:xx:xx:xx:xx:xx (xx:00~ff) Default value: 00:00:00:00:00:00 Type: Mandatory 5.12.4 dstmac list Description Syntax Parameter Display destination MAC deny access list dstmac list None 5.12.
Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Destination IP address Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: 0.0.0.0 Type: Mandatory Subnet mask Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: Type: Optional 5.12.
Name Description Ether Type deny access list number Valid values: 1~256 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Ether Type value Valid values: 0x0001 ~ 0xffff Default value: Type: Mandatory 5.12.8 ethertype list Description Syntax Parameter Display Ether Type deny access list ethertype list None 5.12.
Valid values: 1~256 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Allowed source IP address Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: 0.0.0.0 Type: Mandatory IP Allowed entry VLAN ID number Valid values: 1 ~ 4094 Default value: Type: Optional 5.12.
Name Description IP Protocol deny access list number Valid values: 1-256 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory protocol Input protocol name.
5.12.12 ipprotocol list Description Syntax Parameter Display IP protocol deny access list ipprotocol list None 5.12.
5.12.14 l4dstport list Description Syntax Parameter Display L4 dest port deny access list l4dstport list None 5.12.15 mcfldrate list Description Syntax Parameter Display flooding rate limiting list mcfldrate list None 5.12.
srcip list srcip disable Parameter Name Description Source IP deny access list number Valid values: 1~256 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Destination IP address Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: 0.0.0.0 Type: Mandatory Subnet mask Valid values: xxx.xxx.xxx.
5.12.19 srcmac Description Syntax Specify source MAC of packets to reject / Show specify source MAC deny access list entry / Delete specify source MAC deny access list entry srcmac deny {xdsl / | gigabit } mac srcmac list srcmac disable Parameter Name Description Source MAC deny access list number Valid values: 1~256 Default value: Type: Mandatory Port number.
5.13 ATM Description Mode Commands 5.13.1 cbr Description Syntax CBR traffic setting cbr pcr cdvt Parameter Name Description ATM Descriptor index Valid values: 1 ~ 251 Default value: Type: Mandatory Peak cell rate number Valid values: 0 ~ 65535 Default value: Type: Mandatory Cell Delay Variation Tolerance Valid values: 0 ~ 65535 Default value: Type: Mandatory 5.13.
5.13.3 ubr1 Description Syntax UBR type 1 traffic setting (atmNoClpNoScrCdvt) ubr1 pcr cdvt Parameter Name Description ATM Descriptor index Valid values: 1 ~ 251 Default value: Type: Mandatory Peak cell rate number Valid values: 0 ~ 65535 Default value: Type: Mandatory Cell Delay Variation Tolerance Valid values: 0 ~ 65535 Default value: Type: Mandatory 5.13.
Valid values: 0 ~ 65535 Default value: Type: Mandatory 5.13.5 unshp Description Syntax unshaped traffic setting (atmNoTrafficDescriptor) unshp Parameter Name Description ATM Descriptor index Valid values: 1 ~ 251 Default value: Type: Mandatory 5.13.
Valid values: 0 ~ 65535 Default value: Type: Mandatory Maximum Burst Size Valid values: 0 ~ 65535 Default value: Type: Mandatory 5.13.
5.13.
5.13.9 ubr-shp Description Syntax UBR shaped traffic setting (atmNoClpNoScr) ubr-shp pcr Parameter Name Description ATM Descriptor index Valid values: 1 ~ 251 Default value: Type: Mandatory Peak cell rate number Valid values: 0 ~ 65535 Default value: Type: Mandatory 5.13.
5.13.
5.13.
5.14 Priority List Mode Commands The commands in this section can be executed only in the Priority List execution mode. 5.14.
af12 Assured Forwarding Class 1:Medium Drop (bits:001100) af13 Assured Forwarding Class 1:High Drop (bits:001110) af21 Assured Forwarding Class 2:Low Drop (bits:010010) af22 Assured Forwarding Class 2:Medium Drop (bits:010100) af23 Assured Forwarding Class 2:High Drop (bits:010110) af31 Assured Forwarding Class 3:Low Drop (bits:011010) af32 Assured Forwarding Class 3:Medium Drop (bits:011100) af33 Assured Forwarding Class 3:High Drop (bits:011110) af41 Assured Forwarding Class 4:Low Drop (b
Parameter Name Description Destination IP address priority list number Valid values: 1~256 Default value: Type: Mandatory Priority value Valid values: 0~7 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Destination IP address Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: 0.0.0.
5.14.
5.14.6 dstmac list Description Syntax Parameter Show destination MAC priority list dstmac list None 5.14.
5.14.8 ethertype list Description Syntax Parameter Show Ether Type priority list ethertype list None 5.14.
icmp <1> (ICMP) Internet Control Message igmp (IGMP) Internet Group Management <2> ipinip IP in IP (encapsulation) <4> tcp (TCP) Transmission Control <6> grp <7> (GRP) Globin Reduction Protocol igp <9> (IGP) Any private interior gateway udp (UDP) User Datagram <17> gre (GRE) General Routing Encapsulation <47> eigrp ospf EIGRP <88> OSPF <89> Default value: Type: Mandatory 5.14.10 ipprotocol list Description Syntax Parameter Show IP protocol priority list ipprotocol list None 5.14.
Parameter Name Description Source IP address priority list number Valid values: 1~256 Default value: Type: Mandatory Priority value Valid values: 0~7 Default value: Type: Mandatory Port number. Valid values: 1~24(48) for xDSL, 1 for GBE Default value: Type: Mandatory PVC number Valid values: 1 ~ 8 Default value: Type: Mandatory Destination IP address Valid values: xxx.xxx.xxx.xxx (xxx:0~255) Default value: 0.0.0.
5.14.13 srcmac Description Syntax Specify source MAC of packets to remark vlan priority srcmac prio {xdsl / | gigabit } mac scrmac list scrmac disable Parameter Name Description Source mac priority list number Valid values: 1~256 Default value: Type: Mandatory Priority value Valid values: 0~7 Default value: Type: Mandatory Port number.
5.14.
5.14.16 tos list Description Syntax Parameter Show ToS (IP Precedence) priority list tos list None 5.14.
5.14.
5.15 Alarm Profile Mode Commands The commands in this section can be executed only in the Alarm Profile execution mode. 5.15.1 alarm mask Description Syntax Mask the alarm alarm mask Parameter Name Description Name of alarm. Valid values: Refer to Appendix B Alarm Table. Default value: Type: Mandatory 5.15.2 alarm unmask Description Syntax Unmask the alarm alarm unmask Parameter Name Description Name of alarm. Valid values: Refer to Appendix B Alarm Table.
5.15.4 alarm minor Description Syntax Set the level of the alarm to Minor alarm minor Parameter Name Description Name of alarm. Valid values: Refer to Appendix B Alarm Table.
5.16 IGMP-ACL Profile Mode Commands The commands in this section can be executed only in the IGMP-ACL Profile execution mode. 5.16.1 igmp-acl Description Syntax IGMP group ACL Setting (IP and VLAN) / Delete channel setting igmp-acl { vlan | delete} Parameter Name Description IGMP ACL channel index. Valid values: 1 ~ 256 Default value: Type: Mandatory IGMP group address Valid values: 224.0.0.0 ~ 239.255.255.255 The range of addresses from 224.0.
5.17 Rate Limit Profile Mode Commands The commands in this section can be executed only in the Rate Limit Profile execution mode. 5.17.
Default value: Type: Mandatory First Leakage Bucket Size (bits) Valid values: 1 ~ 1024 Default value: Type: Mandatory Excess Info Rate (bps) Valid values: 1536 ~ 1000000000 Default value: Type: Mandatory Second Leakage Bucket Size (bits) Valid values: 1 ~ 1024 Default value: Type: Mandatory 5.17.
5.17.
5.18 Service Profile Configure Mode Commands The commands in this section can be executed only in the Service Profile execution mode. 5.18.1 bitrate Description Syntax Set downstream/upstream Minimum/Maximum/Planned/L2 minimum bit rate bitrate {ds | us} {min | max | planned | l2} Parameter Name Description number Bit rate (kb/s). Valid values: 0-65535 Default value: Type: Mandatory 5.18.
5.18.4 mode Description Set downstream/upstream rate adaptive mode to init (rate automatically selected at start up only and does not change after that), dynamic (rate automatically selected at initialization and is continuously adapted during show time), or manual (rate changed manually) Syntax Parameter mode {ds | us} {init | dynamic | manual} None 5.18.5 noise Description Syntax Set downstream/upstream minimum impulse noise protection.
5.18.7 ra-interval Description Syntax Set Downshift/Upshift Interval in downstream/upstream direction ra-interval {ds | us} {downshift | upshift} Parameter Name Description number Downshift/Upshift interval (seconds). Valid values: 0 ~ 16383 Default value: 10 Type: Mandatory 5.18.8 service name Description Syntax Set service profile name service name Parameter Name Description Profile name.
5.19 Spectrum Profile Configure Mode Commands The commands in this section can be executed only in the Spectrum Profile execution mode. 5.19.1 aggregate Description Syntax Set downstream/upstream aggregate power level aggregate {ds | us} max powerlevel Parameter Name Description Power level (tenth dBm). Valid values: 0~25.5 step 0.1 Default value: Type: Mandatory 5.19.
Parameter Name Description index Bands array index. Valid values: 0-7 Default value: Type: Mandatory value Valid values: see the following: egress_no_control egress no control egress_notched egress notched ingress_low ingress low ingress_weak ingress weak ingress_strong ingress strong rf_signal_am RF Signal AM Type rf_signal_hamband RF Signal HAMBAND Type Default value: egress_no_control Type: Mandatory 5.19.
5.19.5 message-based Description Syntax Set minimum DS/US message-based data rate that is needed by ATU message-based {ds | us} min Parameter Name Description Min downstream/upstream message-based data rate. Valid values: 4 ~ 28 kbps Default value: Type: Mandatory 5.19.6 modem features Description Syntax Parameter Set modem features enable/disable modem features {enable | disable} None 5.19.
see all the operation modes. Default value: Type: Mandatory 5.19.9 pbomode Description Syntax Parameter Set power backoff operation mode ON/OFF pbomode us {on | off} None 5.19.10 power-mgt disable Description Syntax Parameter Disable power management function for ADSL power-mgt disable None 5.19.11 power-mgt l2 enable Description Syntax Parameter Allow autonomous L2 state entry/exit power-mgt l2 enable None 5.19.
5.19.14 power-mgt l2-time Description Syntax Set minimum time (in seconds) between an Entry into L2 low power state and the first L2 low power trim request, and between two consecutive L2 power trim requests power-mgt l2-time Parameter Name Description L2 Time value. Valid values: 0 ~ 255 (sec) Default value: Type: Mandatory 5.19.
5.19.17 psdlevel Description Syntax Set PSD level psdlevel {ds | us} max Parameter Name Description Maximum PSD level (tenth dBm/Hz). Valid values: -60 ~ -40 downstream step 0.1 -60 ~ -38 upstream. step 0.1 Default value: Type: Mandatory 5.19.18 psdshape Description Syntax Set PSD shape psdshape ds {cut-off | standard} Parameter Name Description number Cut-off frequencies at carrier. Valid values: 100-280 step 10 Default value: Type: Mandatory 5.19.
5.19.20spectrum name Description Syntax Set spectrum profile name spectrum name Parameter Name Description Name of the spectrum profile. (max 31 characters) Default value: Type: Mandatory 5.19.
5.20 TCA Profile Mode Commands The commands in this section can be executed only in the TCA Profile execution mode. 5.20.1 adsl-tca day Description Syntax Set threshold value for near-end/far-end day PM adsl-tca day {ne | fe} {es | ses | uas}
5.21 Dot1x Mode Commands The commands in this section can be executed only in the Dot1x execution mode. 5.21.1 auth-method Description Syntax Set priorities of the different authentication methods auth-method {none | radius_1 | radius_2 | radius_3 | profile} Parameter Name Description index Authentication method priority. Valid values: 1-4 Default value: Type: Mandatory 5.21.
5.21.3 server auth-port Description Syntax Set the port number for RADIUS Authentication in the Layer-4 header server auth-port Parameter Name Description index RADIUS Server index. Valid values: 1-3 Default value: Type: Mandatory number RADIUS Server authentication port Valid values: Default value: 1812 Type: Mandatory 5.21.
5.21.5 server max-fail Description Syntax Set the maximum allowable times of continuously failed authentication attempts server max-fail Parameter Name Description index RADIUS Server index. Valid values: 1-3 Default value: Type: Mandatory number RADIUS Server maximum fail number Valid values: 1-10 Default value: 2 Type: Mandatory 5.21.
5.21.7 server vlan Description Syntax The VID of the VLAN which the RADIUS server belongs to server vlan Parameter Name Description index RADIUS Server index Valid values: 1-3 Default value: Type: Mandatory number VLAN ID Valid values: 1-4094 Default value: Type: Mandatory 5.21.8 server delete Description Syntax Delete a RADIUS server setup in the system server delete Parameter Name Description index RADIUS Server index.
5.21.10 profile username password Description Syntax Set the username and password for a authentication local profile profile username password Parameter Name Description index Authenticate profile index.
Appendix A ADSL Operational Mask Table Table A-1 Bit ADSL Operational Mask Description Bit Description 0 ANSI_T1.
Appendix B Alarm Table Table B-1 Alarm ID Alarm Table Name Description 104 alm_fan_fail System Fan Fail 105 alm_self_test_fail System Self Test Fail 106 alm_above_temper System Above Temperature 107 alm_below_temper System Below Temperature 118 alm_dsl_dsp System DSP Fail 601 alm_adsl_los Near-end Loss of Signal 602 alm_adsl_lof Near-end Loss of Frame 603 alm_adsl_lom Near-end Loss of Margin 610 alm_adsl_lcd Near-end Loss Cell Delineation 612 alm_adsl_ncd Near-end No Cell De
Appendix C Cleaning the AIR Filter For better condition of cool system, please remember to clean the Air Filter every three months. This section provides the procedure for how to clean the Air Filter Procedure： Note: Before cleaning the Air Filter, please power-off the IDL-2402 first. You must loosen the connection of the Air Filter Panel to the DSLAM and pull out the Air Filter before cleaning the air filter. 1 Put on the antistatic wrist strap and connect it to a grounding point.
Appendix D Introduction for Troubleshooting This chapter describes instructions for the IDL-2402 system problems. These procedures may require the presence of technicians at remote IDL-2402 system sites and plus an operator at PC to monitor system alarms by console during maintenance. Resolving Problems Indicated Through LEDs This section describes what to do to solve problems indicated by LEDs on the system front panel.
List of Troubleshooting Procedures Type of problem Procedure Number IDL-2402 power up problems Procedure 1 ADSLx service problems (POTS service is ok) Procedure 2 POTS service problems (ADSLx service is ok) Procedure 3 Subscriber service problems (no POTS and ADSLx service) Procedure 4 Procedure 1：Troubleshooting for Power Up Problems Problem indication: The SYS LED on the front panel is not lit even though the DSLAM is powered up Alarm that indicates a system power up problem Subscribe
Procedure 2 Troubleshoot ADSLx Service Problems Problem indication: No ADSLx service to the affected subscribers (POTS service is ok). Procedure: 1 If all subscribers connected to the DSLAM are affected, and the SYS LED on the front panel is not lit, check the both end of power cords: If one of the power cords is not connected, power up the DSLAM by plugging the power cord to the power socket/power outlet.
Procedure 4 Subscriber Service Problems Problem indication: No POTS and ADSLx service to the affected subscribers. Procedure: 1 Check the connection of the subscriber lines and POTS lines at the subscriber line connector for DSLAM for subscribers that do not have POTS and ADSLx service. If this step results in POTS service to the affected subscribers but there is still no ADSLx service to them, follow Procedure 2 to troubleshoot ADSLx service problems.
EC Declaration of Conformity For the following equipment: *Type of Product *Model Number : 24-Port IP DSLAM : IDL-2402 * Produced by: Manufacturer‘s Name: Planet Technology Corp. Manufacturer‘s Address: 11F, No. 96, Min Chuan. Road, Hsin Tien Taipei, Taiwan, R.O.C. is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility (89/336/EEC, Amended by 92/31/EEC, 93/68/EEC & 98/12/EC).
